We provide testing, auditing and certification services for all of the following standards. We are professional and experienced in all operations.
TS 1902 EN 588-1 Fiber cement pipes-Section for sewerage and drainage 1: Non-pressure pipes, joint fittings, joint special fittings
TS EN 1453-1 Plastic pipe systems - Profiled walls - Used for disposal of indoor wastewater (at high and low temperatures) - Made of polyvinyl chloride (pvc-U) without plasticizer - Part 1 - Pipes and system features
TS EN 1455-1 Plastic pipe systems - Used for the disposal of indoor wastewater (hot and cold) - Acrylonitrile - Butadiene - Styrene (abs) - Part 1: Pipes, fittings and system features
TS EN 12056-3 Drainage systems - Indoor - Part 3: Design and calculation of terrace drainage
TS EN 12056-4 Drainage systems - Indoor - Part 4: Design and calculation of waste water pumping stations
TS EN 13564-1 Flood protection devices in buildings-Part 1: Requirements
TS EN 13564-2 Flood protection devices for buildings - Part 2: Test methods
TSE CEN / TS 1451-2 Plastic pipe systems -Polypropylene (pp) used for disposal of cold and hot waste water in the building -Chapter 2: Conformity assessment guide
TSE CEN / TS 1519-2 Plastic pipe systems -Used for disposal of indoor waste water -Pietylene (pe) -Chapter 2: Conformity assessment guide
TSE K 169 Plastic pipe systems - Used for the disposal of cold and hot wastewater in the building - Made of mineral doped polypropylene (pp) material - Soundproof pipes, fittings and system features
TSE CEN / TS 12666-2 Plastic pipe systems - For unpressurized groundwater and drainage - From polyethylene (pe) - Part 2: Conformity assessment guide
TS EN ISO 13260 Thermoplastic pipe systems for unpressurized underground drainage and waste water - Simultaneous temperature cycling and external load resistance test method
TSE CEN / TS 1566-2 Plastic pipe systems - Used for the disposal of cold and hot waste water in the building - Chlorinated polyvinyl chloride (pvc-C) - Part 2: Conformity assessment guide
TSE CEN / TS 14632 Plastic pipe systems - Used in pressure and non-pressurized drainage and sewage systems - Unsaturated polyester resin (up) based glass reinforced thermoset plastics (grp) conformity assessment guide
TS EN 15012 Plastic pipe systems - Soil and waste discharge systems in the building - Performance characteristics for pipes, fittings and fittings
TS EN ISO 11297-1 Plastic piping systems - For the renovation of underground drainage and sewerage networks under pressure - Part 1: General
TS EN ISO 11297-3 Plastic pipe systems - For the renovation of underground drainage and sewerage networks under pressure - Part 3: Laying with crimped pipes
TSE CEN / TS 14807 Plastic piping systems - Glass fiber reinforced thermoset plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for structural analysis of buried GRP-UP pipelines
TSE CEN / TR 13801 Waste discharge in soil and building structure (low and high temperature) Plastic pipe systems - Thermoplastic - Recommended Application for Installation
TSE CEN / TS 14632 Plastic pipe systems - pressurized and unpressurized; for drainage, sewage and water applications - Glass reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Conformity assessment guide
TS EN 1253-1 Sieves for buildings - Part 1: Floor drains insulated against water with a depth of at least 50 mm
TS EN 1253-2 Sieves for buildings - Part 2: Floor drains and roof drains
TS EN 14366 Laboratory measurement of noise from wastewater plants
TS EN 12050-1 Wastewater lifting plants for buildings and settlements - Part 1: Wastewater lifting plants for faeces
TS EN 12050-2 Wastewater lifting plants for buildings and settlements - Part 2: Wastewater lifting plants without feces
TS EN 12050-3 Wastewater lifting plants for buildings and residential areas - Part 3: Lifting plants for limited applications
TS EN 12050-4 Wastewater lifting plants for buildings and settlements - Part 4:: One-way valves for wastewater with and without feces
TSE K 169 / T1 Plastic pipe systems - Used for disposal of cold and hot wastewater in the building - Made of mineral doped polypropylene (PP) - Features of soundproof pipes, fittings and system
TS EN 1253-4 Strainers - Used in buildings - Part 4: Inlet covers
TS EN 1253-3 Strainers - Used in buildings - Part 3: Quality control
tst EN 1253-1 Sieves for buildings - Part 1: Floor drains with siphon seal against water at least 50 mm depth
tst EN 1253-2 Drains for buildings - Part 2: Floor drains and roof drains
TSE K 522 Filter Coatings for Surface Drainage Pipes
TS EN 1453-1 Plastic pipe systems - Profiled walls - Used for disposal of indoor wastewater (at high and low temperatures) - Made of polyvinyl chloride (pvc-U) without plasticizer - Part 1 - Pipes and system features
TSE CEN / TS 1453-2 Plastic pipe systems - Profiled walls - Used for disposal of indoor wastewater (at high and low temperatures) - Made of polyvinyl chloride (pvc-U) without plasticizer - Part 2 - Conformity assessment guide
TS EN 12050-1 Wastewater lifting plants for buildings and settlements - Part 1: Wastewater lifting plants for faeces
TS 327 Strainers for sewage installation
TS EN 588-2 Pipes - Made of fibrous cement - For drainage and sewage - Part 2: Inspection manholes and inspection chambers
TS EN 1451-1 Plastic pipe systems - Used for disposal of cold and hot wastewater in buildings - Section of polypropylene (pp) 1: Pipes, fittings and system features
TS EN 1451-1 / T1 Plastic pipe systems-Used for disposal of cold and hot wastewater in building-Polypropylene (pp) section 1: Pipes, fittings and system properties
TS 1480 Mud traps and rain funnels (for rainwater grating sets and sewer manhole covers)
TS 1480 / T1 Mud traps and rain funnels (for rainwater grating sets and sewer manhole covers)
TS 1907 Concrete brackets for rainwater grate chimneys
TS 1907 / T1 Concrete bracelets for rainwater grating chimneys
TS 9128 Pipes - Made of rigid pvc for drainage
TS EN ISO 11296-1: 2011 Plastic pipe systems for the renovation of underground pressure-free drainage and sewage lines - Part 1: General
TS EN 12056-5 Attractive drainage systems - Indoor - Part 5: Installation and testing, operation, maintenance and operating instructions
TS EN 12056-1 Attractive drainage systems - Indoor - part 1: General rules and performance rules
TS EN 12056-2 Attractive drainage systems - Indoor - section 2: Plumbing system - Design and calculation
TS EN 12056-3 Attractive drainage systems - Indoor - part 3: Roof drainage - Design and calculation
TS EN 12056-4 Attractive drainage systems - Indoor - section 4: Wastewater lifting plants - Design and calculation
TS EN 12095 Plastic pipe systems - Supports for rainwater pipe systems -Support resistance test
TS EN 12109 Drainage systems for indoor use - vacuum
tst EN 12380 Air intake valves for drainage systems - Rules, test methods and conformity assessment
TS EN 12380 Air intake valves for drainage systems - Rules, test methods and conformity assessment
TS EN 12666-1: 2005 + A1: 2011 Plastic pipe systems for non-pressurized groundwater and drainage - Polyethylene (pe) - Part 1: Specification for pipes, fittings and system
TS EN 12763 Pipe and fittings - Manufactured with fiber cement - Used in building waste water discharge systems - Dimensions and technical specifications used in shipment
TS EN 13564-1 Flood protection devices - Used in buildings - Part 1: Rules
TS EN 13564-3 Flood protection devices - Used in buildings - Part 3: Quality assurance
TS EN 14366 Laboratory measurement of noise from wastewater plants "
TS 13473 Concrete pipes and fittings - Dn 1750 larger than mm