Water Supply Systems We carry out all your operations mentioned in the following standards regarding the necessary regulations in accordance with the tests and methods determined for
TS 12096 Water Heaters (instantaneous water heaters) with gas atmospheric burners - Rules for installation and use
TS EN 751-3 Sealing materials - 1 th, 2 and 3 are used for screw metallic connections in contact with all gases and hot water - Part 3: Non-sintered ptfe strips
TS EN 751-1 Sealing materials-1 th, 2 th and 3 third family used for screw metallic connections in contact with gases and hot water-Part 1: Air-hardening seal compounds
TS EN 806-1 Indoor installation - Specification for the transport of drinking and potable water - Part 1: General
TS EN 806-2 Indoor installation - Specification for the transport of drinking and potable water - Part 2: Design
TS EN 806-3 Indoor installation - Features for the transport of potable and domestic water -Part 3: Pipe dimensioning - Simplified method
TS EN 1074-1 Valves - For water supply - Compliance and verification tests with intended requirements - Part 1: General specifications
TS EN 1074-5 Valves for water supply - Compliance and verification tests for favorable design requirements - Part 5: Control valves
TS EN ISO 3822-1 Acoustics - Laboratory tests of noise emissions from devices and equipment used in water supply facilities - Part 1: Measurement method
TS EN 751-3 Sealing materials - 1 th, 2 and 3 are used for screw metallic connections in contact with all gases and hot water - Part 3: Non-sintered ptfe strips
TS EN 751-1 Sealing materials-1 th, 2 th and 3 third family used for screw metallic connections in contact with gases and hot water-Part 1: Air-hardening seal compounds
TS EN 806-1 Indoor installation - Specification for the transport of drinking and potable water - Part 1: General
TS EN 806-2 Indoor installation - Specification for the transport of drinking and potable water - Part 2: Design
TS EN 806-3 Indoor installation - Features for the transport of potable and domestic water -Part 3: Pipe dimensioning - Simplified method
TS EN 1074-1 Valves - For water supply - Compliance and verification tests with intended requirements - Part 1: General specifications
TS EN 1074-5 Valves for water supply - Compliance and verification tests for favorable design requirements - Part 5: Control valves
TS EN ISO 3822-1 Acoustics - Laboratory tests of noise emissions from devices and equipment used in water supply facilities - Part 1: Measurement method
TS EN 1717 General features of water pollution prevention devices and prevention of water pollution caused by backflow in drinking water installations
TS EN ISO 15874-1 / tst A1 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 1: General
TS EN 13443-2 + A1 Water conditioning equipment used in the building-Mechanical filters-Part 2: Particulate value 1fm up to 80 µm Performance safety and test rules
TS EN 14652 + A1 Water treatment equipment for buildings - Membrane separation devices - Performance, safety and test rules
TS EN 14743 + A1 Water treatment equipment used in the building - Softeners - Performance, safety and test requirements
TS EN 14812 + A1 Indoor water treatment device-Chemical dosing system-Preset dosing systems-Features for performance, safety and testing
TS EN 14897 + A1 Indoor water conditioning equipment - Low pressure ultraviolet radiators - Mercury devices performance safety and test rules
TS EN 13443-1 + A1 Water conditioning equipment in buildings - Mechanical filters - Part 1: Particle value 80 µm to 150 µm Specification for performance, safety and testing
TS EN ISO 21003-5 Multilayer pipe systems for indoor hot and cold water installations - Part 5: Compliance with the purpose of the system
Laboratory tests of noise emissions from devices and equipment used in water supply facilities - Part 3822: Measurement method TS EN ISO 1-1 / A1
TS EN ISO 3822-3 / A1 Acoustics - Laboratory tests of noise emissions from devices and equipment used in water supply facilities - Part 3: Installation and operating conditions for valves and devices on a line
Acoustics - Laboratory tests of noise emitted from devices and instruments used in water supply plants - Part 3822: Measurement method - Amendment 1: Measurement uncertainty TS EN ISO 1-1 / A1
TS EN ISO 3822-3 / A1 Acoustics - Laboratory tests of noise emissions from devices and equipment used in water supply facilities - Part 3: Installation and operating conditions for valves and devices on a line
TS EN ISO 1452-1 Plastic pipe systems - for drinking and potable water - Used in underground and surface pressure sewage systems - Polyvinyl chloride (PVC-U) without plasticizer - Part 1: General
TS EN 806-4 Indoor installation - Specification for the transport of drinking and potable water - Part 4: Installation
TS EN 806-4 Indoor installation - Requirements for the transport of potable and domestic water - Part 4: Installation
TS EN ISO 1452-5 Plastic pipe systems - Used for drinking and potable water, underground and surface pressure drainage and sewage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 5: suitability of the system
TS EN ISO 15877-2: 2009 / A1 Plastic piping systems for hot and cold water systems Chlorinated poly (vinyl chloride) (pvc-C) - Part 2: Pipes
TS EN ISO 15877-5 / A1 Plastic pipe systems - For hot and cold water systems - Chlorinated poly (vinyl chloride) (pvc-C) - Part 5: Suitability of the system for its purpose
TS EN ISO 1452-3 Plastic pipe systems - For drinking and potable water - Used in underground and surface pressure sewage systems - Made of polyvinyl chloride (pvc-U) with no plasticizer added - Part 3- Fittings
TS EN ISO 21003-2: 2008 / A1 Multilayer pipe systems for indoor hot and cold water installations - Part 2: Pipes
TS 10672-2 EN ISO 15875-2 / tst A1 -Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 2: Pipes
TS 10672-1 EN ISO 15875-1 / tst A1 -Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 1: General
TS EN 12201-1 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 1: General
TS EN 12201-3 + A1 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 3: Fittings
TS EN 12201-5 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 5: suitability of the system for its purpose
TS EN 806-5 Indoor installation - Specification for the transport of drinking and potable water - Part 5: Operation and maintenance
TS EN 806-5 Indoor installation - Features for the transport of drinking and potable water -Part 5: Operation and maintenance
TSE CEN / TR 12108 Plastic pipe systems - Pressure pipe systems for hot and cold - Rules for laying drinking and utility water pipes in the building
TS EN 12201-4 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
tst 200454344 Prepaid water meter
TS ISO 13781: 2012 (EN) Flexible hose fittings in drinking water installations - Functional features and test methods
TS EN ISO 15874-1 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 1: General
TS EN ISO 15874-2 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 2: Pipes
TS EN ISO 15874-3 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 3: Fittings
TS EN ISO 15874-5 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 5: System suitability
TSE CEN / TS 14632 Plastic pipe systems - Used in pressure and non-pressurized drainage and sewage systems - Unsaturated polyester resin (up) based glass reinforced thermoset plastics (grp) conformity assessment guide
TSE CEN / TS 14807 Plastic piping systems - Glass fiber reinforced thermoset plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for structural analysis of buried GRP-UP pipelines
TS EN 1074-4 Valves - For water supply - Compliance and verification tests with intended requirements - Part 4: Air valves
TS ISO 16422 Pipes and fittings used for water transmission under pressure - From poly (vinyl chloride) (PVC_O) without oriented plasticizer - Specification
TS EN ISO 15874-3 Plastic pipe systems - For hot and cold water - Polypropylene (PP) - Part 3: Fittings
TS EN ISO 15874-1 Plastic piping systems for hot and cold water - Polypropylene (Pp) - Part 1: General
TS 2170 Underground installation of water and gas pipes
TS EN ISO 15874-5 Plastic pipe systems - For hot and cold water - Polypropylene (PP) - Part 5: System suitability
TS EN ISO 15874-2 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 2: Pipes
TSE CEN / TS 12201-7 Plastic pipe systems - For drinking and potable water - Polyethylene (pe) - Part 7: Conformity assessment guide
TS ISO 16422 Pipes and fittings for water transmission under pressure - Oriented, non-plasticizing polyvinyl chloride (PVC-O) - Specification
TSE CEN / TS 1452-7 Plastic pipe systems - Part of polyvinyl chloride (pvc-U) with no plasticizer for drinking and potable water 7: Conformity assessment guide
TS EN ISO 1452-2 / D1 Plastic pipe systems - For potable and potable water - Used in underground and surface pressure sewage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 2: Pipes
TS EN ISO 4064-1 Water meters for cold drinking water and hot water - Part 1: Metrology and technical requirements
TS EN ISO 4064-2 Water meters for cold drinking water and hot water - Part 2: Test methods
TS EN ISO 4064-3 Water meters for cold drinking water and hot water - Part 3: Test report format
TS EN ISO 4064-4 Water meters for cold drinking water and hot water - Part 4: Non-metrological requirements not covered by ISO 4064-1
TS EN ISO 4064-5 Water meters for cold drinking water and hot water - Part 5: Installation requirements
TSE CEN / TS 12201-7 Plastic pipe systems - For drinking and potable water - Polyethylene (pe) - Part 7: Conformity assessment guide
TSE CEN / TS 1452-7 Plastic pipe systems - Part of polyvinyl chloride (pvc-U) with no plasticizer for drinking and potable water 7: Conformity assessment guide
TS EN 1487 Building valves - Hydraulic safety groups - Tests and features
TSE CEN / TS 14632 Plastic pipe systems - pressurized and unpressurized; for drainage, sewage and water applications - Glass reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Conformity assessment guide
TS EN 14154-4 Water meters - Part 4: Additional functions
TS EN ISO 13845 Plastic pipe systems - Joints made of ring-type elastomeric seal for thermoplastic pressure pipes - Test method for sealing under internal pressure and angular bending
TS EN ISO 13844 Plastic pipe systems - Joints with elastomeric sealing ring type pipe heads used with pressure plastic pipes - Test method for sealing under vacuum, angular deflection and deformation
tst EN 13618 Flexible connection hoses for drinking water installations - Functional specifications and test methods
TS EN 488 Central heating pipes - Pre-insulated pipe systems for direct buried hot water networks - Steel valve assembly for polyurethane heat-insulated, polyethylene outer casing steel service pipes
TS EN ISO 11177 Glass and porcelain enamels - internal and external enamelled valves and pressure piping for untreated and drinking water lines - Quality requirements and testing
TS EN ISO 15876-1 Plastic pipe systems -Used in hot and cold water systems-Polybutylene (pb) -Chapter 1: General
TS EN ISO 15876-2 Plastic pipe systems -Used in hot and cold water systems-Polybutylene (pb) -Chapter 2: Pipes
TS EN ISO 15876-5 Plastic pipe systems - Used in hot and cold water systems - Polybutylene (pb) - Part 5: suitability of the system for its purpose
TS 102 EN 512 Fiber cement - pressure pipes and fittings
TS 102 EN 512 / tst T Fiber cement - pressure pipes and fittings
TS 274-2 EN 1452-2 / tst T Plastic piping systems for drinking and potable water - Part of polyvinyl chloride (pvc-U) without plasticizer 2: Pipes
TS 274-3 EN 1452-3 / tst T Plastic piping systems for drinking and potable water - Non-plasticizing polyvinyl chloride (pvc-U) - Part 3: Fittings
TS 459 Hatches used in drinking water network
TS 459 Hatches used in drinking water network
TS EN 641 Reinforced concrete pipes - Pressure - Steel jacketed type - Joints and joint special parts
TS 737 Water filters (sand filters)
EN 806-4: 2010 -
TS 15 EN 1213 Valves - Used in buildings - Copper alloy stop valves for drinking water supply - Tests and specifications
TS 1258 Clean water installation account rules
TS EN ISO 1452-2 Plastic pipe systems - For drinking and potable water - Used in underground and surface pressure sewage systems - Polyvinyl chloride (pvc-U) without plasticizer - Part 2: Pipes
TS EN ISO 1452-3 Plastic pipe systems - Used in potable and domestic water and underground and surface pressure drainage and sewerage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 3- Fittings
TS EN ISO 1452-4 Plastic pipe systems - Used for potable and potable water and underground and surface pressure drainage and sewage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 4: Valves
TS ENV 1452-6 Plastic piping systems for potable and potable water - Polyvinylchloride without plasticizer (pvc-U) - Part 6: Laying rules
TS EN ISO 1452-5 Plastic pipe systems - For drinking and potable water and for underground and surface pressure sewage systems - Part of polyvinyl chloride (pvc-U) without plasticizer 5: System suitability
TS EN 14652 + A1 Indoor water treatment equipment - Membrane separation devices - Performance, safety and test rules
TS EN 1488 Valves - Used in buildings - Expansion groups - Tests and features
TS EN 1489 Valves - Used in buildings - Pressure safety valves - Tests and specifications
TS EN 1567 / T1 Valves - for buildings - Water pressure reducing and combined water pressure reducing valves - Features and tests
TS EN 1717 General features of pollution prevention devices for protection against contamination of drinking water in the water installation and backflow
TSE 9954-7 CEN ISO / TS 15876-7 Plastic piping systems - Used in hot and cold water systems - Polybutylene (pb) - Part 7: Conformity assessment guide
TS 10762-2 EN ISO 15875-2 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 2: Pipes
TS 10762-3 EN ISO 15875-3 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 3: Fittings
TSE 10762-7 CEN ISO / TS 15875-7 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 7: Conformity assessment guide
TS 11425 Insulation fittings-ready for installation for electrical insulation in building gas and water service lines
TSE CEN ISO / TS 15874-7 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 7: Conformity assessment guide
TSE 12182-7 CEN ISO / TS 15877-7 Plastic piping systems for hot and cold water systems Chlorinated poly (vinyl chloride) (pvc-C) - Part 7: Conformity assessment guide
TS EN 12502-1 Protection of metallic materials against corrosion - Guidance on the assessment of corrosion similarity in water distribution and storage systems - Part 1: General
TS EN 12502-4 Protection of metallic materials against corrosion - Guidance on the assessment of corrosion similarity in water distribution and storage systems - Part 4: Factors affecting stainless steels
TS EN 12502-2 Protection of metallic materials against corrosion - Guidance on the assessment of corrosion similarity in water distribution and storage systems - Part 2: Factors affecting copper and copper alloys
TS EN 12502-3 Protection of metallic materials against corrosion - Guidance on the assessment of corrosion similarity in water distribution and storage systems - Part 3: Factors affecting hot-dip galvanized iron-based materials
TS EN 12502-5 Protection of metallic materials against corrosion - Guidance on the assessment of corrosion similarity in water distribution and storage systems - Part 5: Factors affecting cast iron, unalloyed and low alloy steels
TS EN 13078 Preventing contamination from drinking water backflow - Immersion supply air gap with flood sluice and air intake - Group a, type c
tst EN 13079 Preventing contamination from back-escape of potable water-Air gap with injector-Class a- Type d
TS EN 14095 Water conditioning equipment inside buildings - Aluminum anode electrolytic treatment systems - Performance, safety and test conditions
TS EN 14367 Prevents uncontrollable backflow with different pressure zones - Family c, type a
TS EN 14623 Apparatus used to prevent contamination by backflow in potable water - Air gaps with minimum return flow (verified by measurement and test) - Family a, type g
TS EN 14743 + A1 Water conditioning equipment used in buildings - Softeners - Performance, safety and test rules
TS EN 14898 + A1 Indoor water conditioning equipment - Active material filters - Performance safety and test rules
TS EN 15092 Valves used in buildings - Inline hot water supply valves - Tests and rules
TS EN 15096 Devices to prevent pollution by drinking water backflow - Hose union anti-Vacuum valves - Dn 15 dn Family including H, type b and d 25 - General technical specifications
TS EN 15161 Indoor water treatment - Installation, operation, maintenance and repair
TS EN 15219 + A1 Indoor water supply - Nitrate removal - Requirements for performance, safety and testing
TS EN 15848 Water treatment equipment inside buildings - Chemical dosing system - Features for performance, safety and testing
TS EN ISO 15875-1 / A1 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 1: General -A1
TS EN ISO 15875-2 / A1 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 2: Pipes - A1
TS EN ISO 15877-5 Plastic pipe systems for hot and cold water systems Chlorinated poly (vinyl chloride) (pvc-C) - Part 5: suitability of the system for its purpose
TS EN ISO 21003-1 Multilayer pipe systems for indoor hot and cold water installations - Part 1: General
TS EN ISO 21003-3 Multilayer pipe systems for indoor hot and cold water installations - Part 3: Connections
TSE CEN ISO / TS 21003-7 Multilayer pipe systems for indoor hot and cold water installations - Part 7: Guidelines for conformity assessment
TS EN ISO 21003-2 Multilayer pipe systems for indoor hot and cold water installations - Part 2: Pipes
TS EN ISO 22391-5 Plastic pipe systems - For hot and cold water systems - Made of polyethylene with increased temperature resistance (pe-Rt) - Part 5: Compliance with system purpose
TS EN ISO 22391-2 Plastic pipe systems - For hot and cold water systems - Made of polyethylene with increased temperature resistance (pe-Rt) - Part 2: Pipes
TS EN ISO 22391-3 Plastic pipe systems - For hot and cold water systems - Made of polyethylene with increased temperature resistance (pe-Rt) - Part 3: Fittings
TS EN ISO 22391-1 Plastic pipe systems - For hot and cold water systems - Made of polyethylene with increased temperature resistance (pe-Rt) - Part 1: General
TS EN 24006 Flow measurement in closed pipes - Terms, descriptions and symbols
200233823 Water filters - Ceramic