We carry out your testing and auditing services in accordance with national and international regulations and standards. We serve all the following standards.
TS ISO 9935 Non-destructive testing-Penetrant error detectors-General technical conditions
TS ISO 3453 Non-destructive testing-Penetrant inspection-Verification procedures
TS EN ISO 196 Formed copper and copper alloys - Determination of residual stress - Mercury (I) nitrate test
TS 1695 EN ISO 2624 Copper and copper alloys-Determination of average grain size
TS EN 10275 Metallic materials-Pipe ring hydraulic pressure test
TS EN ISO 2566-2 Steel - Conversion of elongation values - Part 2: Austenitic steels
TS EN ISO 7799 Metallic materials - 3 mm thickness or thinner - Reverse bending test
TS 1381 EN ISO 642 Hardenability test by applying water to the steel tip (jomin test)
TS 4277 EN 25754 Sintered metal materials - Except hardmetals - Notched impact test piece
TS 6441 EN 23312 Sintered metal materials and hard metals - Determination of Young's modulus
TS EN 10275 Metallic materials-Pipe ring hydraulic pressure test
TS EN ISO 2566-2 Steel - Conversion of elongation values - Part 2: Austenitic steels
TS EN ISO 7799 Metallic materials - 3 mm thickness or thinner - Reverse bending test
TS 1381 EN ISO 642 Hardenability test by applying water to the steel tip (jomin test)
TS 4277 EN 25754 Sintered metal materials - Except hardmetals - Notched impact test piece
TS 6441 EN 23312 Sintered metal materials and hard metals - Determination of Young's modulus
TS EN 12681 Casting; Radiographic examination
TS EN 10276-2 Determination of oxygen in steel and iron - Part 2: Infrared method after melting under inert gas
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of iron in zinc alloys - Spectrophotometric method
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of iron in primary zinc - Spectrophotometric method
TS EN 12441-6 Zinc and zinc alloys - Chemical analysis department 6 - Determination of aluminum and iron - Flame atomic absorption spectrophotometric method
TS EN 12681 Castings-Radiographic examination
TS EN ISO 14577-3 Metallic materials - Instrument trace test for hardness and material parameters - Part 3: Calibration of reference blocks
TS EN ISO 8491 Metallic materials - Pipe (full cross section) - Bending test
TS EN ISO 8493 Metallic materials - Pipe - Mouth expansion test (iso 8493: 1998) / note: To replace En 10234 (1993-10).
TS EN 10160 Ultrasonic testing of flat steel products with a thickness equal to or more than 6 mm (reflection technique)
TS EN ISO 6507-4 Metallic materials - Vickers hardness test - Part 4: Charts and hardness values
TS EN 10184 Chemical analysis of ferrous materials Determination of phosphorus in steels and iron-Spectrophotometric method
TS EN 10325 Steel - Determination of yield strength increase by heat treatment effect
TS EN 61788-6 Superconductivity - Part 6: Measurement of mechanical properties - Tensile test of Cu / Nb-Ti compound superconductors at room temperature
TS EN 10247 Micrographic examination of non-metallic residual content of steels using standard drawings
TS EN 573-5 Aluminum and aluminum alloys - Chemical composition and shape of formable products - Part 5: Coding of shaped products
TS EN ISO 6507-4 Metallic materials - Vickers hardness test - Part 4: Hardness value charts
TS EN ISO 4499-1 Hard metals - Metallographic determination of microstructure - Part 1: Photomicrograph and description
TS EN ISO 3369 Impermeable sintered metal materials and hard metals - Determination of density
TS EN ISO 10893-1 Non-destructive testing of steel pipes - Part 1: Automatic electromagnetic examination of seamless and welded (excluding submerged arc welding) steel pipes for verification of hydraulic tightness
TS EN ISO 10893-2 Non-destructive testing of steel pipes - Part 2: Automatic eddy current testing of seamless and welded (excluding submerged arc welding) steel pipes for the detection of defects
TS EN ISO 10893-6 Non-destructive testing of steel tubes - Part 6: Radiographic examination of weld seam in welded steel tubes for the detection of defects
TS EN ISO 10893-7 Non-destructive testing of steel pipes - Part 7: Digital radiographic examination of weld seam in welded steel pipes for the detection of defects
TS EN ISO 10893-8 Non-destructive testing of steel pipes - Part 8: Automatic ultrasonic testing of seamless and welded steel pipes for the detection of planar defects
TS EN ISO 10893-10 Non-destructive testing of steel pipes - Part 10: Automatic full environmental ultrasonic testing of seamless and welded (excluding submerged arc welding) steel pipes for the detection of longitudinal and / or transverse defects
TS EN ISO 10893-11 Non-destructive testing of steel pipes - Part 11: Automatic ultrasonic testing of weld seam in welded steel pipes for the detection of transverse and / or longitudinal defects
TS EN ISO 6892-2 Metal materials - Tensile test - part 2: High temperature test method
TS EN ISO 376 Metallic materials - Calibration of force measuring devices for the verification of single-axis test machines
TS EN ISO 26203-2 Metallic materials - Tensile test at high tensile speeds - Part 2: Servehydraulics and other test systems
TS EN 12680-3 Casting - Ultrasonic inspection - Part 3: Spheroidal graphite cast iron
TS EN 10200 Chemical analysis of ferrous materials - Determination of boron in steel - Spectrophotometric method
TS EN ISO 2739: 2012 Sintered metal bushings - Determination of radial crush strength
TS EN ISO 643: 2012 Steels - Micrograph determination of apparent grain size
TS EN ISO 9513 Metal materials - Calibration of extensometers used in uniaxial tests
TS EN 14584 Non-destructive testing - Acoustic emission - Inspection of pressurized metal equipment during verification tests - Planar placement of Ae welds
TS EN ISO 377: 2013 Steel and steel products - Collection and preparation of samples and test pieces for mechanical tests
TS EN ISO 3326: 2013 Hardmetals - Determination of magnetization (coercivity)
TS EN ISO 20482 Metallic materials - Sheet and strip - Erichsen buckling test
TS 8311 EN 25580 Non-destructive testing-Industrial radiographic illuminators-Minimum requirements
TS EN 10355 Chemical analysis of ferrous materials - Inductively coupled plasma optical emission spectrometric analysis of unalloyed and low alloy steels - Determination of Si, Mn, P, Cu, Ni, Cr, Mo and Sn following dissolution by nitric acid and sulfuric acid [Routine method ]
TS EN ISO 18265 Metal materials - Cycle of hardness values
TS EN ISO 8492 Metal materials - Pipe - Flattening test
TS EN ISO 8494 Metal materials - Pipe - Flange test
TS EN ISO 8495 Metal materials - Tubing - Ring expansion test
TS EN ISO 8496 Metal materials - Tubing - Ring tensile test
TS EN 10211 Chemical analysis of ferrous materials - Determination of titanium in steel and cast iron - Flame atomic absorption spectrometric method
TS EN ISO 5579 Non-destructive testing - Radiographic examination of metallic materials by film and X-ray or gamma rays - General rules
TS EN ISO 10893-4 Non-destructive testing of steel pipes - Part 4: Liquid penetrant inspection of seamless and welded steel pipes for the detection of surface defects
TS EN ISO 10893-1 Non-destructive testing of steel pipes - Part 1: Automatic electromagnetic examination of seamless and welded (excluding submerged arc welded) steel pipes for verification of hydraulic sealing (ISO 10893-1: 2011)
TS EN ISO 10893-2 Non-destructive testing of steel pipes - Part 2: Inspection of seamless and welded (excluding submerged arc-welded) steel pipes with automatic eddy currents for the detection of defects (ISO 10893-2: 2011)
TS EN ISO 10893-8 Non-destructive testing of steel pipes - Part 8: Automatic ultrasonic testing of seamless and welded steel pipes for the detection of planar defects
TS EN 61788-19 Superconductivity - Part 19: Measurement of mechanical properties - Room temperature tensile test of Nb3Sn composite superconductors reacting
TS EN ISO 9513 / AC Metal materials - Calibration of extensometers used in uniaxial tests - Teknik Korigendum 1
TS EN ISO 10113 Metallic materials - Determination of plastic strain rate of bands, sheets and strips
TS EN ISO 10275 Metallic materials - Sheet and strip - Determination of tensile stress hardening coefficient
TS EN ISO 16808 Metallic materials - Sheet and strip - Determination of biaxial stress-strain curve by blowing test with optical measuring systems
TS EN ISO 10893-11 Non-destructive testing of steel tubes - Part 11: Automatic ultrasonic inspection of welded seam in welded steel tubes for the detection of transverse and / or longitudinal defects (ISO 10893-11: 2011)
TS EN ISO 6506-1 Metallic materials - Brinell hardness test - Part 1: Test method
TS EN ISO 6506-2 Metallic materials - Brinell hardness test - Part 2: Verification and calibration of test equipment
TS EN ISO 6506-3 Metallic materials - Brinell hardness test - part 3: Calibration of reference blocks
TS EN ISO 6506-4 Metallic materials - Brinell hardness test - part 4: Hardness value charts
tst EN 61788-19 Superconductivity - Part 19: Measurement of mechanical properties - Room temperature tensile test of Nb3Sn composite superconductors
TS EN 15063-1 Copper and copper alloys - Determination of principal components and impurities by wavelength-separated x-ray fluorescence spectrometry - Part 1: Guide for routine method
TS EN 15703-2 Copper and copper alloys - Determination of manganese content - Part 2: Flame atomic absorption spectrometry method (AAAS)
TS EN 10211 Chemical analysis of ferrous materials - Determination of titanium in steel and cast iron - Flame atomic absorption spectrometric method
TS EN ISO 8492 Metal materials - Pipe - Flattening test
TS EN ISO 8494 Metal materials - Pipe - Flange test
TS EN ISO 8495 Metal materials - Tubing - Ring expansion test
TS EN ISO 18265 Metal materials - Cycle of hardness values
tst EN ISO 8492 Metal materials - Pipe - Flattening test
TS EN ISO 10893-6 Non-destructive testing of steel tubes - Part 6: Radiographic examination of weld seam in welded steel tubes for the detection of defects
TS EN 10113-1 Hot rolled products - Fine grain weldable structural steels - Part 1: General technical delivery conditions
TS EN ISO 6508-2 Metallic materials - Rockwell hardness test - part 2: Verification and calibration of test equipment and tips
TS EN ISO 6508-3 Metallic materials- Rockwell hardness test- Part 3: Calibration of reference blocks
TS ISO 1143 Metals- Rotating bar bending fatigue tests
TS EN 61788-21 Superconductivity - Part 21: Superconducting wires - Test methods for practical superconducting wires - General specifications and guidance
Metallic materials - Tensile test - Part 6892: Low temperature test method TS EN ISO 3-2015: 3
TS EN 15079 Copper and copper alloys - Analysis by spark-based optical emission spectrometer (S-OES)
TS EN ISO 14577-1 Metallic materials - Instrument trace test for hardness and material parameters - Part 1: Test method
TS EN ISO 14577-2 Metallic materials - Instrument trace test for hardness and material parameters - Part 2: Verification and calibration of test machines
TS EN ISO 14577-3 Metallic materials - Instrument trace test for hardness and material parameters - Part 3: Calibration of reference blocks
TS EN ISO 7438 Metallic materials - Bending test
TS EN ISO 14556 Steel - Charpy impact test of V notched specimen - Instrument test method
TS EN ISO 16859-1 Metallic materials - Leeb hardness test - Part 1: Test method
TS EN ISO 16859-2 Metallic materials - Leeb hardness test - Part 2: Calibration and verification of test equipment
TS EN ISO 16859-3 Metallic materials - Leeb hardness test - Part 3: Calibration of reference test blocks
TS EN ISO 7500-1 Metal materials - Verification of single-axis static test machines - Part 1: Tensile / compression test machines - Verification and calibration of force measuring system
TS EN 10361 Alloy steels - Determination of nickel content - Inductively coupled plasma optical emission spectrometry
TS EN ISO 20482 Metallic materials - Sheet and strip - Erichsen buckling test
TS EN ISO 4499-3 Hard metals - Metallographic determination of microstructure - Part 3: Measurement of microstructure properties in Ti (C, N) and WC / cubic carbide based ser metals
TS EN ISO 4499-4 Hard metals - Metallographic determination of microstructure - part 4: Properties of porosity, carbon defects and eta phase content
TS EN ISO 6508-1 Metallic materials- Rockwell hardness test- Part 1: Test method
TS ISO 12135 Metallic materials-Combined test method for determination of quartzist fracture toughness
TS EN ISO 6892-1 Metallic materials - Tensile test - Part 1: Test method at ambient temperature
TS EN 10228-3: 2016 Non-destructive testing of forged steels - Part 3: Ultrasonic testing of ferritic or martensitic forged steels
TS EN 10228-2: 2016 Non-destructive testing of forged steels - Part 2: Penetrant testing
TS EN 10228-4: 2016 Non-destructive testing of forged steels - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings
TS EN 10228-1 Non-destructive testing of forged steels - Part 1: Magnetic particle inspection
TS EN ISO 148-1 Metallic materials- Charpy tapping test- Part 1: Test method
TS EN ISO 148-2 Metallic materials-Charpy tapping test-Part 2: Verification of test machine (pendulum tapping)
TS EN ISO 148-3 Metallic materials-Charpy tapping test-Part 3: Preparation and characterization of v-notch test pieces for indirect evaluation of tapping
TS EN ISO 14577-4 Metallic materials - Instrument trace test for hardness and material parameters - Part 4: Test method for metallic and non-metallic coatings
TS EN ISO 3928 Sintered metal materials, except hard metals - fatigue test pieces
TS EN ISO 6892-1 Metallic materials - Tensile test - Part 1: Test method at ambient temperature
TS ISO 12107 Metallic materials - Fatigue testing - Statistical planning and analysis of data
TS EN ISO 204 Metallic materials-Stress uniaxial creep test-Test method
TS 205-2 ISO 7801 Metallic materials - Wire - Bending test
TS EN ISO 6507-3 Metallic materials - Vickers hardness test - Part 3: Calibration of reference blocks
TS EN ISO 6507-1 Metallic materials - Vickers hardness test - Part 1: Test method
TS EN ISO 6507-2 Metallic materials - Vickers hardness test - Part 2: Verification and calibration of test equipment
TS 601 EN 10036 Chemical analysis methods of ferrous materials - Total carbon determination in steel and iron - Gravimetric method after combustion in oxygen flow
Zinc and zinc alloys - Chemical analysis - Part 1122: Determination of aluminum in zinc alloys - Titrimetric method
TS ISO 1812 Copper alloys-Determination of iron content-1, 10-Phenanthroline spectrophotometric method
TS 2023-1 EN ISO 2566-1 Steels - Conversion of elongation values - part 1: Carbon and less alloy steels
Steels - Conversion of elongation values - Part 2023: Austenitic steels TS 2-2566
TS EN ISO 2639 Steels - Determination and verification of the effective depth obtained in carburizing and hardening
TS EN ISO 2740 Sintered metal materials - Excluding hard metals - Tensile test pieces
TS 2780 EN ISO 2626 Copper-Hydrogen brittleness test
TS 3142 EN ISO 3887 Steels - Determination of decarburization depth
TS EN ISO 3327 Hard materials - Determination of transverse tensile strength
TS ISO 3738-1 / T1 (Number modification, TS EN ISO 3738-1) Hard metals - Rockwell hardness test (scale a) - Part 1: Test method
TS EN ISO 3738-1 (Formerly: TS ISO 3738-1) Hard metals - Rockwell hardness test (scale a) - Part 1: Test method
TS EN ISO 3738-2 (Formerly: TS ISO 3738-2) Hard metals - Rockwell hardness test (scale a) part 2: Preparation and calibration of standard test blocks
TS ISO 3738-2 / T1 (Number modification: TS EN ISO 3738-2) Hard metals - Rockwell hardness test (scale a) part 2: Preparation and calibration of standard test blocks
Zinc and zinc alloys - Part 3815: Analysis of solid samples by optical emission spectrometry
TS EN ISO 3815-2 Zinc and zinc alloys - Part 2: Analysis by inductively coupled plasma optical emission spectrometer
TS 3868 ISO 4967 Steel - Determination of non-metallic residue content - Micrographic method using standard diagrams
TS 4222 EN ISO 3325 Sintered metal materials - excluding hard metals - Determination of cross fracture strength
TS EN ISO 4499-2 Hard metals - Metallographic determination of microstructure - Part 2: Wc particle size measurement
TS EN ISO 4507 Sintered iron based materials, embossed or carbo nitrided - Determination and verification of surface hardness depth by micro hardness test
TS EN ISO 4545-1 Metallic materials - Knoop hardness test - Part 1: Test method
TS EN ISO 4545-2 Metallic materials - Knoop hardness test - Part 2: Verification and calibration of test equipment
TS EN ISO 4545-3 Metallic materials - Knoop hardness test - Part 3: Calibration of reference blocks
TS EN ISO 4545-4 Metallic materials - Knoop hardness test - Part 4: Hardness values chart
TS EN ISO 4934 Determination of sulfur content of steel and cast iron-Gravimetric method
TS ISO 5949 Tool steels and bearing steels - Micrographic method for the evaluation of the distribution of carbides using reference photomicrographs
TS EN ISO 6892-2: 2011 Metal materials-Tensile test section 2: High temperature test method
TS ISO 6933 Non-destructive testing - Magnetic particle acceptance inspection of railway vehicles moving materials
tst 7150 EN ISO 4934 Steel and cast iron - Determination of sulfur content - Gravimetric method
TS EN ISO 7500-2 Metallic materials - Verification of uniaxial static testing machines - Part 2: Tensile creep testing machines - Verification of applied load
TSE ISO / TR 7705 charpy v in steel specifications - Guide for determining rupture energy in notched test pieces
TS 205-3 EN ISO 7799 Metallic materials - Sheet and strip of thickness 3 mm or less - Reverse bending test
TS 205-4 EN ISO 8491 Metallic materials - Pipe (full section) - Bending test
TS EN ISO 9556 (Former number: TS ISO 9556) Steel and iron-Determination of total carbon-Induction furnace after combustion by infrared absorption method
TS ISO 9556 / T1 (Number modification, TS EN ISO 9556) Steel and iron - Determination of total carbon - By infrared absorption method after burning in induction furnace
TS EN 10188 Chemical analysis of ferrous materials-Determination of chromium in steel and iron-Flame atomic absorption spectrometric method
TS EN 10212 Chemical analysis of iron-based materials-Determination of arsenic in steel and iron-Spectrophotometric method
TS EN 10229 Evaluation of hydrogen resistance to steel cracking
TS EN 10229 / T1 Evaluation of hydrogen cracking (no) resistance in steel products
TS EN 10274 Metallic materials - Tear test with weight reduction
TS EN 10275 Metallic materials - Pipe ring hydraulic pressure test
TS EN 10276-1 Chemical analysis of ferrous materials - Determination of oxygen in steel and iron - Part 1: Preparation and preparation of steel samples for oxygen determination
TS EN 10276-2 Chemical analysis of ferrous materials - Determination of oxygen content in steel and iron - Part 2: Infrared method after melting under inert gas
TS EN 10306 Ultrasonic testing of iron and steel-parallel flanged h beams and rope beams
TS EN 10307 Non-destructive testing-Ultrasonic testing of austenitic and austenitic-ferritic stainless steel flat products with a thickness equal to 6 mm (including 6 mm)
TS EN 10308 Non-destructive testing-Ultrasonic testing of steel bars
TS EN 10315 Routine method for the analysis of high alloy steel by x-ray fluorescence spectrometer (xrf) using a close technique
TS EN 10319-1 Metallic materials-Tensile stress relaxation tests-Part 1: Method for test machines
TS EN 10319-2 metallic materials - Tensile stress relief test - Part 2: Procedure for bolted joint models
TS EN 10325 Steel - Determination of increase in yield strength due to heat treatment effect [furnace hardening index]
TS EN 10328 Iron and steel - Conventional depth and hardening determination after surface treatment
TS 10389 Non-destructive testing-Fixed and moving magnetizers other than hand-held magnetizers
TS EN ISO 10714 Steel and iron - Determination of phosphorus content - phosphovanadomolybdate spectrophotometric method
TSE ISO / TR 10719 Determination of steel and iron-Free carbon content-Infrared absorption method after combustion in induction furnace
TS ISO 10720 / T1 (Number modification: TS EN ISO 10720) Determination of steel and iron-nitrogen content-Thermal conductivity method after melting under inert gas stream
TS EN ISO 10893-9: 2011 Non-destructive testing of steel tubes - Part 9: Automatic ultrasonic inspection of steel strips / plates used in the manufacture of welded tubes for the detection of planar defects
TS EN ISO 10893-4: 2011 Non-destructive testing of steel tubes - Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface defects
TS EN ISO 10893-12: 2011 Non-destructive testing of steel pipes - Part 12: Fully automatic automatic ultrasonic thickness examination of seamless and welded (except submerged arc welded) steel pipes
TS EN ISO 10893-5: Non-destructive testing of steel pipes - Part 2011: Magnetic particle inspection of seamless and welded ferromagnetic steel pipes for the detection of surface defects
TS EN ISO 10893-3: 2011 Non-destructive testing of steel pipes - Part 3: Automatic full perimeter leakage flux inspection of seamless and welded (except submerged arc welding) ferromagnetic steel tubes for the detection of longitudinal and / or transverse defects
TS ISO 11484 Steel products-Employer's qualification system for non-destructive testing personnel
TS EN ISO 11489 Determination of platinum in platinum alloy alloys - Gravimetric determination by reduction with mercury (1) chloride
TS EN ISO 12004-1 Metallic materials - Sheets and strips - Determination of forming boundary rounds - Part 1: Measurement and forming boundary diagrams in the press workshop
TS EN ISO 12004-2 Metallic materials - Sheets and strips - Determination of forming boundary rounds - Part 2: Determination of forming boundary rounds in a laboratory
TS ISO 12169 Nickel oxide - Determination of nickel content - Electrolytic deposition method
TS EN 12258-2 Aluminum and aluminum alloys - Terms and definitions - Part 2: Chemical analysis
TS EN 12311-1 Flexible sheets for waterproofing - Part 1: Bituminous sheets for waterproofing of roofs - Determination of tensile properties
TS EN 12441-3 Zinc and zinc alloys-Chemical analysis-Part 3: Determination of lead, cadmium and copper-Flame atomic absorption spectrometric method
TS EN 12441-5 Zinc and zinc alloys - Chemical analysis - part 5: Determination of iron in primary zinc - Spectrophotometric method
TS EN 12441-6 Zinc and zinc alloys - Chemical analysis department 6 - Determination of aluminum and iron - Flame atomic absorption spectrophotometric method
TS EN 12441-7 Zinc and zinc alloys - Chemical analysis - Part 7 - Determination of tin - Flammable atomic absorption spectrometric method after extraction TS
TS EN 12441-8 Zinc and zinc alloys - Chemical analysis - Part 8 - Determination of secondary tin in zinc - Atomic absorption of flames
TS EN 12441-10 Zinc and zinc alloys - Chemical analysis department 10 - Determination of chromium and titanium in zinc alloy - Spectrophotometric method "
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of iron in zinc alloys - Spectrophotometric method
Zinc and zinc alloys - Chemical analysis - Part 12441 - Determination of nickel in zinc alloy - Flame atomic absorption spectrometric method
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of aluminum in zinc alloys - Titrimetric method - Part 1-1 / A1
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of magnesium in zinc alloys - Flame atomic absorption spectrometric method
Zinc and zinc alloys - Chemical analysis - Part 12441: Determination of magnesium in zinc alloys - Flame atomic absorption spectrometric method
TS 12604 Metallic coatings-Determination of coating mass in iron and steel materials coated with aluminum
TS EN 12680-1 Casting - Ultrasonic inspection - part 1: General purpose steel castings
TS EN 12680-2 Casting - Ultrasonic inspection - part 2: Steel castings to be subjected to high stresses
TSE ISO / TR 12735-1 Mechanical testing of metals - Symbols used in conjunction with descriptions - Part 1: Symbols and descriptions in published standards
TS EN 13615 Methods for ingot tin analysis - Determination of impurity element content in tin content of% 99,85 to% 99,90 by atomic spectrometry
TS ENV 14029 Lead and lead alloys - Analysis of the lead after removal of lead by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma emission spectrometry (ICP-ES)
TS EN 14242 Aluminum and aluminum alloys - Chemical analysis - Inductive coupling plasma optical emission spectral analysis
TS EN 14361 Aluminum and aluminum alloys - Chemical analysis - Sampling of metal melts
TS EN ISO 14577-1 Metallic materials - Instrument trace test for hardness and material parameters - Part 1: Test method
TS EN ISO 14577-2 Metallic materials - Instrument trace test for hardness and material parameters - Part 2: Verification and calibration of test machines
TS EN 14726 Aluminum and aluminum alloys - Chemical analysis - Rules for the optical emission spectrometric analysis of sparks.
TS EN 15063-2 Copper and copper alloys - Determination of main components and impurities by wavelength-separated x-ray fluorescence spectrometry - Part 2: Routine method
TSE ISO / TR 15461 Steel forgings - Test frequency, sampling conditions and test methods for mechanical tests
TS EN 15690-2 Ductile iron pipes, fittings and accessories - Internal polyurethane liner for pipes and fittings - Features and test methods
TS EN 23878 Hard metals - Vickers hardness test
TS EN 24489 Sintered hard metals - Sampling and testing
TS EN 24503 Hardmetals-Determination of metal content-X-Ray fluorescence-Melting method
TS EN 24884 Hard metals - Sampling and testing of sintered test pieces from powders
TS EN ISO 26203-1 Metallic materials - Tensile test at high tensile speeds - Elastic rod type system
TS EN ISO 3785 Steel - Test piece axes display
TS EN ISO 196 Formed copper and copper alloys - Determination of residual stress - Mercury (I) nitrate test
TS EN ISO 11489 Determination of platinum in platinum alloy alloys - Gravimetric determination by reduction with mercury (1) chloride