In accordance with the Rubber and Plastics Industry test requirements, it provides testing, inspection, inspection and certification services for all of the following standards.
TS EN 2259 Aviation series - Silicone rubber (VMQ) - 50 IRHD hardness
TS EN ISO 9664 Adhesives - Fatigue properties of structural adhesives subject to tensile slip - Test methods
TS EN ISO 9665 Adhesives - Gums of animal origin - Sampling and test methods
TS EN ISO 12017 Plastics poly (methyl methacrylate) - Sheets - Two and three shells - Test methods
TS EN ISO 13468-1 Plastics - Determination of the total light transmittance of transparent materials - Part 1: Single beam beam device
TS 681 ISO 599 Plastics-Polyamide homopolymers-Determination of extractables with boiling methanol
TS 1883 ISO 705Determination of rubber latex 5 ° c-40 ° c
TS 2437 EN ISO 1110 (Formerly: TS 2437 ISO 1110) Accelerated conditioning of plastics-polyamides test pieces
TS 2437 EN ISO 1110 (Formerly: TS 2437 ISO 1110) Accelerated conditioning of plastics-polyamides test pieces
TS 1724 EN ISO 1675 (Formerly: TS 1724 ISO 1675) Determination of density of plastics, liquid resins-Pycnometer method
TS 4650-1 ISO 3597-1 Plastics-Glass fiber reinforced-Determination of mechanical properties of wick-reinforced resin rods-Part 1: General experiments and preparation of rods
TS 4650-2 ISO 3597-2 Plastics-Glass fiber reinforced-Determination of mechanical properties of wick-reinforced resin rods-Part 2: Determination of flexural strength
TS 4650-4 ISO 3597-4 Plastics-Glass fiber reinforced-Determination of mechanical properties of wick-reinforced resin rods section 4: Determination of apparent shear strength between laminates
TS 1851 ISO 1407 Rubbers-Solvent extractable determination
TS 1531 ISO 1629 Rubbers and latex-designations
TS 1006-1 ISO 182-1 Determination of the tendency of plastic vinyl vinyl chloride homopolymers and copolymers to produce hydrogen chloride and other acidic products at high temperatures - Part 1: Congo red method
TS EN 1945 Adhesive tapes - Determination of sudden adhesion
TS EN 1944 Adhesive tapes-Determination of low-speed milking strength
TS 1006-2 EN ISO 182-2 (Formerly: TS 1006-2 ISO 182-2) Determination of the tendency to release hydrogen chloride and other acidic products of plastics based on vinyl chloride homopolymers and copolymers of pulps and products at high temperatures-Part 2:
TS 1006-3 EN ISO 182-3 (Former no: TS 1006-3 ISO 182-3) Determination of the tendency of release of hydrogen chloride and other acidic products of plastics based on vinylchloride homopolymers and copolymers of pulps and products at high temperatures - Part XtUMX method
TS 1398-3 EN ISO 527-3 Plastics-Determination of tensile properties-Part 3: Test conditions for films and sheets
TS 1936 ISO 1652 Rubber latex-Determination of vistosity
TS 6993 ISO 6188 Plastics-Poly (alkylene terephthalate) granules-Determination of water percentage
TS 7685 ISO 4593 Plastics-Film and sheets-Thickness determination by mechanical screening
Plastics - Ethylene / vinylacetate (e / vac) molding and extruding agents TS EN ISO 4613-2 section 2: Preparation of test specimens and determination of their properties
TS 3779 EN ISO 2818 Plastics - Preparation of test pieces by machining
TS ISO 10499 Tires and wheels for industrial vehicles-Solid tires for pneumatic tire rims (metric series) -short indication, dimensions and marking
TSE ISO / TR 7621 Rubber or plastic coated rollers Request and order - Recommendations for technical information required by the customer
TSE ISO / TR 7664Rubber-Natural and synthetic-Raw solid state-General rules for storage
TS 11008 EN ISO 4638 Porous, flexible polymer materials - Determination of air flow permeability
TS EN 12023 Adhesive tapes-Determination of water vapor permeability in warm and humid atmosphere
TS EN 12024 Adhesive tapes-Determination of high temperature and moisture resistance
TS EN 12026 Adhesive tapes-High-speed unwinding force measurement
TS EN 12027 Adhesive tapes-Determination of flame resistance
TS EN 12029 Adhesive tapes-Determination of corrosive ions soluble in water
TS EN 12030 Adhesive tapes-Determination of impact resistance
TS EN 12031 Adhesive tapes - Determination of explosion strength
TS EN 12035 Adhesive tapes-Separation of tape from back surface
TS EN 12575 Plastics - Thermosetting molding compounds - Determination of moisture degree of fibers in smc
TS 5773 EN ISO 13758 Liquefied petroleum gases - Determination of propane dryness - Valve freezing method
TS EN ISO 4613-1 (Formerly: TS ISO 4613-1) Plastics-Ethylene / vinyl acetate (e / vac) molding and extruding agents-Part 1: Indication and identification with markings
TS 10909 EN 549 Rubber (elastomeric) materials - Gas devices and gas equipment for gaskets and diaphragms 19.04.1996 83.140.50
TS 4594 EN ISO 3386-1Porous, flexible polymer materials - Determination of stress / strain properties under pressure - Part 1: Low density materials
TS EN ISO 14126Fiber reinforced plastic composites - Determination of plane compression properties
TS EN ISO 14631Pulse-modified polystyrene (ps-1) extruded sheets - Properties and test methods.
TS 1966 ISO 35 Natural rubber latex - Concentrated determination of mechanical stability
TS 1966 ISO 35 Natural rubber latex - Concentrated determination of mechanical stability
TS 1722-1 ISO 1209-1 Porous plastics-Hard-Stretch tests-Part 1: Bending test
TS 1722-2 ISO 1209-2 Porous plastics-Hard-Stretch tests-Part 2: Determination of stretch properties
TS EN 1246 Adhesives - Determination of ash and sulfate ash
TS ISO 14663-1 Plastics - Ethylene / vinyl alcohol (evoh) copolymer molding and extruding agents - Part 1: System and principles for marking properties
TS ISO 14663-2 Plastics - Ethylene / vinyl alcohol (evoh) copolymer molding and extrusion materials - Part 2: Preparation of test pieces and determination of their properties
TS ISO 4433-1 Thermoplastic tubes - Resistance to chemical liquids - Classification - Part 1: Immersion test method
TS ISO 4433-2 Thermoplastic tubes - Resistance to chemical fluids - Classification - Part 2: Polyolefin tubes
TS EN ISO 10093 Plastics - Fire tests - Standard ignition sources
TS EN 12573-1 Welded, static, unpressurized thermoplastic tank - Part 1: General requirements
TS EN 12573-3 Welded, static, unpressurized thermoplastic tanks - Part 3: Design and calculation for single-wall rectangular prism-shaped tanks
TS EN 12960 Adhesives for paper and cardboard, packaging and disposable health products - Determination of slip resistance
TS EN ISO 14125Plastic composites - Fiber reinforced - Determination of flexural properties
TS EN ISO 14129 Plastic composites - Fiber reinforced - Determination of in-plane shear stress / shear stress response - Including in-plane shear modulus and shear strength - Stress test method of ± 45 °
TS EN ISO 14129Plastic composites - Fiber reinforced - In-plane shear stress / shear stress determination - Including in-plane shear modulus and shear strength - ± 45 ° tensile test method
TS EN ISO 7808 Plastics - Thermosetting molding materials - Determination of transfer flow
TS EN ISO 14527-3 Plastics - Urea / formaldehyde and urea / melamine - Formaldehyde powder molding mixtures (uf- and f / mf-Pmc) - Part 3: Properties of some molding mixtures
TS EN 12575 Plastics - Thermosetting molding compounds - Determination of moisture degree of fibers in smc
TS EN ISO 14527-1 Plastics - Urea formaldehyde and urea / melamine - Formaldehyde powder molding mixtures (uf-ve f / mf-Pmc) - Part 1: System and principles of indication of properties
TS EN ISO 14527-2 Plastics - Urea - Formaldehyde and urea / melamine - Formaldehyde powder molding mixtures (UF- and UF / MF-PMC) - Part 2: Preparation of test specimens and determination of their properties
TS EN 12963 Adhesives - Determination of free monomer content in synthetic polymer based adhesives
TS 6905 EN ISO 14632 Polyethylene sheets (pe-Hd) - Extruded - properties and test methods
TS 8931 EN ISO 1873-1 Plastics-Polypropylene (pp) molding and extrusion materials-Part 1: Principles for marking system and features
TS 462 EN ISO 172 Plastic - Molded phenol formaldehyde - Detection of free ammonia
TS EN ISO 527-4Plastics - Determination of tensile properties - Part 4: Test requirements for isotropic and orthotropic fiber reinforced plastic composites
TS EN ISO 10724-1 Plastics - Preparation of test pieces by injection molding from thermosetting molding mixtures in powder form - Part 1: General principles and molding of multi-purpose test pieces (iso 10724-1: 1998)
TS EN ISO 11542-1 Plastics - Very high molecular weight polyethylene (pe-Uhmw) molding and extrusion materials - Part 1: Features system and principles
TS 4698 ISO 34-1 Tires and thermoplastics-Determination of tear strength section 1: With test pieces in strip, open and moon form
TS EN ISO 11401Plastics - Phenolic resins - Separations by liquid chromatography
TS EN 12481 Adhesive tapes-Terms and recipes
TS EN 12765 Adhesives - Thermoset wood adhesives - For non-structural applications - Classification
TS EN 12961 Adhesives - Solvent based and for dispersion - Determination of maximum activation life and optimum activation temperatures
TS EN 12964 Adhesives - Long lasting - For leather and footwear materials - Determination of temperature variation of strength of bonded joints
TS EN ISO 13000-2 Plastics - Polytetrafluoroethylene (ptfe) semi-products - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 11343Adhesives - Determination of dynamic strength of high-strength adhesives against separation in impact applications, wedge impact method
tst ISO 11235 Rubber pulp additives - Sulfonamide accelerators - Test methods
TS EN ISO 13468-2 Plastics - Determination of the total light transmittance of transparent materials - part 2: Double beam path device
TS EN 1720 Adhesives for paper and cardboard packaging and disposable sanitary products - Determination of dispersibility
TS EN 1721 Adhesives - Paper and cardboard, packaging and disposable health products - Measurement of sudden adhesion for pressure sensitive adhesives - Determination of sudden adhesion of rotating ball
TS EN ISO 10724-2 Plastics - Preparation of test pieces from powder thermoset molding mixtures (pmcs) by injection molding section 2: Small plates
TS EN ISO 10093 Plastics - Fire tests - Standard ignition sources
TS ISO 10840 Plastics - Application guide for standard fire tests
TS EN 13733 Concrete structures - Products and systems for protection and repair - Test methods - Determination of the strength of structural bonding materials
TS EN 13787 Elastomers for gas pressure regulators and associated safety devices in systems with inlet pressure up to 100 bar
TS EN 12765 Adhesives - Thermoset wood adhesives for non-structural applications - Classification
TS EN 12964 Adhesives - For leather and footwear materials - molding adhesives - Determination of heat resistance of bonding at increasing temperatures
TS EN ISO 1183-3 Plastics-Non-porous plastics-Density determination methods-Part 3: Gas pycnometer method
TS EN ISO 1043-4 Plastics - Symbols and abbreviated terms section 4: Flame retardants
TS 1676 EN ISO 305 Plastics - Determination of the thermal stability of polyvinylchloride, chlorine-containing homopolymers and copolymers and their pulp - Method of color decay
TS 1973 EN ISO 1600 Plastics - Cellulose acetate - Determination of light absorption of test specimens prepared by molding using different heating times
TS 8455 EN ISO 14631 Impact-resistant polystyrene (ps-I) sheets - Extruded - Specifications and test methods
TS EN 1122 Plastics - Determination of cadmium - Wet cracking method
TS EN 1905 Plastic piping systems - Polyvinylchloride (pvc-U) pipes, fittings and fittings - Method of evaluating pvc content based on total chloride content
TS EN ISO 12115Plastics - Fiber reinforced - Thermosetting molding mixtures and prepregs - Determination of fluidity, consistency and shelf life
TS EN ISO 9702 Plastics - Amine epoxide hardeners - Nitrogen determination - Primary, secondary and tertiary amine groups
TS EN ISO 2578 Plastics - Time - Determination of temperature limits - After prolonged exposure to heat
TS EN 205 Wood adhesives-For non-structural applications-Test methods-Determination of tensile shear strength of lap joints
TS EN ISO 14529-3 Plastics- Melamine / phenolic powder molding mixtures- (mc-Pmc) - Part 3: Properties of some molding mixtures
TS 2366 EN ISO 2114 Plastics (polyester resins) - Paints and varnishes (binders) - Determination of partial acid value and total acid value
TS 1854 ISO 1875 plastics - Plasticizer-added cellulose acetate - Determination of the amount of substance that can be extracted with diethyl ether
TS EN 13733 Concrete structures - Products and systems for protection and repair - Test methods - Determination of strength of adhesives used in construction
TS 8241 ISO 8660 Plastics - Determination of permanganate absorption number of caprolactam - Spectrometric method
TS EN ISO 8795 Plastic piping systems - For drinking and potable water - Evaluation of material passage - Determination of material passage values from plastic pipes, fittings and connections (ISO 8795: 2001)
TS EN ISO 15908 Adhesives - For thermoplastic pipe systems - Test method for determination of temperature stability of adhesives
TS EN 13677-2 Reinforced thermoplastic molding pulps - Specifications for gmt - Part 2: General specifications and test methods
TS EN 13706-1 Reinforced plastic composites - Part 1: Marking
TS EN 13706-1 Reinforced plastic composites - Part 1: Marking
TS EN 13706-2 Reinforced plastic composites - Part 2: General specifications and test methods
TS EN 13706-2 Reinforced plastic composites - Part 2: General specifications and test methods
TS EN 13706-3 Reinforced plastic composites - Part 3: Specific features
TS EN 13706-3 Reinforced plastic composites - Part 3: Specific features
TS EN 14410 Self-adhesive tapes - Measurement of tensile strength and elongation at break
tst ISO 4081 Internal combustion engines - Cooling systems - Rubber pipes and hoses - Specifications
TS EN ISO 8257-2 Plastics - Poly (methyl methacrylate) (pmma) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN 14233 Food contact materials and articles - Plastics - Determination of the transition temperature in food and plastic encounter during microwave and conventional oven heating
TS EN 14410 Self-adhesive tapes - Measurement of tensile strength and elongation at break
TS EN ISO 7822 Textile - Glass reinforced plastics - Cavity content, glow loss, determination of mechanical dispersion and statistical counting methods
TS EN ISO 9054 Porous plastics - Test method for hard - self - shelling high density materials
TS EN 14510 Footwear - Test methods for the assessment of ecological criteria
TS EN 14598-3 Reinforced thermoset pulps - Specification for sheet molding pulp (smc) and bulk molding pulp (bmc) - Part 3: Specific features
TS ISO 11501: 2003 / T1 Plastics-Films and sheets-Determination of size change with temperature effect
TS EN 1895 Adhesives for paper, cardboard, packaging and disposable sanitary products-For flexible / flexible type joints 180 ° -T peel test
TS EN 13207 Thermoplastic silage films
TS EN ISO 14526-1 Plastics - Phenolic powder molding mixtures (pf-Pmc) - Part 1: Basis for marking system and properties
TS EN ISO 14526-2 Plastics - Phenolic powder molding mixtures (pf-Pmc) - Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 11501Plastics-Films and sheets-Determination of size change with temperature effect
TS EN ISO 14126 / AC Fiber reinforced plastic composites - Determination of compression properties in plane direction
TS EN ISO 14125 / AC Fiber reinforced plastic composites - Determination of bending properties
TS EN ISO 179-2Plastics-Determination of Charpy impact properties-Part 2: Instrument impact test
TS EN ISO 527-4Plastics - Determination of tensile properties - Part 4: Isotropic and orthotropic fiber reinforced composites
TS EN ISO 1043-4 Plastics-Symbols and abbreviated terms-Part 4: Flame retardants
TS EN 1122 Plastics - Determination of cadmium - Wet shredding method
TS EN ISO 3672-2 Plastics - Unsaturated polyester resins (up-R) - Part 2: Preparation of test pieces and determination of their properties
TS EN 495-5 Flexible sheets for waterproofing - Determination of low temperature foldability - Part 5: Plastic and rubber sheets for waterproofing on roofs
TS EN 12436 Adhesives-For load-bearing timber structures-Casein based adhesives-Classification and performance criteria
TS EN 12961 Adhesives - For leather and footwear materials - Determination of the maximum operating life and optimum operating temperature of solvent based and dispers type adhesives
TS EN ISO 14616Plastics - Heat-shrinkable films of polyethylene, ethylene copolymers and mixtures thereof - Determination of shrinkage and tensile stresses
TS EN ISO 14692-3 Glass fiber reinforced plastic (ctp) pipe systems - used in the oil and gas industry - Part 3: System design
TS EN ISO 7765-1 (Formerly: TS ISO 7765-1) Plastic films and sheets-Determination of impact strength by free-falling mass method-Part 1: Ladder method
TS ISO 7765-2 Plastic films and sheets-Determination of impact strength by free falling mass method-Part 2: Instrument drilling test
TS 5430 EN 204 Classification of thermoplastic wood adhesives for non-structural applications
TS EN ISO 12058-1-plastics - Determination of viscosity using ball-drop viscometer - Part 1: Slope pipe method
TS EN 1943 Adhesive tapes-Determination of static shear adhesion
TS ISO 6235 Determination of the raw-block polystyrene content of rubber - Ozonation method
TS EN 13473-1 Reinforcement materials - Characteristics of multi-axis, multi-ply fabrics - Part 1: Part 1: Indication
TS EN 13473-2 Reinforcement materials - Properties of multi-axis, multi-ply fabrics - Part 2: Test methods and general criteria
TS EN 13473-3 Reinforcement materials - Properties of multi-axis, multi-ply fabrics - Part 3: Special criteria
TS EN 13887 Structural adhesives - Guide to surface preparation of metals and plastics before bonding
TS EN 13894-1Concrete structures - Products and systems for protection and repair - Test methods - Determination of fatigue under dynamic loads - Part 1: During hardening
TS EN 438-7 Decorative laminated sheets (hpl) - High pressure compressed - Thermoset resin based - Part 7: Composite panels (hpl) and compressed laminates for interior and exterior walls and ceiling finishing
Plastics - Non-porous plastics - Density determination methods - Part 1183: Gradient density column method TS EN ISO 2-2 Plastics
TS EN ISO 1183-3 Plastics-Non-porous plastics-Density determination-Part 3: Gas pycnometer method
TS EN ISO 2580-2 Plastics-Acrylonitrile / butadiene / styrene (abs) molding and extrusion materials-Test methods
TS EN ISO 846 Plastics - Evaluation of the effect of microorganisms (technical committee stage)
TS EN ISO 1856 Porous, flexible polymer materials - Determination of crushing rate under pressure
TS EN ISO 4610 Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis with air-jet screening device
TS EN ISO 4892-1 Plastics-Methods of exposure to laboratory light sources-Section 1: General rules
TS ISO 7267-1 Rubber coated rollers - Determination of apparent hardness - Part 1: Irhd method
TS ISO 4664-2 Tire - Vulcanized or thermoplastic - Determination of dynamic properties - Part 2: Pendulum torsion methods at low frequencies
TS ISO 4209-1 Tires and wheels for trucks and buses (metric treads) section 1: Tires
TS EN ISO 22088-2 Plastics - Determination of resistance to environmental stress cracking - Part 2: Constant tensile load method
TS EN ISO 22088-3 Plastics - Determination of resistance to environmental stress cracking - Part 3: Twisted strip method
TS EN ISO 22088-4 Plastics - Determination of resistance to environmental stress cracking - Part 4: Ball or needle clamping method
TS EN 13787 Elastomers for gas pressure regulators and associated safety devices in systems with inlet pressure up to 100 bar
TS EN ISO 483 Plastics - Small closed systems for conditioning and testing using aqueous solutions to provide constant relative humidity
TS EN 438-7 Decorative laminated sheets (hpl) - High pressure compacted - Thermoset resin based section 7: Composite panels (hpl) and compressed laminates for interior and exterior walls and ceiling finishing
TS ISO 9988-2 Plastics - Polyoxymethylene (pom) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN 13706-1 Reinforced plastic composites - Properties of extruded profiles - Part 1: Marking
TS EN 13706-1 Reinforced plastic composites - Properties of extruded profiles - Part 1: Marking
TS EN ISO 2580-2 Plastics - Acrylonitrile-Butadiene-Styrene (abs) molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 14126Fiber reinforced plastic composites - Determination of in-plane compression
TS EN 40-7 Lighting poles - Part 7: Fiber properties reinforced with polymer composites in lighting poles
TS ISO 9413 Wheel tire valves - Dimensions and short designation
TS EN ISO 15023-2 Plastics - Poly (vinyl alcohol) (pval) materials - Part 2: Specification
TS EN ISO 307 Plastics- Polyamides- Determination of viscosity number
TS EN 1612-1 + A1 Rubber and plastic machinery - Reaction molding machines - Part 1: Safety requirements for measuring and mixing units
TS EN ISO 7391-1 Plastics - Polycarbonate (pc) molding and extrusion materials - Part 1: System and principles of marking features
TS EN ISO 7391-2 Plastics - Polycarbonate (pc) - Molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 9988-1 Plastics - Polyoxymethylene (pom) molding and extruding agents - Part 1: Guidelines for marking system and features
TS EN 10131 Cold-rolled low-carbon and high yield strength flat steel products for cold forming, uncoated and zinc or electrolytically zinc-nickel coated - Dimension and shape tolerances
TS EN ISO 13468-2 Plastics - Determination of the total light transmittance of transparent materials - Part 2: Double beam path device
TS EN 14256 Adhesives for non-structural wood applications - Test method and requirements for static load resistance
TS EN 1942 Adhesive tapes - Thickness measurement
TS EN ISO 4651 / tst A1 Rubber or plastic coated fabrics - Determination of adhesion strength between surfaces
TS EN 1417 + A1 Plastic and rubber machines - Rollers with two rollers - Safety rules
tst EN 1612-2 + A1 Rubber and plastic machinery - Reaction molding machines - Part 2: Safety requirements for reaction molding plants
TS EN 263 Sanitary ware - Cross-linked cast acrylic sheets for bath tubs and shower trays for domestic use
TS EN ISO 15103-2 Plastics - Poly (phenylene ether) (PPE) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 3582 / tst A1 Flexible porous polymeric materials-Laboratory evaluation of horizontal combustion properties of small test specimens exposed to a small flame
TS EN ISO 12086-1 / AC Plastics - Molding and extrusion materials with fluoropolymer dispersions - Part 1: System and principles of marking features
TS ISO 6194-1 Rotary shaft lip seals with elastomeric seals - Part 1: Nominal dimensions and tolerances
TS EN 1942 Adhesive tapes - Thickness measurement
TS EN ISO 3251 Paints, varnishes and plastics - Determination of non-volatile matter
TS EN ISO 10350-1 Plastics - Accumulation and presentation of comparable single note data section 1: Molding materials
TS EN 1417 + A1 / AC Plastic and rubber machinery - Rollers with two rollers - Safety rules
TS EN 12436 Adhesives for load-bearing wood structures - Casein adhesives - Classification and performance characteristics
TS ISO 8873-1 Hard porous plastics - Spray-applied polyurethane foam for thermal insulation - Part 1: Material properties
tst ISO 8873-2 Rigid porous plastics-Spray polyurethane foam for thermal insulation processes 2: Applications
TS ISO 8873-3 Hard porous plastics - Spray-applied polyurethane foam for thermal insulation - Part 3: Test methods
TS EN ISO 14557 / A1 Fire fighting hoses - Rubber and plastic suction hoses and hose assemblies
TS EN 1114-3 + A1 Plastic and plastic machinery - Extruders and extrusion lines - Part 3: Safety rules for transport
TS EN ISO 7823-2 Plastics - Poly (methyl methacrylate) sheets - types, dimensions and specifications - Part 2: Extruded sheets
TS EN ISO 8256 Plastics- Determination of tensile-impact strength
TS EN ISO 8974 Plastics-Phenolic resins-Determination of phenol residue-Gas chromatographic method
TS EN ISO 11339 Adhesives - Stripping test of two flexible parts bonded together
TS EN 14294 Adhesives for leather and footwear materials - Preparation of adhesion test pieces by molding
TS EN 1464 Adhesives-Determination of peel forces of high adhesion strength tapes-Floating roller method
TS EN ISO 8986-1 Plastics - Polybutene (pb) molding and extrusion materials - Part 1: System and principles of marking features
TS EN 14444 / AC Structural adhesives - Qualitative assessment of strength of bonded systems - Wedge break test
TS EN 15870 Adhesives - Determination of tensile strength of face joints
TS ISO 6117 Road vehicles - Elastomer dust holding tires for drum hydraulic wheel brake cylinders with non-petroleum-based hydraulic brake fluid (operating temperature up to 100 0C)
TS EN 12808-4 Joint fillers - For tiles - Part 4: Determination of shrinkage
TS EN 438-8 Decorative laminated sheets (hpl) - High pressure compression - Thermoset resin based (often called laminated) - Part 8: Classification and specifications for design laminates
TS ISO 6194-2 Rotary shaft lip seals with elastomeric seals - Part 2: Terms and definitions
TS EN ISO 3821 Gas welding equipment - Rubber hoses for welding, cutting and similar works
TS EN ISO 7231 Polymer materials - Porous and flexible - Method of measuring air flow value - When pressure drop is constant
TS EN ISO 178 Plastics-Determination of flexural properties
TS EN ISO 877-2 Plastics - Methods of exposure to daylight - Part 2: Leaving directly behind sunlight and window glass
TS EN ISO 3386-1 / A1 Porous, flexible polymer materials - Determination of stress / strain properties under pressure - Part 1: Low density materials
TS EN 13245-2 / AC Plastics - Non-plasticizing polyvinylchloride (pvc-U) profiles for building applications - Part 2: Pvc-U profiles
TS EN 13245-2 Plastics-Polyvinylchloride (pvc-U) profiles without joining plasticizer for building applications-Part 2: Pvc-U profiles
TS EN 681-1 / AC Elastomeric seals - For water and drainage applications - Material specifications - Part 1: Rubber
TS EN 681-1 / T1Esteromeric seals - Used in water and drainage applications - Material specifications - Part 1: Rubber
TS EN 1243 Adhesives - Determination of free formaldehyde in amino and amidoformaldehyde condensates
TS EN 1245 Adhesives - Determination of Ph - Test method
TS EN ISO 10927 Plastics - Determination of molecular mass and molecular mass distribution of polymer species by matrix assisted laser desorsion / ionization flight / transition time mass spectrometry (Maldi-Tofms)
TS EN 12808-4: 2009 / AC: 2011 Joint fillers - For tiles - Part 4: Determination of shrinkage
TS EN ISO 4671 Rubber and plastic hose and hose assemblies - Methods for measuring the dimensions of hoses and lengths of hose assemblies
TS EN 13245-1 Plastics - Polyvinylchloride (PVC-U) profiles without plasticizers - for building applications - Part 1: Indication of light colored profiles with signs
TS EN 15860 Plastics - Thermoplastic semi-finished products for processing - Specification and test methods
TS EN ISO 4611 Plastics - Determination of the effect of hot and humid environment, sprayed water and salt mist.
TS EN ISO 9311-2 Adhesives - for thermoplastic pipe systems - Part 2: Determination of shear strength
TS ISO 23529 Tires - General procedures for the preparation and conditioning of test pieces for physical test methods
TS EN ISO 179-2 / A1 Plastics-Determination of Charpy impact properties-Part 2: Impact test with measuring instrument-Modification 1: Accuracy data
TS EN ISO 7214 Porous plastics-Polyethylene-Test methods
TS EN ISO 3251 Paints, varnishes and plastics - Determination of non-volatile matter content
EN ISO 2440 / tst A1 Flexible and hard porous polymeric materials - Accelerated aging tests
TS EN ISO 3386-1 / tstA1 Porous, flexible polymer materials - Determination of stress / strain properties under pressure - Part 1: Low density materials
TS EN ISO 11339Adhesives - Stripping test for two flexible parts bonded together
TS EN 14869-1 Structural adhesives - Determination of shear behavior of structural adhesion zones - Part 1: Torsional test method using end-glued hole rolls
TS EN 1965-2 Structural adhesives -Corrosion section 2: Determination and classification of corrosion in brass floor material
TS EN ISO 527-1Plastics-Determination of tensile properties-Part 1: General principles
TS EN ISO 1133-1 Plastics - Determination of the mass flow rate (mfr) and volumetric flow rate (mfr) of molten thermoplastics - Part 1: Standard method
TS EN ISO 1133-2 Plastics - Determination of the mass flow rate (mfr) and volumetric flow rate (mvr) of molten thermoplastics - Part 2: Method for time-temperature history and / or moisture sensitive materials
TS EN ISO 1622-1 Plastics-Polystyrene (PS) molding and extrusion materials-Part 1: Marking system and basic features
TS ISO 124 Rubber latex- Determination of total solids content14.06.2012
TS EN ISO 22007-4 Plastics-Determination of thermal conductivity and thermal diffusivity-Part 4: Laser flash method
TS EN ISO 22007-3 Plastics-Determination of thermal conductivity and thermal diffusivity-Part 3: Temperature wave analysis method
TS EN 12703 Adhesives - for paper, cardboard, packaging and disposable health products - Determination of low temperature flexibility or cold cracking temperature
TS EN 12704 Adhesives for paper, cardboard, packaging and disposable health products - Determination of foam formation for water-based adhesives
tst EN 12012-2 + A2 Tire and plastic machines - Size crushers - part 2: Safety requirements for granulators
TS ISO 10838-3 Polyethylene pipe systems - For the supply of gas fuels - Mechanical fittings section 3: Thermoplastic fittings for pipes with nominal outside diameter equal to or less than 63 mm
TS ISO 7780 Raw rubber and rubber latex - Determination of manganese content - Sodium periodate photometric method
TS ISO 7780 Raw rubber and rubber latex - Determination of manganese content - Sodium periodate photometric method
TS 4709Road vehicles - Rubber elements - For general purposes
TS EN ISO 15605 Adhesives - Sampling
TS EN ISO 9080 Determination of long term hydrostatic strength of plastic pipes and duct systems thermoplastic pipe materials by extrapolation method
TS EN ISO 14855-1 Plastics - Determination of degradation and final aerobic biological degradation under controlled digestion conditions - Method of analysis of released carbon dioxide
TS EN ISO 11357-6 Plastics - Differential scanning calorimetry (dsc) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
TS EN ISO 15015Plastics - Impact-modified acrylonitrile / styrene copolymers (asa, aes, acs) extruded sheets - Properties and test methods
TS EN ISO 527-2 Plastics-Determination of tensile properties-Part 2: Test conditions for molding and extrusion plastics
TS ISO 6194-5 Rotary shaft lip seals - Part 5: Identification of visible defects
TS EN 13900-6 Pigments and additives - Dispersion in plastics and methods for evaluation of dispersion - Part 6: Determination by film test
TS EN ISO 4892-2 Plastics-Methods of exposure to laboratory light sources-Section 2: Xenon arc lamp
TS ISO 7867-1 Tires and wheels for agricultural tractors and machinery (metric series). Chapter 1: Tire designation, dimensions and marking, tire / rim coordination
TS EN ISO 294-5Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 5: Preparation of standard samples for anisotropy investigation
TS EN ISO 1628-1: 2009 / A1 Plastics-Determination of the fluidity of polymers in diluted solutions by capillary viscometer-Part 1: General principles
TS EN ISO 3673-2 Plastics- Epoxy Resins - Part 2: Preparation of Test Samples and Determination of Crosslinked Epoxy Resins
TS EN ISO 11833-1 Plastics - Non-plasticized Polyvinyl Chloride Sheets - Types, Dimensions and Specifications - Part 1: 1 mm. ' Plates Not Thicker Than
TS EN ISO 16014-5 Plastics - Determination of Molecular Mass and Average Molecular Mass Distribution of Polymers by Size Separated Chromatography - Part 5: Determination by Light Distribution Method (Turkish with English Abstract)
TS EN ISO 17556Plastics - Determination of final aerobic biodegradability in soil by measuring oxygen demand or released carbon dioxide in a respirometer
TS EN ISO 1874-2 Plastics - Polyamide (pa) molding and extrusion materials part 2: Preparation of test pieces and determination of their properties
TS EN ISO 11963Plastics - Poly carbonate sheets - Types, dimensions and specifications
TS EN ISO 14129Plastic composites - Fiber reinforced - Determination of in-plane shear stress / shear size change response - ± 45 degree tensile test method including in-plane shear stress / shear modulus
TS EN ISO 14129 Plastic composites - Fiber reinforced - Determination of in-plane shear stress / shear size change response - ± 45 degree tensile test method including in-plane shear stress / shear modulus
TS ISO 6194-4 Rotary shaft lip seals - Part 4: Performance testing procedures
Determination of maximum aerobic biodegradability of plastics under controlled composting conditions - Method of analysis of released carbon dioxide - Part 14855: General method (ISO 1-1: 14855) TS EN ISO 1-2012
TS EN ISO 14855-2 Determination of maximum aerobic biodegradability of plastic materials under controlled composting conditions - Method of analysis of released carbon dioxide - Part 2: Gravimetric measurement of carbon dioxide released in laboratory-level experiment
TS EN ISO 17556Plastics - Determination of the maximum aerobic biodegradability of plastic materials in soil by measuring oxygen demand or the amount of carbon dioxide released by the respirometer
TS ISO 6194-3 Rotary shaft lip seals with elastomeric seals - Part 3: Storage, transport and installation
TS EN 16245-1 Fiber-reinforced plastic composite - Declaration of raw material properties - Part 1: General rules
TS EN 16245-4 Fiber-reinforced plastic composite - Declaration of raw material properties - Part 4: Specific requirements for products
TS EN ISO 178: 2010 / A1 Plastics - Determination of flexural properties
TS EN ISO 14910-1: 2013 Plastics - Thermoplastic polyester / ester and polyether / ester elastomers for molding and extrusion - Part 1: System and principles for marking properties
TS EN ISO 14910-2: 2013 Plastics - Thermoplastic polyester / ester and polyether / ester elastomers for molding and extrusion - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 1856 Flexible, porous, polymeric materials - Determination of crushing rate under pressure
TS 4589 EN ISO 3386-2 / tst A1Flexible and porous polymeric materials in the determination of tensile elongation properties in compression section 2: High-density materials
TS EN ISO 14125 / A1 Fiber reinforced plastic composites - Determination of bending properties
TS EN 26801 / A1Hoses of rubber or plastic - Determination of volumetric expansion
TS EN ISO 4671: 2007 / A1 Rubber and plastic hose and hose assemblies - Methods for measuring the dimensions of hoses and lengths of hose assemblies
TS EN 1114-1 Rubber and plastic machinery-Extruders and extrusion lines-Section 1: Safety rules for extruders
TS EN 12409: 2008 + A1 Rubber and plastic machinery - Thermoforming machines - Safety regulations
TS ISO 4251-3 Tires for agricultural tractors and machinery (marked series with tire tread) and wheels - Part 3: Wheels
TS ISO 188 Tire - Vulcanized or thermoplastic - Accelerated aging and heat resistance tests
TS EN ISO 19712-3 Plastics-Decorative solid surface materials-Part 2: Determination of properties - Solid surface shapes
TS EN 302-6 Adhesives for load-bearing timber - Test methods - Part 6: Determination of conventional compression time
TS EN 302-7 Adhesives for load-bearing timber - Test methods - Part 7: Determination of conventional functional life
TS EN 828 Adhesives-Wettability-Determination by measuring the contact angle and critical surface tension of the solid surface
TS EN 1242 Adhesives - Determination of isosionate content
TS EN 12808-1 Joint fillers - For tiles - Part 1: Determination of the chemical resistance of reaction resin mortars
TS EN 15342 Plastics - Recycled plastics - Characterization of recycled materials from polystyrene (PS)
TS EN 15343 Plastics - Recycled plastics - Plastic recycling traceability and conformity assessment and recycled content
TS EN 15344 Plastics - Recycled plastics - Characterization of recycled materials from polyethylene (PE)
TS EN 15345 Plastics - Recycled plastics - Characterization of recycled materials from polypropylene (PP)
TS EN 15346 Plastics - Recycled plastics - Characterization of poly (vinylchloride) (PVC) recycled materials
TS ISO 4223-1 Definitions of some terms used in the tire industry - Part 1: Pneumatic tires
TS ISO 7867-2 Tires and wheels for agricultural tractors and machinery (metric series) - Part 2: Service description and load ratings
TS ISO 8664 Tires for farm tractors and machinery - Radial drive wheel tires with code designation and service description
TS ISO 4251-1 Tires for agricultural tractors and machinery (series with marked equivalent) and wheels - Part 1: Tire designation, dimensions and approved wheel contours
TS ISO 4251-1 / AMD 1 Tires for agricultural tractors and machinery (series with marked equivalent) and wheels - Part 1: Tire brief designation, dimensions and approved wheel contours
TS ISO 8664 / AMD 1 Tires for farm tractors and machinery - Radial drive wheel tires with code designation and service description Modified 1
TS ISO 4223-1 / AMD1 Definitions of some terms used in the tire industry - Part 1: Modified pneumatic tires 1
TS EN 16240 Light-emitting solid solid polycarbonate (PC) sheets for interior and exterior use on roofs, walls and ceilings-Requirements and test methods
TS EN 13418 Rubber and plastic machinery - Wrapping machines for film or sheet - Safety rules
TS EN 16245-2 Fiber reinforced plastic composite - Declaration of raw material properties - Part 2 - Specific requirements for resin, curing systems, additives and regulators
TS EN 16245-3 Fiber reinforced plastic composite - Declaration of raw material properties - Part 3: Special requirements for fiber
TS EN 16245-5 Fiber-reinforced plastic composite - Declaration of raw material properties - Part 5: special requirements for core materials
TS EN ISO 5999 Polymeric materials - Flexible, porous - Polyurethane foam - for load-bearing applications (excluding undercoverings) - Specification
TS EN ISO 15791-1 Plastics - Development and implementation of medium-sized fire tests for plastic products - Part 1: Inbound guidance
TS EN ISO 306 Plastics-Thermoplastic materials-Determination of Vicat softening temperature (VST)
TS EN 438-9 + A1 Decorative laminated sheets (HPL) - High pressure compression - Thermoset resin based (often called laminated) - Part 9: Classification and specifications for optional laminated laminates
TS EN 14241-1 Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals used in flue linings
TS ISO 7867-2 / AMD 1 Tires and wheels for agricultural tractors and machinery (metric series) - Part 2: Service description and load ratings
TS 6127 EN ISO 4612 Preparation of pastry for plastics-PVC resins
TS ISO 4251-5 / AMD 1 Tires for agricultural tractors and machinery (marked equivalent series) and wheels - Part 5: Loading and forestry service tires REVOLUTION 1
TS EN 12012-3 + A1 Tire and plastic machines - Crushing machines - Part 3: Safety rules for choppers
TS EN 12012-4 + A1 Tire and plastic machines - Size crushers - Part 4: Safety requirements for agglomerators
TS EN 12013 + A1 Rubber and plastic machinery - Internal mixers - Safety regulations
TS EN 12301 + A1 Tire and plastic machines - Calenders - Safety rules
TS EN 13999-1 Adhesives - Short-term method for measuring emission characteristics of adhesives without organic solvent or low content - Part 1: General procedures
TS EN 13999-2 Adhesives - Short-term method for measuring the emission characteristics of adhesives that do not contain or contain low amounts of organic solvents - Part 2: Determination of volatile organic compounds
TS EN 301 Adhesives - Phenolic and aminoplastic - for load bearing wood structures - Classification and performance characteristics
TS ISO 37 Tires and thermoplastics - Tensile stress - Determination of elongation properties
TS ISO 188 Tires - Vulcanized or thermoplastic - Accelerated aging and heat resistance tests
TS EN ISO 1133-1 Plastics - Determination of the mass flow rate (mfr) and volumetric flow rate (mfr) of molten thermoplastics - Part 1: Standard method
TS EN ISO 1133-2 Plastics - Determination of the mass flow rate (MFR) and volumetric flow rate (MVR) of molten thermoplastics - Part 2: Method for time-temperature history and / or moisture sensitive materials
TS EN ISO 11357-6 Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
TS ISO 13442 Tires and wheels for construction equipment
TS EN ISO 11357-5 Plastics - Differential scanning calorimetry (dsc) - Part 5: Determination of trend response time and temperature, reaction enthalpy and degree of conversion
TS EN ISO 11357-2 Plastics - Differential scanning calorimetry (dsc) - Part 2: Determination of glassization temperature and glassization step height
TS EN ISO 472 Plastics-Terms and recipes
TS EN 14933 Thermal insulation products and lightweight fillers - For civil engineering applications - Fabricated products of expanded polystyrene (EPS) - Specification
TS ISO 4251-4 Tires for agricultural tractors and machinery (marked series) and wheels - Part 4: Tire classification and naming
TS EN ISO 12162 Thermoplastic materials - For pipes and fittings used in pressure-applied situations - Classification and marking - Total service coefficient
TS 4651 EN 25978 Rubber or plastic coated fabrics - Determination of adhesion strength between surfaces
TS 6757 EN ISO 2556 Plastics-Determination of gas permeability of films and thin sheets under atmospheric pressure - Manometric method
TS EN 15534-1 Composites made of cellulose-based material and thermoplastic (commonly known as wood-polymer composite (WPC) or natural fiber composites (NFC)) - Part 1: Test methods for the characteristics of the product and its components
TS EN 15534-1 Composites made of cellulose-based material and thermoplastic (commonly known as wood-polymer composite (WPC) or natural fiber composites (NFC)) - Part 1: Test methods for the characteristics of the product and its components
TS EN 15534-4 Composites made of cellulose-based material and thermoplastic (commonly known as wood-polymer composite (WPC) or natural fiber composites (NFC)) - Part 4: Specifications for deck profiles and tiles
TS EN 15534-5 Composites made of cellulose-based material and thermoplastics (commonly known as wood-polymer composites (WPC) or natural fiber composites (NFC)) - Part 5: Specifications for coating profiles and tiles
TS EN ISO 1183-1 Plastics - Density determination methods of nonporous plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1: 2012)
TS EN 12645: 2014 Pressure gauges - Equipment for pressure testing and / or inflation of motor vehicle tires - Measuring technique, specifications and tests
TS EN 289 Plastic and rubber machines - Presses - Safety regulations
TS EN 28510-1 Adhesives - Peel test of two specimens, one flexible and one rigid, bonded to each other - Part 1: Stripping test at 90 ° angle
TS ISO 4251-1 / AMD 1 Tires for agricultural tractors and machinery (series with marked equivalent) and wheels - Part 1: Tire brief designation, dimensions and approved wheel contours
TS EN ISO 877-1Plastics - Methods of exposure to sunlight - Part 1: General rules
TS EN ISO 877-3Plastics - Methods of exposure to sunlight - Part 3: Intensified sunlight
TS EN ISO 10352 Fiber reinforced plastics - Molding mixtures and prepregs - Determination of unit area mass
TS ISO 4223-1 Definitions of some terms used in the tire industry - Part 1: Pneumatic tires
TS ISO 4223-1 / AMD1 Definitions of some terms used in the tire industry - Part 1: Pneumatic tires
TS ISO 4250-1 Tires and wheels for construction and excavation machinery - Part 1: Tire designation and dimensions
TS EN 16472 Plastics - Accelerated artificial method of aging using Medium Pressure Mercury Vapor Lamps
TS EN ISO 20753Plastic material - Test specimens
TS EN ISO 6427 Plastics - Determination of substances which can be extracted with organic solvents (routine methods)
TS EN ISO 10350-1 / A1 Plastics - Accumulation and presentation of comparable single note data section 1: Molding materials
TS EN ISO 11357-4 Plastics - Differential scanning calorimetry (dsc) - Part 4: Determination of specific heat capacity
TS EN ISO 11403-1 Plastics-Collection and presentation of comparable multiple data-Part 1: Mechanical properties
TS EN ISO 11403-3 Plastics - Collection and presentation of comparable multiple data - Part 3: Environmental impacts on properties
TS EN ISO 3385 Flexible porous polymeric materials - Determination of fatigue properties under repeated constant loads
TS EN ISO 3949 Plastic hoses and hose assemblies. -Specific types of textile reinforced for hydraulic applications
TS EN ISO 4895 Plastics-Liquid epoxy resins-Determination of crystallization tendency
TS EN ISO 6808 Plastic hoses and hose assemblies - Used for suction and discharge at low pressure - For petroleum based liquids - Specifications
TS EN 15345 Plastics - Recycled plastics - Characterization of recycled components from polypropylene (pp)
TS EN 15347 Plastics - Recycled plastics - Characterization of plastic waste
TS EN 15347 Plastics - Recycled plastics - Characterization of plastic waste
TS EN 12645 Tire pressure gauges - Devices for the pressure testing and / or inflating / lowering of motor vehicle tires - Measuring technique, rules and tests
TS EN 15752-1 Glass for buildings - One-side self-adhesive polymeric film - Part 1: Definitions and requirements
TS EN 15755-1 Glass for buildings - One side self-adhesive polymeric film - Part 1: Definitions and requirements
TS ISO 5751-3 Motorcycle tires and wheels (metric series) - Part 3: Range of approved wheel contours
TS ISO 4251-4 Tires for agricultural tractors and machinery (marked series) and wheels - Part 4: Tire classification and naming
TS EN 15344 Plastics - Recycled plastics - Characterization of recycled components from polyethylene (pe)
TS EN 15345 Plastics - Recycled plastics - Characterization of recycled components from polypropylene (pp)
TS EN 438-8 Decorative laminated sheets - High pressure compressed (hpl) - Thermoset resin based (often called laminated) - Part 8: Classification and specifications for design laminates
TS EN ISO 9012 Gas welding device-Air suction hand torches-Features and tests
TS EN ISO 6806 Rubber hoses and hose assemblies-Features used in liquid fuel burners
TS EN ISO 2440 / A2 Flexible and hard porous polymeric materials - Accelerated aging tests
TS EN ISO 17855-1 Plastics - Polyethylene (PE) molding and extrusion materials - Part 1: Description system and basic technical characteristics
TS EN ISO 19066-1 Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) molding and extrusion materials - Part 1: Description system and technical characteristics
TS EN ISO 9012 Gas welding device-Air suction hand torches-Features and tests
TS EN ISO 3861 Rubber hoses - Specification for sand and sand blasting
TS ISO 4000-1 Passenger car tires and wheels - Part 1: Tires (metric series)
TS ISO 4251-5 Tires for agricultural tractors and machinery (series with marked equivalent) and wheels - Part 5: Loading and forestry service tires
TS ISO 4251-5 / AMD 1 Tires for agricultural tractors and machinery (equivalent to marked series) and wheels - Part 5: Loading and forestry service tires
TS ISO 8013 Rubber, vulcanized - Determination of creep or shear under pressure
TS ISO 8404 Pins - Angular - Basic dimensions18.02.2015
TS ISO 4000-1 Tires and wheels for passenger cars - Part 1: Tires (metric series)
TS EN 1013 + A1 Transparent, single-layer, plastic-profile sheets for use in roofs, walls and ceilings indoors and outdoors - Requirements and test methods
tst EN 15534-5 Composites made of cellulose-based material and thermoplastics (commonly known as wood-polymer composites (WPC) or natural fiber composites (NFC)) - Part 5: Specification for cladding profiles and tiles
TS EN 301 Adhesives - Phenolic and aminoplastic - For load bearing wood structures - Classification and performance characteristics
TS EN ISO 291 Plastics - Standard atmospheric conditions for conditioning and testing
TS EN 1417 Rubber and plastic machinery - Rollers with two rollers - Safety rules
TS ISO 2781 Vulcanized rubber - Determination of density
TS EN 15346 Plastics - Recycled plastics - Characterization of recycled components from poly (vinyl chloride)
TS EN 15348 Plastics - Recycled plastics - Characterization of recycled components from poly (ethylene terephthalate)
TS EN ISO 18064Termoplastic elastomers - Terms and abbreviations
TS EN ISO 19065-1 Plastics - Acrylonitrile Styrene Acrylate (ASA), Acrylonitrile (ethylene, propylene, diene) Styrene (AEPDS) and acrylonitrile (chlorinated polyethylene) styrene (ACS) casting and extrusion materials - Part 1: Marking system and basic features
tst ISO 8013 Rubber, vulcanized - Determination of creep or shear under pressure
TS ISO 3601-1 Rubber rings in fluid systems, inner diameters, cross sections, tolerances and nominal size
TS ISO 3601-Cor 1 Rubber rings in fluid systems with internal diameters, cross-sections, tolerances and nominal size
TS ISO 12176-4 Plastic pipes and fittings - Equipment for polyethylene systems with melting connection - Part 4: Conformity coding
TS ISO 1817 Tires-Determination of the effect of liquids
TS EN 15752-1 Glass for buildings - One-side self-adhesive polymeric film - Part 1: Definitions and requirements
TS EN 15755-1 Glass for buildings - One side self-adhesive polymeric film - Part 1: Definitions and requirements
TS ISO 8873-2 Rigid porous-Plastics-Spray-applied polyurethane foam section for thermal insulation processes 2: Applications
tst EN 15534-1 Composites made of cellulose-based material and thermoplastics (commonly known as wood-polymer composites (WPC) or natural fiber composites (NFC)) Section 1: Test method for characteristics of products and components
tst EN 15534-1 Composites made of cellulose-based material and thermoplastics (commonly known as wood-polymer composites (WPC) or natural fiber composites (NFC)) Section 1: Test method for characteristics of products and components
TS EN ISO 19069-1 Plastics-Polypropylene (pp) molding and extrusion materials-Part 1: Principles for marking system and features
TS EN ISO 22007-6 Plastics - Determination of thermal conductivity and thermal diffusivity - Part 6: Comparative method using temperature-modulation technique for low thermal conductivity
TS ISO 5751-3Motorcycle tires and wheels (metric series) - Part 3: Approved wheel contour range
TS EN ISO 306Plastics-Thermoplastic substances - Determination of Vicat softening temperature (VST)
TS EN ISO 527-1Plastics - Determination of tensile properties - Part 1: General principles
TS EN ISO 527-2Plastics-Determination of tensile properties-Part 2: Test conditions for molding and extrusion plastics
TS EN ISO 3949 Plastic hoses and hose assemblies - Textile reinforced types for hydraulic applications - Specification
TS EN ISO 4895Plastics-Liquid epoxy resins-Determination of crystallization tendency
TS EN 16153 + A1Polycarbonate (PC) flat sheets - Transparent - Closed corrugated (with chamber) - Used in roofs, walls and ceilings indoors and outdoors - Requirements and test methods
TS EN ISO 16396-1 Plastics - Polyamide (pa) molding and extrusion materials - Part 1: Display system, marking of products and principles for properties
TS ISO 12000 Plastics / rubber - Polymer dispersions and rubber latexes (natural and synthetic) - Definitions and examination of test methods
TS ISO 6072 Rubber - Compatibility between hydraulic fluids and standard elastomeric materials
TS ISO 2321 Rubber yarns - Test methods
TS ISO 6601 Plastics - Shear friction and wear - Determination of test parameters
TS EN ISO 1043-1 Plastics-Symbols and abbreviated terms-Part 1: Main polymers and their special characteristics
TS EN ISO 1043-2 Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials
TS ISO 3601-1 Rubber rings in fluid systems, inner diameters, cross sections, tolerances and nominal size
TS ISO 3601-Cor 1 Rubber rings in fluid systems with internal diameters, cross-sections, tolerances and nominal size
TS EN ISO 20753 Plastics - Test specimens 26.11.2015 83.080.01
TS EN ISO 11357-5 Plastics - Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic reaction temperatures and durations, reaction enthalpy and degree of conversion
TS EN ISO 11357-2 Plastics - Differential scanning calorimetry DSC) - Part 2: Determination of glass transition temperature and glass transition step height
TS EN ISO 3167 Plastics - Multi-purpose test specimens
TS EN 1013 + A1 Transparent, single-skinned, corrugated plastic sheets for roofing, walls and ceilings indoors and outdoors - Requirements and test methods
TS EN ISO 9311-2 Adhesives for thermoplastic pipe systems - Part 2: Determination of shear strength
TS ISO 6117 Road vehicles - Elastomer dust holding tires for drum hydraulic wheel brake cylinders with non-petroleum-based hydraulic brake fluid (operating temperature up to 100 0C)
TS ISO 6119 Road vehicles - Elastomer seals - For hydraulic disc brake cylinders using non-petroleum-based hydraulic brake fluid (operating temperature up to 120 c)
TS ISO 3739-1 Industrial tires and wheels section 1: Air tires on highly tapered or flat bottom wheels (metric series) - Designation, dimensions and markings
TS ISO 20562 Wheel tire valves - ISO housing holes no. 1, no.2 and no.3
TS ISO 4927 Road vehicles - Elastomeric dust holding tires for drum braking systems - For wheel brake cylinders using non-oil based hydraulic brake fluid (operating temperature up to 120 ° c)
TS ISO 6916-1 / A1 Flexible, porous polymeric materials - Sponge and expanded porous rubber products - Specification - Part 1: Sheets
TS ISO 6472 Rubber compound additives - Abbreviations
TS ISO 7663 Evaluation of the vulcanization properties of halogenated isobutene-isoprene rubber (BIIR, CIIR)
TS ISO 1926 Rigid porous plastics - Determination of tensile properties
TS ISO 9772 Porous plastics - Determination of the combustion properties of small test specimens exposed horizontally to a small flame
TS ISO 12000 Plastics / rubber - Polymer dispersions and rubber latexes (natural and synthetic) - Definitions and examination of test methods
TS EN ISO 11403-2 Plastics - Collection and presentation of comparable data - Part 2: Thermal and processing properties
TS EN ISO 1183-1 Plastics - Density determination methods of nonporous plastics - Part 1: Immersion method, liquid pyknometer method and titration method
TS EN ISO 5659-2 Plastics - Smoke formation - Part 2: Determination of optical density by a single chamber test
TS ISO 6804 Rubber and plastic hose and hose sets for washing and dishwashing machines - Specifications
TS ISO 7267-3 Rubber coated rollers - Determination of apparent hardness - Part 3: Pusey and Jones method
TS ISO 4649 Tires - vulcanized or thermoplastic - Determination of abrasion resistance by means of a rotating cylindrical drum
TS ISO 7267-2 Rubber coated rollers - Determination of apparent hardness - Part 2: Shore-type durometer method
TS ISO 6118: 2006 Elastomeric cups and seals for cylinders for hydraulic brake systems using a non-oil base hydraulic brake fluid - Road vehicles (service temperature 70 ° C max.)
TS ISO 13007-1 Ceramic tiles - Sorbets and binders - Part 1: Terms, descriptions and specifications for binders
TS ISO 13007-2 Ceramic tiles - Sorbets and binders - Part 2: Test methods for binders
TS ISO 13007-5 Ceramic tiles - Sorbets and binders - Part 5: Requirements, test methods, conformity assessment and brief demonstration of waterproofing membranes applied as binders under the bonded ceramic tile
TS EN ISO 22007-1 Plastics-Determination of thermal conductivity and thermal diffusion-Part 1: General rules
TS EN ISO 28017Flexible hoses and hose assemblies, wire or textile reinforced, for screening applications
TS ISO 1663 Porous plastics - Determination of water vapor permeability rate of rigid materials
TS 9220 EN 26801 (Number Amendment TS EN 26801: 1993) Rubber and plastic hoses-Determination of volumetric expansion
TS EN ISO 7823-2 / tst T1 Plastics - Poly (methyl methacrylate) sheets - types, dimensions and specifications - Part 2: Extruded sheets
TS EN ISO 1825 Rubber hoses and hose assemblies - Used for filling and discharging of fuel in the ground in aviation - Specifications
TS EN ISO 1043-1 Plastics - Symbols and abbreviated terms - Part 1: Main polymers and their special characteristics
TS EN ISO 1043-2 Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials
TS EN ISO 1043-2 Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials
TS ISO 4570 Tire wheel valve threads
TS EN ISO 6383-1 Plastics - Film and sheets - Determination of tear strength - Part 1: Pantalon type tear method
TS EN ISO 16012Plastics - Determination of linear dimensions of test specimens
TS EN 16795 Plastics - Method for determining the heat accumulation of flat surfaces by simulated solar radiation
TS EN 438-1 Decorative laminated sheets (hpl) - High pressure compression - Thermoset resin based - Part 1: Introduction and general information
TS EN 438-3 Decorative laminated sheets (hpl) - High pressure compacted - Thermoset resin based (often called laminated) - Section 3: Classification and specifications for laminated sheets thinner than 2 mm designed for bonding to supporting substrates 24.03.2016 83.140.20
TS EN 438-4 Decorative laminated sheets (hpl) - High pressure compression - Thermoset resin based (often called laminated) - Part 4: 2 24.03.2016 83.140.20 XNUMX classification and specifications for tight laminated sheets
TS EN 438-5 Decorative laminated sheets (hpl) - High pressure compression - Thermoset resin based (often referred to as laminated) - Part 5: Classification and specifications for 2 mm thin flooring class laminated sheets designed for bonding to supporting substrates 24.03.2016 83.140.20
TS EN 438-6Decorative laminated sheets (hpl) - High pressure compression - Thermoset resin based (often referred to as laminated) - Part 6: Classification and specifications for 2 mm and thicker laminated sheets for outdoor use 24.03.2016 83.140.20
TS ISO 4251-5 Tires for agricultural tractors and machinery (marked series) and wheels - Part 5: Skid tires
tst ISO 4251-2 wheels for farm tractors and heavy equipment - Part 2: Tire load rating
TS ISO 8053 Rubber and latex - Determination of copper content - Photometric method18.02.2016
TS ISO 2558 Determination of the time of dissolution of the adhesive in styrene in glass mats made of glass fiber used for reinforcing plastics
TS ISO 4635 Tires-Preformed joint fillers-For joints between concrete pavements on highways
TS ISO 7323 Tires - Raw and vulcanized rubber pulp - Determination of plasticity and return number - Parallel plate method
TS ISO 7323 Tires - Raw and vulcanized rubber pulp - Determination of plasticity and return number - Parallel plate method
TS ISO 11235 Rubber pulp additives - Sulfenamide accelerators - Test methods
TS ISO 1138 Rubber pulp additives - Carbon black - Determination of sulfur
TS ISO 1138 / A1 Rubber pulp additives - Carbon black - Determination of sulfur - Clarification of decomposition temperature in 3.4.5 subheading
TS ISO 871 Plastics - Determination of ignition temperature using hot air furnace
TS ISO 2230 Rubber products - Storage rules
TS ISO 1853 Conductive and damping rubber, vulcanized or thermoplastic - Measurement of resistivity
TS EN ISO 11357-7 Plastics- Differential scanning calorimetry (dsc) - Part 7: Determination of crystallization kinetics
TS EN ISO 20200 Plastics - Determination of the degree of disintegration of plastic materials under conditions of decomposition simulated by laboratory scale testing
TS EN 59 Glass fiber reinforced plastics - Determination of hardness by Barcol hardness tester
TS EN 14680 Plastic pipe systems - Adhesives for non-pressurized thermoplastic pipe systems - Specifications
TS EN 923 Adhesives - Terms and recipes
TS EN ISO 4892-3 Plastics-Methods of exposure to laboratory light sources-Section 3: Fluorescent uv lamps
TS EN 16254 + A1 Adhesives - Polymerized isocyanate emulsion (PIE) - For wood structures exposed to load - Classification and performance requirements
TS EN 14814 Adhesives for thermoplastic pipe systems for pressurized fluids - Specifications
TS EN ISO 17855-2 Plastics - Polyethylene (PE) molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties (ISO 17855-2: 2016)
TS EN ISO 19069-2 Plastics - Polypropylene (PP) molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties (ISO 19069-2: 2016)
Plastics - Symbols and abbreviated terms - Part 1043: Main polymers and their special characteristics TS EN ISO 1-1 / A1
TS EN ISO 4892-1 Plastics-Methods of exposure to laboratory light sources-Section 1: General guide
Plastics - Symbols and abbreviated terms section 1043: Flame retardants TS EN ISO 4-1999: 1 / A4 Plastics
Plastics - Symbols and abbreviated terms section 1043: Flame retardants TS EN ISO 4-1999: 1 / A4 Plastics
TS EN 16661 Motor vehicles and tire pressure gauges (TPG) - Interoperability of TIS and TPG - Interfaces and requirements
TS EN ISO 177 Plastics-Determination of plasticizer transition
TS EN 15416-1 Adhesives other than phenolic and aminoplastics for load bearing timber structures - Test methods - Part 1: Long-term tensile load test perpendicular to the bonding line under varying climatic conditions with specimens perpendicular to the bonding line
TS EN 15416-3 Adhesives other than phenolic and aminoplastics for load bearing timber structures - Test methods - Part 3: Creep deformation test of specimens under flexural shear in cyclic climatic conditions
TS EN 302-8 Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond specimens in compression shear
TS EN 15416-4 Adhesives other than phenolic and aminoplastics for load bearing timber structures - Test methods - Part 4: Determination of open bonding time under reference conditions
TS EN ISO 19712-2 Plastics-Decorative solid surface materials-Part 2: Determination of properties - Sheet products
TS EN ISO 75-1 Plastics - Determination of bending temperature under load - Part 1: General test method
TS EN ISO 75-2 Plastics- Determination of bending temperature under load- Part 2: Plastics and ebonite
TS EN ISO 180: 2000 / A2Plastics-Determination of Izod impact strength
Plastics - Polyamides - Determination of viscosity number TS EN ISO 307: 2007 / A1: 2013
TS EN 438-2 Decorative laminated sheets (hpl) - High pressure compressed - Thermoset resin based section 2: Determination of properties
TS EN 15534-6 Composites made of cellulose-based material and thermoplastic (commonly known as wood-polymer composite (WPC) or natural fiber composites (NFC)) - Part 6: Specification for fence profiles and elements
TS EN 16465 Plastics - Calibration of black standard and white standard thermometers and black panel and white panel thermometers used in natural and artificial weather conditions
TS EN ISO 19062-1 Plastics - Acrylonitrile-Butadiene-Styrene (abs) molding and extrusion materials - Part 1: Guidelines for marking system and properties
TS EN ISO 19064-1 Plastics - Styrene / acrylonitrile (SAN) molding and extrusion materials - Part 1: System and principles for marking properties
TS EN ISO 19063-1 Plastics - Impact-resistant polystyrene (PS-I) molding and extrusion materials - Part 1: The basics on which marking system and features are based
TS ISO 4250-2 Construction and excavation machinery tires and wheels - Part 2: Loads and inflation pressures
TS EN ISO 11357-1 Plastics - Differential scanning calorimetry (dsc) - Part 1: General principles
TS EN ISO 1043-3 Plastics-Symbols and abbreviated terms-Part 3: Plasticizers
TS EN ISO 1043-3 Plastics-Symbols and abbreviated terms-Part 3: Plasticizers
TS EN 13206: 2017 Thermoplastic coating films-used in horticulture
TS ISO 13226 Rubber - Standard reference elastomers (SRE) that characterize the effect of liquids on vulcanized rubbers
TS EN 542 / T1 Adhesives - Determination of density
TS EN ISO 15527Plastics - Mold compression of polyethylene sheets - Requirements and test methods
TS EN 302-1 Adhesives for load-bearing timber structures - Test methods - Part 1: Determination of shear strength in longitudinal tensile
TS EN 302-2 Adhesives for load-bearing wooden structures - Test methods - Part 2: Determination of resistance to separation
TS EN 302-3 Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage on transverse tensile strength to wood fibers by temperature and humidity cycle
TS EN 302-4 Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effect of wood shrinkage on shear strength
TS EN 12090 Thermal insulation materials - For buildings - Determination of slip properties
TS EN 12091 Thermal insulation materials - For buildings - Freezing - Determination of thaw resistance
tst EN ISO 179-1 Plastics - Determination of Charpy impact properties - Part 1: Impact test without impression
tst EN 13206 Thermoplastic coating films-Used in horticulture and agriculture
tst EN ISO 5359Anesthesia and breathing apparatus - Low pressure hose fittings for use with medical gases
TS 9955Plastic pipes - Determination of external load resistance properties - Parallel plates method
TS ISO 4251-1: 2005 Tires for agricultural tractors and machinery (series with marked equivalent) and wheels - Part 1: Tire designation, dimensions and approved wheel contours
TS ISO 4250-1 Tires and wheels for construction and excavation machinery - Part 1: Tire designation and dimensions
TS EN ISO 5359 Anesthesia and breathing equipment - Low pressure hose fittings for use with medical gases
TS EN ISO 4590: 2016 Porous, rigid plastics - Determination of volume percentage of open and closed pores
tst EN 16153 + A1Polycarbonate (PC) flat sheets - Transparent - Closed corrugated (with chamber) - Used in roofs, walls and ceilings indoors and outdoors - Requirements and test methods
TS EN 12608-1 Rigid polyvinylchloride (pvc-U) profiles - Used in fabrication of windows and doors - Classification, properties and test methods
TS EN 12608-1 Rigid polyvinylchloride (pvc-U) profiles - Used in fabrication of windows and doors - Classification, properties and test methods
TS EN ISO 1401 Rubber hoses for agricultural spraying
TS EN ISO 15512Plastics - Determination of water content
TS EN 15701 Plastics - Thermoplastic liners for insulation products of building equipment and industrial insulation
TS EN ISO 11469 Plastics - Group identification and marking of plastics
Biological based carbon content - Determination of biocompatible carbon content by using radiocarbon method
TS EN ISO 11358-1 Thermogravimetry of plastics - polymers - Part 1: General principles
TS EN ISO 844 Hard porous plastics - Determination of compression properties
TS EN ISO 3167 Plastics - Multi-purpose test pieces
TS EN 15347 Plastics - Recycled plastics - Characterization of plastic waste
TS EN 438-9 + A1 Decorative laminated sheets – High pressure compacted (HPL) esaslıThermocet resin based (often called laminated) - Part 9: Classification and specifications for alternative body laminates
TS ISO 4643 Shoes, plastic - Lining or uncoated poly (vinyl chloride) boots for general industry - Technical Specifications
TS EN 12004-1 Adhesives for ceramic tiles - Part 1: Requirements, assessment and verification of performance continuity, classification and marking
TS EN 12004-2 Adhesives for ceramic tiles - Part 1: Test methods
TS EN ISO 25137-1 Plastics - Sulfon polymer molding and extrusion materials - Part 1: Identification system and the basis of specifications
TS EN ISO 25137-2 Plastics - Sulfon polymer molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 29664Plastics - Artificial wind test including acidic deposition
TS EN ISO 16396-2 Plastics - Polyamide (pa) molding and extrusion materials part 2: Preparation of test pieces and determination of their properties
TS EN ISO 20028-1 Plastics - Thermoplastic polyester (tp) molding and extrusion materials - Part 1: Basics for marking system and features
TS EN ISO 20028-2 Plastics - Thermoplastic polyester (tp) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS ISO 48 Rubber-Vulcanized or thermoplastic-Hardness determination (10 armor-100 armor hardness range)
TS ISO 37 Tires and thermoplastics - Tensile stress - Determination of elongation properties
TS EN 14241-1 Chimneys - Elastomeric seals and elastomeric seals - Material requirements and test methods - Part 1: Seals used in chimney linings
TS EN 16556 Longest open time determination for thermoplastic wood adhesives used in non-structural applications
TS EN 15307 Adhesives - For leather and shoe materials - Claw top adhesions - Minimum strength requirements
TS EN 1372 Adhesives - Test method for adhesives for floor coverings and wall coverings-Stripping test
TS EN 1373 Adhesives - Test methods for adhesives for floor coverings and wall coverings - Slip test
TS EN 15274 General purpose adhesives for structural joints - Properties and test methods
TS EN 15275 Structural adhesives - Properties of anaerobic adhesives for coaxial metallic joints in civil engineering structures and buildings
TS EN 1902 Adhesives - Test methods for adhesives used in floor coverings and wall coverings - Slip test
TS EN 1903 Adhesives - Test methods for adhesives used for plastic or rubber, floor or wall coverings - Determination of size changes after accelerated aging
TS ISO 2921 Vulcanized rubber - Determination of low temperature shrinkage (TR test)
TS EN ISO 13894-1 Decorative laminated sheets - High pressure compression - Composite elements - Part 1: Test methods
TS EN ISO 13894-2 Decorative laminated sheets - High pressure compression - Composite elements - Part 2: Specification for wood-based base material composite elements for indoor use
TS ISO 13927 Plastics - Simple determination of heat generated by conical radiant heaters and thermopile detectors
TS EN ISO 13802 Plastics - Verification of pendulum impact tester - Charpy, isod and tensile impact test
TS EN ISO 21509Plastics and ebonite - Shore durometer verification
TS EN ISO 22007-2 Plastics - Determination of thermal conductivity and thermal diffusivity - Part 2: Temporary flat and heat source (hot disc) method
TS EN 13986: 2004 + A1 Wood-based panels used in buildings - Characteristics, evaluation of conformity and marking
TS EN ISO 899-2 / A1 Plastics - Determination of creep property - Part 2: Flexural strength in three-point loading - Amendment 1
TS EN ISO 899-1 / A1 Plastics - Determination of creep properties - Part 1: Tensile creep - Modified 1
TS EN ISO 28017 / A1 Rubber hoses and hose assemblies, reinforced by wire or textile, for screening applications - Specifications - Amendment 1
TS EN ISO 1628-5 Plastics - Determination of viscosity in dilute solutions of polymers using capillary viscometers - Part 5: Thermoplastic polyester (tp) homopolymers and copolymers
TS EN ISO 9988-2 Plastics - Polyoxymethylene (pom) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN 302-5 Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of the longest representation time under reference conditions
TS EN 15416-5 Adhesives other than phenolic and aminoplastics for load bearing timber structures - Test methods - Part 5: Determination of minimum compression time under reference conditions
TS EN 15425 Adhesives - Single component polyurethane for load bearing timber structures - Classification and performance characteristics
TS ISO 34-2 Tires or thermoplastics - Determination of tear strength - Part 2: Small (delft) test pieces
TS ISO 7270-1 Tires - Pyrolytic gas analysis - chromatographic methods - Part 1: Identification of polymers (single polymers and mixtures)
tst ISO 3934 Vulcanized and thermoplastic tires - Preformed gaskets for construction - Classification, determination and testing methods
TS ISO 3934 Vulcanized and thermoplastic tires - Preformed gaskets for construction - Classification, determination and test methods
TS ISO 7270-1 / A1 Tires - Pyrolytic gas analysis - chromatographic methods - Part 1: Identification of polymers (single polymers and mixtures)
TS ISO 7270-2 Tires - Pyrolytic gas analysis - chromatographic methods - Part 2: Determination of styrene / butadiene / isoprene ratio
TS ISO 6721-4 Plastics- Determination of dynamic mechanical properties- Part 4: Stress vibration- Non-resonance method
TS ISO 6721-5 / A1 Plastics- Determination of dynamic mechanical properties- Part 5: Bending vibration- Resonance-free method
TS ISO 6721-6 / A1 Plastics - Determination of dynamic mechanical properties - Part 6: Shear vibration - Resonance free method
TS ISO 6721-7 / A1 Plastics - Determination of dynamic mechanical properties - Part 7: Torsional vibration - Resonance-free method
TS ISO 6721-9 / A1 Plastics - Determination of dynamic mechanical properties - Part 9: Stress vibration - Propagation of sound waves
TS ISO 2006-1 Synthetic rubber latex - Determination of mechanical stability - Part 1: High speed method
TS ISO 2006-2 Synthetic rubber latex - Determination of mechanical stability - Part 2: Medium speed method under load
TS ISO 12965 / Cor 1 Butadiene rubber - Determination of microstructure by infrared spectrometric method
TS ISO 16565 Determination of 5-Ethylidene norbornene (enb) or dicyclopentadiene (dcpd) in rubber-ethylene-propylene-diene (epdm) terpolymers
TS ISO 4666-2 Tires-Determination of temperature rise and fatigue resistance by flexometer test-Part 2: Rotary flexometer
TS ISO 4666-3 Tires-Determination of temperature rise and fatigue resistance with flexometer test-Part 3: Compression flexometer
TS ISO 4666-1 Tires - Determination of temperature rise and fatigue resistance by flexometer test - Part 1: Basic principles
TS ISO 4666-4 Tires - Determination of temperature rise and fatigue resistance by flexometer test - Part 1: Basic principles
TS ISO 8789 Rubber hoses and hose assemblies - for liquefied petroleum gas used in motor vehicles
TS ISO 8796 Polyethylene PE 32 and PE 40 pipes - For irrigation channels - Sensitivity to circumferential stress cracking caused by plug-in fittings - Test method and features
TS ISO 6123-1 Rollers - Rubber or plastic coated - Hardness requirements for materials used in roll coating
TS ISO 6123-2 Rollers - Rubber or plastic coated - Surface properties
TS ISO 14960-1: 2014 Tubeless tires - Valves and components - Part 1: Test methods
TS ISO 22196 Plastics - Measurement of antibacterial mobility on plastic surfaces
TS EN ISO 10724-1 Plastics - Preparation of test pieces by injection molding from thermoset powder molding mixtures - Part 1: General principles and molding of multi-purpose test pieces
TS ISO 36 Determination of adhesion to rubber-vulcanized or thermoplastic-textile fabrics
TS EN 40-7 Lighting poles - part 7: Requirements for fiber-reinforced polymer composite lighting poles
TS EN ISO 62 Plastics-Determination of water absorption
TS EN ISO 75-3Plastics- Determination of bending temperature under load- Part 3: High-strength thermoset laminates and long-fiber reinforced plastics
TS EN ISO 75-3 Plastics - Determination of bending temperature under load - Part 3: High strength thermoset laminates and long-fiber reinforced plastics
TS EN ISO 75-3 / AC Plastics - Determination of bending temperature under load - Part 3: High strength thermoset laminates and long-fiber reinforced plastics
TS EN ISO 75-3 / AC Plastics - Determination of bending temperature under load - Part 3: High strength thermoset laminates and long-fiber reinforced plastics
TS ISO 123 Rubber latex-Sampling
TS ISO 132 Determination of rubber-vulcanized or thermoplastic-bending cracking and crack growth (de mattia)
TS EN ISO 175: 2010 Plastics - Determination of the effects when immersed in liquid chemicals - Test methods
TS EN ISO 176 Plastics-Determination of plasticizer loss, activated carbon method
TS EN ISO 179-1Plastics - Determination of Charpy impact properties-Part 1: Impact-free impact test
TS EN ISO 179-2 Plastics-Determination of charpy impact properties-Part 2: Impact test with measuring instrument
TS EN ISO 180 Plastics - Determination of Izod impact strength
TS EN ISO 180 / A1 Plastics - Determination of Izod impact strength
TS 189 ISO 171 Plastics - Molding materials - Batch factor determination
TS EN 201 Rubber and plastic machinery - Injection molding machines - Safety rules
TS EN 205 Adhesives - Wood adhesives for non-structural applications - Determination of tensile shear strength of overlap glued joints
TS EN 263 Sanitary ware - Cross-linked cast acrylic sheets for bath tubs and shower trays for domestic use
TS ISO 7269 Tech.Corr.1 Tires - Determination of free sulfur
TS EN ISO 293 Plastics - Preparation of test pieces from thermoplastic materials by pressure molding
TS EN ISO 294-2 / A1 Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 2: Small draw bars
TS EN ISO 294-1 / A1 Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 1: General principles and molding of multi-purpose rod test pieces
TS EN ISO 294-3Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 3: Small plates
TS EN ISO 294-4Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 4: Determination of shrinkage in mold
TS EN ISO 295 Plastics - Thermoset materials - Preparation of test pieces by pressure molding
TS 333 ISO 125 Natural rubber latex concentrates - Determination of base
TS 335 ISO 127 Rubber, natural latex concentrate - Koh number determination
TS 336 ISO 247 Rubber - Determination of ash
TS 337 ISO 248Rubber, Determination of volatile substances
TS 339 EN ISO 120 Plastics - Phenol formaldehyde molded parts - Determination of free ammonia and ammonium compounds -Colorimetric comparison method
TS 357 EN ISO 119 Plastics - Phenol formaldehyde molded parts - Determination of free phenols - Iodometric method
TS 360 ISO 249 Raw, natural rubber-Determination of foreign matter
TS EN 422 Safety in machines - Rubber and plastic machinery - Safety - Design and construction rules for blow molding machines for the production of hollow bodies
TS 448 EN ISO 60 Plastics - Determination of apparent density of materials that can be flowed from a particular funnel
TS 449 EN ISO 61 Plastics - Determination of apparent density of non-pourable plastic molding materials from a particular funnel
TS EN 477 Unplasticized polyvinylchloride (pvc-U) profiles used in the manufacture of windows and doors - Determination of impact strength in main profiles - Mass reduction method
TS EN 477 Unplasticized polyvinylchloride (pvc-U) profiles used in the manufacture of windows and doors - Determination of impact strength in main profiles - Mass reduction method
TS EN 478 Unplasticized polyvinylchloride (pvc-U) profiles used in the manufacture of windows and doors, appearance after exposure to 150 c - Test method
TS EN 478 Unplasticized polyvinylchloride (pvc-U) profiles used in the manufacture of windows and doors, appearance after exposure to 150 c - Test method
TS EN 479 Non-plasticizing polyvinyl chloride (pvc-U) profiles used in the manufacture of windows and doors - Determination of permanent thermal elongation
TS EN 479 Non-plasticizing polyvinyl chloride (pvc-U) profiles used in the manufacture of windows and doors - Determination of permanent thermal elongation
TS ISO 498 Rubber latex concentrate - Preparation of dry films
TS EN 513 Non-plasticizing polyvinylchloride (pvc-U) profiles used in window and door manufacturing - Determination of resistance to artificial weather conditions
TS EN 514 Non-plasticizing polyvinylchloride (pvc-U) profiles used in window and door manufacturing- Determination of strength of welded corners and t-joints
TS EN 514 Non-plasticizing polyvinylchloride (pvc-U) profiles used in window and door manufacturing- Determination of strength of welded corners and t-joints
TS EN ISO 527-5Plastics - Determination of tensile properties - Part 5: Test conditions for one-way fiber-reinforced plastic composites
TS EN 542 Adhesives - Density determination
TS EN 543 Adhesives - Powder and granules - Determination of apparent density
TS EN ISO 604 Plastics - Determination of the change in properties vis-à-vis printing
TS 608 ISO 506 Natural rubber latex - Concentrate determination of the number of essential fatty acids
TS EN 682 Elastomeric seals - Material properties of pipe and fittings seals used in the transport of gas and hydrocarbon liquids
TS 703 EN ISO 584 (Formerly: TS 703 ISO 584) Plastics-Unsaturated polyester resins Determination of reactivity at 80 ° C (classical method)
TS 703 ISO 584: 1997 / T1 (Number modification, TS 703 EN ISO 584) Plastics-Unsaturated polyester resins Determination of reactivity at 80 ° C (classical method)
TS 785 EN ISO 489 Plastics - Determination of refractive index
TS ISO 813 Determination of adhesion to a rubber-vulcanized and thermoplastic-rigid support material
TS ISO 814 Rubber-Vulcanized-Determination of adhesion to metal-Double plate method
TS EN 827 Adhesives - Determination of conventional solid and fixed mass solids content
TS EN ISO 845 Porous plastics and rubbers - Determination of apparent (bulk) density
TS EN ISO 846 Plastics - Evaluation of the effect of microorganisms
TS 11191 EN 855 Plastic hoses and hose assemblies-Thermoplastic textile reinforced hydraulic type-Features
TS EN ISO 868 Determination of stiffness of plastics and ebonite by shear hardness
TS EN ISO 868 Determination of stiffness of plastics and ebonite by shear hardness
TS ISO 6194-3 Sealing elements - Rotary shaft lip type - Part 3: Storage, transport, loading, unloading and installation
TS ISO 6194-4 Sealing elements - Rotary shaft lip type - Part 4: Performance testing procedures
TS ISO 6194-5 Sealing elements - Rotary shaft lip type - Part 5: Identification of visible defects
TS EN ISO 899-2Plastics-Determination of creep property-Part 2: Flexural strength in three-point loading
TS EN ISO 899-1 Plastics-Determination of creep property-Part 1: Extrusion
TS EN 924 Adhesives - Adhesives with and without organic solvents - Determination of flash point
TS 1006-2 ISO 182-2: 1997 / T1 (Number modification, TS 1006-2 EN ISO 182-2) Plastics are based on vinylchloride homopolymers and copolymers of pulps and products at high temperatures. : Ph method
TS 1006-3 ISO 182-3: 1997 / T1 (Number modification, TS 1006-3 EN ISO 182-3) Determination of the tendency to release hydrogen chloride and other acidic products at high temperatures of plastics vinyl chloride homopolymers and copolymers based pastes and products - Part 3 : Conductometric method
TS 1006-4 ISO 182-4: 1997 / T1 (Number modification, TS 1006-4 EN ISO 182-4)
TS ISO 3996 Road vehicles - Hose assemblies for hydraulic braking systems with non-oil based brake fluids
TS 1065-1 ISO 11359-1 Plastics - Thermomechanical analysis (tma) - Part 1: General principles
TS 1065-2 ISO 11359-2 Plastics - Thermomechanical analysis (tma) - Part 2: Determination of linear thermal expansion coefficient and glass transition temperature
TS 1065-3 ISO 11359-3 Plastics - Thermomechanical analysis (tma) section 3: Determination of penetration temperature
TS 1066Plastics-Determination of flammability of self-supporting plastics
TS EN 1067 Adhesives - Preparation and inspection of samples for testing
TS EN 1114-3 + A1 Plastic and rubber machinery - Extruders and extrusion lines - Part 3: Safety requirements for towing equipment
TS 1116 EN ISO 1158 Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content
TS ISO 1125 Rubber dough additives - Determination of carbon black ash
TS ISO 1126 Rubber compound additives - Carbon black - Determination of heating loss
TS ISO 1147 Plastics / rubber-Polymer dispersions and synthetic rubber latexes-Freeze-Melt cycle stability test
TS 1149-1 EN ISO 294-1Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 1: General principles and molding of multi-purpose rod test pieces
TS 1149-2 EN ISO 294-2Plastics - Preparation of test pieces by injection molding of thermoplastic materials - Part 2: Small draw bars
TS ISO 974 Plastics - Determination of brittleness by impact
TS 1177 EN ISO 1172 Textile - Glass reinforced plastics - Prepregs, molding pulps and laminates - Textiles - Determination of glass and mineral filler content Calcination methods
TS 1178 EN ISO 1163-1 Plastics-poly (vinyl chloride) (pvc-U) molding and extrusion materials with no plasticizer-Part 1: System and principles for marking properties
TS EN ISO 1183-2 Plastics-Non-porous plastics-Density determination methods-Part 2: Gradient density column method
TS EN 1239: 2011 Adhesives - Freeze-thaw stability
TS EN 1240: 2011Adhesives - Determination of hydroxyl number and / or hydroxyl content
TS EN 1241 Adhesives - Determination of acid number
TS EN 1244 Adhesives-Color of adhesive layers and determination of color changes under the influence of light
TS EN ISO 1265 Plastics-Polyvinylchloride (pvc) resins-Determination of impurities and foreign particles
TS ISO 1268-1 Fiber-reinforced plastics-Methods of preparing test plates-Part 1: General requirements
TS ISO 1268-2 Fiber-reinforced plastics-Methods for the preparation of test plates-Part 2: Contact and injection molding
TS ISO 1268-3 Fiber-reinforced plastics-Methods for the preparation of test plates-Part 3: Wet pressure molding
TS ISO 1268-4 Fiber-reinforced plastics-Methods of preparing test plates-Section 4: Molding of preformed mixtures.
TS ISO 1268-5 Fiber-reinforced plastics-Methods for the preparation of test plates-Part 5: Filament winding
TS ISO 1268-6 Fiber-reinforced plastics-Methods of preparing test plates-Part 6: Extrusion molding by extrusion
TS ISO 1268-7 Fiber-reinforced plastics-Methods for the preparation of test plates-Part 7: Resin transfer molding
TS ISO 1268-8 Fiber-reinforced plastics-Methods of preparing test plates-Section 8: Compression molding of smc and bmc
TS ISO 1268-9 Fiber reinforced plastics - Methods for preparing test plates: Section 9: Gmt / stc molding.
TS ISO 1268-10 Glass-fiber reinforced plastics-Methods of preparing test plates-Part 10: Injection molding of BMC and other long-fiber molding compounds-General principles and molding of multi-purpose test pieces
TS ISO 1268-11 Fiber-reinforced plastics-Methods of preparing test plates-Part 11: Injection molding of Bmc and other long-fiber molding compounds-Small plates
TS EN ISO 1269 Plastics - Vinyl chloride homopolymer and copolymer resins - Determination of volatile matter (including water)
TS ISO 1304 Rubber pulp additives - Carbon black - Determination of the number of iodine adsorption
TS ISO 1306 Rubber compound additives - Carbon black (pelleted) - Determination of bulk density
TS EN 1347 tile adhesives - Determination of wettability
TS EN 1392 Adhesives - For leather and footwear materials - Solvent based and dispersion adhesives - Testing of adhesion strength under specified conditions
TS EN 1394 Plastic pipe systems - Glass fiber reinforced thermoset plastic (grp) pipes - Determination of initial visible ring tensile strength
TS ISO 1409 Plastics / rubber-polymer dispersions and rubber braids (natural and synthetic)
TS ISO 1409 Plastics / rubber-polymer dispersions and rubber braids (natural and synthetic)
TS ISO 1431-3 Tires and thermoplastics - Determination of resistance to ozone cracking part 3: Test methods for the determination of ozone concentration
TS ISO 1431-1 Tires and thermoplastics - Determination of resistance to ozone cracking part 1: Static and dynamic tensile test
TS ISO 1432 Rubber-Vulcanized or thermoplastic-Determination of tightness at low temperatures (gehman test)
TS ISO 1435 Rubber pulp additives - Carbon black (pelleted) - Determination of under-content
TS 1436 ISO 976Rubbers and plastics - Polymer dispersions and rubber latexes - Determination of Ph
TS ISO 1437 Rubber pulp additives - Carbon black - Determination of sieve residue
TS EN 1465 Adhesives - Determination of the release strength of overlap systems
TS EN 1566-1 Plastic pipe systems - Used for disposal of cold and hot water in buildings - Part of chlorinated polyvinylchloride (pvc-C) 1: Pipes, fittings and system properties
TS EN 1612-1 + A1 Rubber and plastic machinery - Reaction molding machines - Part 1: Safety requirements for measuring and mixing units
TS 1621 EN ISO 585 Plastics - Non-plasticizing cellulose acetate - Determination of moisture content
TS 1623 EN ISO 1061 (Formerly: TS 1623 ISO 1061) Plastics-Determination of free acidity of cellulose acetate without added plasticizer
TS 1623 ISO 1061: 1997 / T1 (Number modification, TS 1623 EN ISO 1061) Determination of free acidity of cellulose acetate without plasticizer
TS EN ISO 1624Plastics - Homopolymer and copolymer resins of vinyl chloride - Aqueous screen analysis
TS EN ISO 1628-2 Plastics - Determination of polymer viscosity - In dilute solutions - Capillary viscometer method - Part 2: Polyvinyl chloride resins
TS EN ISO 1628-1 Plastics - Determination of the viscosity of polymers in dilute solutions using capillary viscometers - Part 1: General rules
TS ISO 1628-5 Determination of viscosity in dilute solutions of polymers using capillary viscometers-Part 5: Thermoplastic polyester (tp) homopolymers and copolymers
TS EN ISO 1628-3 Plastics-Determination of viscosity and limit viscosity-Part 3: Polyethylenes and polypropylenes
TS 1677 EN ISO 308 Plastics - Phenolic molding materials - Determination of soluble substances in acetone (visible resin content of unmolded material)
tst 1678 EN ISO 604 Plastics - Determination of the change in properties vis-à-vis printing
TS EN 1719 Adhesives for paper and board, packaging and disposable sanitary materials - Measurement of adhesion in pressure sensitive adhesives - Determination of ring adhesion
TS 1724 ISO 1675: 1997 / T1 (Number modified, TS 1724 EN ISO 1675) Plastics liquid resins density determination-Pycnometer method
TS 1757 ISO 1795 Rubber-Raw-Natural and synthetic sampling and preparation
TS 1760 ISO 1656 Rubber-Raw natural rubber and natural rubber latex-Determination of the percentage of nitrogen
TS 1768 EN ISO 1264 Plastics-Homopolymer and copolymer resins of vinyl chloride-Determination of pH in aqueous extracts
TS EN 1778 Characteristic values for welded thermoplastic structures - Modules for thermoplastic equipment design and determination of permissible stresses
TS EN 1778 Characteristic values for welded thermoplastic structures - Modules for thermoplastic equipment design and determination of permissible stresses
TS EN ISO 1798 Polymeric materials - Flexible - Porous - Determination of tensile strength and elongation at break
TS EN 1799 Concrete structures - Products and systems for protection and repair - Test methods - Tests for measuring the applicability of adhesives used in the structure to the concrete surface
TS 1801 EN ISO 1060-1Plastics-Homopolymer and copolymer resins of vinyl chloride-Part 1: System and principles for marking properties
TS ISO 1802 Natural rubber latex concentrate - Determination of boric acid content
TS EN 1817 Elastic floor coverings - Homogeneous and heterogeneous flat surface rubber coverings - Specification
TS EN 1841 Adhesives - Test methods for adhesives used in floor coverings and wall coverings - Determination of the size change caused by adhesives in linol based floorings
TS 1852 ISO 1408 Tires-Determination of carbon black percentage-Pyrolytic and chemical decomposition methods
TS 1853 EN ISO 1597 Plastics -Plasticizing cellulose acetate - Determination of acetic acid yield
TS 1855 ISO 1922 Porous rigid plastics - Determination of shear strength
TS 1856 EN ISO 1923 Porous plastics and tires-Determination of linear dimensions
TS EN ISO 1856 / A1 Flexible, porous polymeric materials - Determination of crushing rate under pressure
TS 1877 EN ISO 1598 Plastics - Cellulose acetate - Determination of insoluble particles
TS EN 1895 Adhesives - for paper and cardboard, packaging and disposable sanitary products - 180º “t” separation test for joining flexible material to flexible material
TS EN 1895 / AC Adhesives - for paper and cardboard, packaging and disposable sanitary products - 180º “t” separation test for joining flexible material to flexible material
TS EN 1896 Adhesives - for paper and cardboard, packaging and disposable health products - Determination of tensile strength and elongation.
TS EN 1939 Adhesive tapes - Determination of peel resistance
TS EN 1965-1: 2011 Structural adhesives - Corrosion - Part 1: Determination and classification of corrosion in copper base material
TS EN 1966 Structural adhesives - Characterization of surfaces - Measurement of adhesion by three-point bending
TS ISO 2000 Rubber, raw natural-technical guide for specification
TS ISO 2004 Natural rubber latex concentrate-Centrifuged or creamed, ammonia-protected types
TS ISO 2005 Natural rubber latex concentrate - Determination of sediment content
S 2009-1 ISO 289-1 Rubbers - Non-vulcanized - Determination with viscometer with shear disk Part 1: Determination of Mooney viscosity
TS 2009-2 ISO 289-2 Rubbers-Unvulcanized-Determination by viscometer with shear disk section 2: Determination of pre-vulcanization properties
TS ISO 2028 Synthetic rubber latex-Dry polymer preparation
TS EN ISO 2039-1 Plastics-Determination of hardness section 1: Ball dipping method
TS EN ISO 2440 / A1 Flexible and hard porous polymeric materials - Accelerated aging tests
TS EN ISO 2114 / AC Plastics (polyester resins) - Paints and varnishes (binders) - Determination of partial acid value and total acid value
TS ISO 2115 Plastics-Polymer dispersions-Determination of white dot temperature and lowest film formation temperature
TS 2159Plasticizing esters (phthalate and sebacate esters)
TS 2252 EN ISO 3001 Plastics-Epoxy compounds-Determination of epoxy equivalents
TS ISO 2303 Tires-Isoprene tire-Evaluation of vulcanization properties obtained by oil-free solution polymerization
TS ISO 2322 Styrene-Butadiene rubber (sbr) - Emulsion and solution polymerized types-Evaluation procedures
TS 2351 EN 1842 Plastics-Thermosetting molding pulp (smc-Bmc) determination of compression molding shrinkage
TS 2403 EN ISO 2554 Plastics - Unsaturated polyester resins - Determination of hydroxyl value
TS 2437 ISO 1110: 1997 / T1 (Number modification, TS 2437 EN ISO 1110) Accelerated conditioning of plastics-polyamides test pieces
TS EN ISO 2439 Flexible, porous polymeric materials - Determination of hardness (penetration method)
TS ISO 2454 Rubber products - Determination of zinc content - Titrimetric method with Edta
TS ISO 2475 Chloroprene rubber (cr) - General purpose types - Evaluation process
TS ISO 2561 Plastics-Determination of styrene monomer residue in polystyrene by gas chromatography
TS EN ISO 2578 Plastics - Time after long exposure to heat - Determination of temperature limits
TS 2610 ISO 2453 Raw rubber-Styrene butadiene-Emulsion polymerized-Determination of bound styrene content -Refractive index method
TS ISO 2796 Porous rigid plastics - Dimensional stability test
TS 2826 EN ISO 2440 Flexible and hard porous polymeric materials - Accelerated aging tests
TS 2845 ISO 2008 Determination of rubber latex, styrene-Butadiene-Unsaturated volatile components
TS 2859 ISO 1827 Rubber, vulcanized or thermoplastic-Determination of the bonding strength of cutting module or rigid plates-Quadrupole cutting method
TS EN ISO 2897-2 Plastics-Impact-resistant polystyrene (ps-I) molding and extrusion materials-Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 2898-2 Plastics -Plasticizing poly (vinyl chloride) (pvc-P) molding and extrusion materials-Part 2: Preparation of test specimens and determination of properties
TS ISO 2930 Natural raw rubber - Determination of plasticity index (PRI)
TS 2992 ISO 800Plastics - Phenolic molding materials - Specifications
TS 3047 ISO 812Types-Determination of low temperature brittleness
TS EN ISO 3146 + AC Plastics - Determination of melting property (melting temperature or melting range) of semi-crystalline polymers
tst 3154 EN ISO 3671 Determination of volatile matter in plastics-aminoplastic molding materials
TS 3155 EN ISO 4608 Plastics - Vinyl chloride homopolymer and copolymer resins - General purpose - Determination of plasticizer absorption at room temperature
TS 3198 EN ISO 3521 Plastics - Unsaturated polyester and epoxy resins - Determination of total volume shrinkage
TS 3199 EN ISO 4614 Plastic - Molded products from melamine-formaldehyde - Determination of extractable formaldehyde
TS ISO 3257 Tire additives - Carbon black - Method for the evaluation of styrene-butadiene tires
TS EN ISO 3386-2 / A1 Determination of tensile and elongation properties of flexible and porous polymeric materials in section 2: High-density materials
TS ISO 3387 Determination of degree of crystallization by rubber-hardness measurements
TS 3422 ISO 2476 Rubber-Butadiene (br) - Solution polymerized types evaluation processes
TS 3436 ISO 3417 Measurement of rubber-vulcanization properties by oscillating disc curmeter
TS EN ISO 3451-5 Plastics-Determination of ash part 5: Polyvinylchloride
TS EN ISO 3451-1 Plastics - Determination of ash - Part 1: General methods
TS 3484 ISO 1658 Natural rubber - Evaluation process
TS 3564 ISO 2007 Rubber, non-vulcanized-Determination of plasticization property-Rapid plastimetry method
TS EN ISO 3582 / A1 Flexible porous polymeric materials - Laboratory evaluation of horizontal combustion properties of small test specimens exposed to a small flame
TS ISO 3597-3 Woven-Glass fiber-Reinforced plastics-Determination of mechanical properties of wick-reinforced resin rods-Part 3: Determination of compression strength
TS EN ISO 3671 Determination of volatile matter in plastics-Aminoplastic molding materials
TS ISO 3739-2 Industrial tires and wheels-Part 2: Pneumatic tires (metric series) on 5 highly tapered or flat-bottomed rims - Load capacities
TS ISO 3858 Rubber pulp additives - Carbon black - Determination of light transmittance of toluene extract
TS 3872 ISO 3865 Determination methods of staining in contact with rubber-organic materials
TS ISO 3877-1 Tires, valves and inner tubes - List of terms section 1: Tires
TS ISO 3877-2 List of equivalent terms for tires, valves and inner tubes - Part 2: Valves
TS ISO 3899 Rubber-Nitrile latex-Determination of residual acrylonitrile content
TS ISO 3900 Determination of rubber-nitrile latex-bound acrylonitrile content
TS EN ISO 4080 Rubber and plastic hoses and hose assemblies - Determination of gas permeability
TS EN ISO 4167 Polyolefin agricultural cords
TS ISO 4223-2 Description of some terms used in the tire industry - Part 2: Solid tires
TS ISO 4249-2 Motorcycle tires and rims (code marked series) section 2: Classification according to the loads the tires can bear
TS EN 4384 High-pressure ornamental sheets (hpl) - Thermosetting resin-based sheets (commonly referred to as sheets) - Part 4: Classification and properties of sheets of thickness 2 mm or more
Plastics-Vinyl chloride (pvc-P) homopolymer and copolymer compounds -Plasticized-Section 4410: Indication by markings TS 2898 EN ISO 1-4410 (Former number: TS 2898 ISO 1-1)
TS 4410 ISO 2898-1: 1997 / T1 (Number modification, TS 4410 EN ISO 2898-1) Plastics - Vinyl chloride (pvc-P) homopolymer and copolymer compounds - Plasticized - Part 1: Indication by signs
TS 4526 ISO 4660 Rubber, natural raw color index test
TS ISO 4575 Plastics-Poly (vinylchloride pastes-Determination of visible viscometer using Severs rheometer
TS ISO 4576 Plastics-Polymer dispersions-Determination of sieve residue (coarse particles and coagulated content)
TS EN ISO 4577 Plastics - Polypropylene and propylene copolymers - Determination of resistance to oxidation in hot air - Oven method
TS ISO 4581 Plastics-Styrene / acrylonitrile copolymers-Determination of residual acrylonitrile monomer content-Gas chromatography method
TS 4589 EN ISO 3386-2 Determination of tensile and elongation properties of flexible and porous polymeric materials in compression section 2: High-density materials
TS EN ISO 4589-2 / A1 Plastics - Determination of combustion properties by oxygen index - Part 2: Determination of ambient temperature
TS 4595 ISO 815Lastics and thermoplastics - Determination of permanent crush rate under pressure at ambient, high or low temperatures
TS EN ISO 4597-1 Plastics-Hardeners and accelerators for epoxy resins-Part 1: Marking
TS ISO 4613-1: 1996 / T1 (Number amendment, TS EN ISO 4613-1) Plastics-Ethylene / vinyl acetate (e / vac) molding and extrusion materials-Part 1: Indication and identification with markings
Plastics-Ethylene / vinylacetate (e / vac) molding and extruding agents TS EN ISO 4613-2 / A1 section 2: Preparation of test specimens and determination of their properties
TS EN ISO 4651 / A1 Tire and plastics-Porous-Determination of dynamic buffering performance - Amendment
TS ISO 4656-1 Rubber pulp additives - Carbon black - Determination of the absorption number of dibutyl phthalate - Part 1: Absorptometric method
TS ISO 4658 Acrylonitrile-Butadiene-Rubber (nbr) - Evaluation process
TS ISO 4659 Styrene-Butadiene rubber (carbon black or oil added) - Evaluation process
TS ISO 4664-1 Tire - Vulcanized or thermoplastic - Determination of dynamic properties - Part 1: General guide
TS ISO 4665 Rubber - Vulcanized or thermoplastic - Resistance to climatic conditions
TS 4699 ISO 2878 Tires-Antistatic and conductive products-Determination of electrical resistances
TS ISO 4899 Textile-Glass reinforced thermoset plastics-Properties and test methods
TS ISO 4928 Road vehicles - Brake systems - Brake cylinder (hydraulic) seals and pump rubber (elastomer) - For non-petroleum hydraulic brake fluid (operating temperature up to 120 ° c)
TS 4999 ISO 4097 Rubber-Ethylene, propylene, diene (epdm) -General purpose types-Evaluation procedures
5264-2: 2011 Paper pulps - Laboratory grinding - Section 2: Pfi grinding method
TS 5323 ISO 3384 Tires and thermoplastics-Determination of the rate of reduction of the counter-force occurring under pressure at ambient and elevated temperatures over time
TS ISO 5435 Rubber compound additives - Carbon black - Determination of tint strength
TS 5515 ISO 2302 Rubber-Isobutene, isoprene
TS ISO 5751-1 Motorcycle tires and wheels-Part 1: Design guides
TS ISO 5751-2 Motorcycle tires and wheels (metric series) - Tire dimensions and load carrying capacities
TS ISO 5775-1 Bicycle tires and wheels - Part 1: Tire dimensions and marking
TS ISO 5794-1 Rubber dough additives-Silica, precipitated, hydrated-Part 1: Non-tire tests
TS ISO 5796 Rubber pulp additives-Natural calcium carbonate-Test methods
Plastics - Liquid, emulsion or dispersion polymers - Resins - Determination of viscosity using a rotary viscometer at a given shear rate
TS ISO 5945 Tire - Determination of polyisoprene content
TS 6013 EN ISO 6945 Rubber hoses - Determination of abrasion resistance of the outer casing
TS ISO 6101-2 Determination of metal content by rubber-atomic absorption spectrometer-Part 2: Determination of lead content
TS 6126 EN ISO 2555 (Formerly: TS 6126 ISO 2555) Plastics-Resins in liquid or emulsion or dispersed form-Determination of apparent viscosity brookfield method
TS 6126 ISO 2555: 1998 / T1 (Number modification, TS 6126 EN ISO 2555) Plastics-Resins in liquid or emulsion or dispersed form-Determination of apparent viscosity brookfield method
TS ISO 6133 Rubber and plastics-Analysis of multiple peaks obtained in the determination of tear strength and adhesion strength
TS ISO 6133 Rubber and plastics-Analysis of multiple peaks obtained in the determination of tear strength and adhesion strength
TS EN ISO 6179 Rubber, vulcanized or thermoplastic - Rubber sheets and rubber coated fabrics - Determination of the velocity of volatile liquids (gravimetric technique)
TS ISO 6209 Tire additives - Carbon black - Determination of extractables
TS ISO 6225-2 Natural raw rubber - Determination of castor oil content - Part 2: Determination of total ricinoleic acid content - Gas chromatography method
TS ISO 6238 Adhesives-Wood-Wood bonding bonds-Determination of shear strength by pressure loading
TS 6295 EN ISO 3681 Binders for paints and varnishes - Determination of saponification number - Titrimetric method
TS EN ISO 6383-1 (Formerly: TS ISO 6383-1) Plastics- Film and sheets- Determination of tear strength- Part 1: Pantalon type tear method
TS EN ISO 6383-2 (Formerly: TS ISO 6383-2) Plastics- Film and sheets- Determination of tear strength- Part 2: Elmendorf method
TS ISO 6383-2: 2001 / T1 (Number amendment, TS EN ISO 6383-2) Plastics- Film and sheets- Determination of tear strength- Part 2: Elmendorf method
TS 6391 EN ISO 1060-2Plastics-Homopolymer and copolymer resins of vinyl chloride-Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 6401Plastics-Vinyl chloride homopolymer and copolymer resins-Determination of vinyl chloride monomer residue-Gas chromatographic method
TS EN ISO 6402-1 Plastics - Impact-resistant, acrylonitrile / styrene (asa, aes, acs) based molding and extrusion materials (except those modified with butadiene) section 1: Indication of properties and property criteria
TS EN ISO 6402-2 Plastics - Impact resistant, acrylonitrile / styrene (asa, acs) type molding and extrusion materials - except for butadiene modified materials - Part 2: Preparation of test pieces and determination of their properties
TS ISO 6471 Rubber, vulcanized-Determination of degree of crystallization under load
TS ISO 6505 Determination of adhesion and corrosion tendency to rubber-vulcanized or thermoplastic-metals
TS EN ISO 6603-1 Plastics- Determination of the impact strength of rigid plastics - Part 1: Tool-less impact test
TS EN ISO 6603-2 Plastics- Determination of the impact strength of rigid plastics- Part 2: Instrument impact test
TS 6682 ISO 4652-1 Tires-Rubber pulp additives-Determination of carbon black specific surface area by nitrogen adsorption method-Part 1: Single point methods
TS 6684 ISO 4656-2 Tires-Rubber pulp additives-Carbon black-Determination of dibutyl phthalate absorption number-Part 2: Method using plastograph or plastic border
TS 6689 EN ISO 1599 Plastics-Cellulose acetate-Determination of viscosity loss during molding
TS 6698 EN ISO 6186 Plastics - Determination of flowability
TS EN ISO 6721-3 Plastics- Determination of dynamic mechanical properties part 3: Bending vibration resonance curve method
TS ISO 6721-5 Plastics- Determination of dynamic mechanical properties- Part 5: Bending vibration- Resonance-free method
TS ISO 6721-6 Plastics - Determination of dynamic mechanical properties - Part 6: Shear vibration - Resonance free method
TS ISO 6721-7 Plastics- Determination of dynamic mechanical properties- Part 7: Torsional vibration- Resonance-free method
TS ISO 6721-8 Plastics- Determination of dynamic mechanical properties- Part 8: Longitudinal vibration and shear vibration- Wave propagation method
TS ISO 6721-9 Plastics - Determination of dynamic mechanical properties - Part 9: Stress vibration - Propagation of sound waves
TS ISO 6721-10 Plastics - Determination of dynamic mechanical properties - Part 10: Complex shear viscosity - Rheometer method with parallel plate oscillator
TS EN ISO 6721-2 Plastics- Determination of dynamic mechanical properties - Part 2: Torsion pendulum method
TS EN ISO 6721-1: 2011 Plastics- Determination of dynamic mechanical properties-Part 1: General principles
Plastics - Epoxy resins - Part 6723: Display with markings TS 3673 EN ISO 1-1 Plastics
TS 6754 EN ISO 7662 Rubber and plastic hoses - Determination of liner wear
TS ISO 6805 Rubber hoses and hose elements for underground mining - Wire reinforced hydraulic types for coal mining
TS ISO 5893 Test equipment for rubber and plastics - Tensile, stretching and compression type devices (constant speed) - Description of the devices
TS ISO 6915 Flexible porous polymeric materials - Polyurethane foam, used for making laminated sheets - Specifications
TS ISO 6916-1Flexible, porous polymeric materials - Sponge and expanded porous rubber products - Specification - Part 1: Sheets
TS 6995 EN ISO 3672-1 Plastics-Unsaturated polyester resins (up-R) section 1: System for indication of properties
TS 6999 EN ISO 3582 Flexible porous polymeric materials-Laboratory evaluation of horizontal combustion properties of small test specimens exposed to a small flame
TS 7237 ISO 4592 Plastics-Films and sheets-Determination of length and width
TS ISO 7269 Tires - Determination of free sulfur
TS EN ISO 7327Plastics - Hardeners and accelerators for epoxy resins - Determination of acid anhydride and free acid
TS EN ISO 7327 Plastics - Hardeners and accelerators for epoxy resins - Determination of acid anhydride and free acid
TS 7494 ISO 5478 Determination of rubber-styrene content-Nitrolation method
TS ISO 7619-2 Tire - Vulcanized or thermoplastic - Determination of notch hardness - Part 2: Method of measurement with pocket type armor
TS 7639 ISO 3451-2 Plastics-Determination of ash-Part 2: Polyalkylene terephthalates
TS 7639 ISO 3451-2 Plastics-Determination of ash-Part 2: Polyalkylene terephthalates
TS 7663 ISO 4591 Plastics-Films and sheets-Determination of the average thickness of a sample and the average thickness and yield of a roll by gravimetric techniques (gravimetric thickness)
TS 7736 EN ISO 3451-4 Plastics - Determination of ash - Part 4: Polyamides
TS ISO 7765-1: 2003 / T1 (Number modification, TS EN ISO 7765-1) Plastic films and sheets - Determination of impact strength by free falling mass method - Part 1: Ladder method
TS EN ISO 7808Plastics - Thermoset molding materials - Determination of flow mass transfer
TS EN ISO 7822Textile - Determination of void content of glass-reinforced plastics-Glow loss, mechanical separation and statistical counting methods
TS EN ISO 7823-1 Plastics - Poly (methyl methacrylate) sheets - Types, dimensions and specifications - Part 1: Cast sheets
TS EN ISO 7823-3 Plastics - Thermoplastic polyester (tp) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 7823-2 Plastics - Poly (methyl methacrylate) sheets - types, dimensions and specifications - Part 2: Extruded sheets
TS ISO 7850 Porous plastics, rigid - Determination of compression compression
TS 7901 EN ISO 1622-2 Plastics - Polystyrene (ps) molding and extrusion materials - Part 2: Preparation of test pieces and determination of their properties
TS 7911 EN ISO 4615 Plastics - Unsaturated polyester and epoxy resins - Determination of total chloride content
TS 8014 ISO 6101-1 Rubber-Metal determination-Atomic absorption spectrometric method part 1: Determination of zinc
TS ISO 8066-2 Rubber and plastic hose and hose assemblies - Used in automotive air conditioners - Specifications - Part 2: Refrigerant for 134a
TS EN ISO 8067 Flexible porous polymeric materials - Determination of tear strength
TS 8105 ISO 1628-4 Plastics-Determination of the viscosity of dilute polymer solutions using capillary viscometers-Part 4: Polycarbonate (pc) molding and extrusion materials
TS 8106-4 ISO 4892-4 Plastics-Methods of exposure to laboratory light sources-Section 4: Open-flame carbon arc lamps
Plastics - Poly (methyl methacrylate) (pmma) molding and extrusion materials - Part 8257: System and principles of marking features
Plastics - Poly (methyl methacrylate) (pmma) molding and extrusion materials - Part 8257: System and principles of marking features
TS ISO 8257-2 / T1 (Number modification: TS EN ISO 8257-2) Plastics - Poly (methyl methacrylate) (pmma) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 8295 Plastics - Films and sheets - Determination of coefficient of friction
TS ISO 8296 Plastics-Films and sheets-Determination of wetting resistance
TS ISO 8301 Thermal insulation - Determination of thermal resistance and related properties in steady state - Methods for determination of heat flow
TS EN ISO 8307 Polymer materials - Porous and flexible - Determination of recoil properties
TS 8447 ISO 4650 Rubber-Infared spectrometric method
TS EN ISO 8510-2 Adhesives-Peel test of two test specimens, one of which is flexible and the other is rigid - Part 2: Stripping test at 180 ° angle
TS ISO 8511 Rubber pulp additives - Carbon black - Determination of pellet size distribution
TS 8568 EN ISO 4651 Tire and plastics-Porous-Determination of dynamic buffering performance
TS ISO 8570 Plastics - Film and sheets - Determination of the refraction temperature in cold
TS ISO 8604 Plastics-Pre-impregnated mixtures-Definitions of terms and symbols used in marking
TS ISO 8605 Textile-Glass reinforced plastics - Sheet molding pulps (lkh) - Basis for specifications
TS EN ISO 8619 Plastics - Phenolic resin powder - Determination of yield distance on glass plate
TS 8759 ISO 14898 Plastics - Aromatic isocyanates used in the production of polyurethane - Determination of acidity
TS ISO 8916 Ethylene - Used in industry - Determination of trace amounts of polar compounds - Preparation of samples enriched with low temperature washing technique
TS 8942 ISO 6528-2 Rubber-Determination of total sulfur content part 2: Sodium peroxide melting method
TS 8969 ISO 6502 Determination of vulcanization properties of rubbers with non-rotating curmeter
TS EN ISO 8975Plastics-Phenolic resins-Ph determination
TS EN ISO 8985Plastics - Ethylene / vinyl acetate copolymer (evac) - Thermoplastics - Determination of vinyl acetate content
tst EN ISO 8986-2 Plastics - Polybutene (pb) molding and extrusion materials - Part 2: Preparation of test pieces and determination of their properties
TS EN ISO 8986-2 Plastics - Polybutene (pb) molding and extrusion materials - Part 2: Preparation of test pieces and determination of their properties
TS EN ISO 8987Plastics-Phenolic resins-Determination of reactivity on a b-Alternating test plate
TS EN ISO 8988 Plastics - Phenolic resins - Determination of hexamethylenetetramine - Kjeldahl method and perchloric acid method
TS EN ISO 8989 Plastics-Liquid phenolic resins-Determination of water miscibility
TS ISO 9011 Road vehicles - Motor vehicles - Non-slip (synchronized) pulleys
TS EN ISO 9054 Porous plastics, rigid - Test methods for self-shelling high density materials
tst EN ISO 9080 Thermoplastic pipes - Used for the transport of fluids - Determination of the long term hydrostatic strength of thermoplastic pipe materials - Methods based on extrapolation of rupture data due to hydrostatic stress
TS 9140 EN ISO 3915 Plastics - Determination of resistivity of conductive plastics
TS EN ISO 9142 Adhesives - Guide to the selection of standard laboratory aging conditions for testing joints
TS 9220 EN 26801 Rubber and plastic hoses - Determination of volumetric expansion
TS ISO 9252 Synthetic rubber latex-Microbiological inspection
TS EN ISO 9311-1 Adhesives for thermoplastic pipe systems - Part 1: Determination of film properties
TS EN ISO 9311-3 Adhesives for thermoplastic pipe systems - Part 3: Test method for the determination of internal pressure resistance
TS EN ISO 9396 Plastics - Phenolic resins - Determination of the gelation time of resols using automatic devices
TS 9406 EN ISO 2039-2 Plastics - Determination of hardness - Part 2: Rockwell hardness
TS ISO 9553 Preformed rubber based sealing elements used in solar collectors- Test methods
S EN ISO 9653 Adhesives - Determination of resistance to shear impact at bonding sites
TS EN ISO 9665 Adhesives - Animal glues - Sampling and test methods
TS EN ISO 9702 Plastics - Amine epoxide hardeners - Determination of primary, secondary and tertiary amine group nitrogen content
TS EN ISO 9771 plastics-Phenolic resins- Determination of pseudo adiabatic temperature rise of liquid resols cured under acidic conditions
TS EN ISO 9773 Plastics - Determination of combustion properties of vertical, thin, flexible test specimens in contact with a small flame ignition source
TS EN ISO 9773 / A1 Plastics - Determination of the combustion properties of thin, flexible test specimens in vertical position in contact with a small flame ignition source
TS ISO 9924-1 Rubber and rubber products - Determination of the composition of vulcanizates and uncured doughs by thermogravimetry - Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers
TS EN ISO 9944 Plastics-Phenolic resins-Determination of electrical self-conductivity of resin extracts
TS EN ISO 10066 Polymer materials - Porous and flexible - Determination of creep property under pressure
TS EN ISO 10082 Plastics-Phenolic resins-Definitions and test methods
TS EN ISO 10139-1 Adhesives for thermoplastic pipe systems - Part 3: Test method for determination of internal pressure resistance
TS EN ISO 10350-2: 2011 Plastics - Acquisition and reporting of comparable single point data - Part 2: Long fiber reinforced plastics
TS EN ISO 10363 hot melt adhesives - Determination of thermal stability
tst 10363 EN ISO 8295 Plastics - Film and sheets - Determination of coefficient of friction
TS EN ISO 10365 Adhesives - Demonstration of major defects
TS EN ISO 10366-2 Plastics - Methyl methacrylate / acrylonitrile / butadiene / styrene (mabs) type molding and extrusion materials part 2: Preparation of test pieces and determination of properties
tst 10484 EN ISO 5999 (Priority 5) Polymeric materials - Porous, flexible - Polyurethane foam - For load-bearing applications (excluding under carpet coating)
TS ISO 10500 Industrial vehicle tires and wheels-Cylindrical and conical rubber-filled tires (metric series) -Short designations, dimensions and marking
TS EN ISO 10601 Plastics - Homopolymer and copolymer resins of vinyl chloride Chapter 1: Short demonstration system and principle of properties
TS EN ISO 10724-2 Plastics - Preparation of test pieces by injection molding from thermoset powder molding mixtures - Part 2: Small plates
TS 11162-1 EN ISO 4589-1 Plastics - Determination of combustion behavior with oxygen index - Part 1: Guide
TS 11162-2 EN ISO 4589-2 Plastics - Determination of combustion properties by oxygen index - Part 2: Determination of ambient temperature
TS 11162-3 EN ISO 4589-3 Plastics - Determination of combustion properties by oxygen index - Part 3: High temperature test
S ISO 11236 Rubber pulp additives-P-Phenylenediamine (ppd) degradation inhibitors-Test methods
TS EN ISO 11248 Plastics - Thermosetting molding materials - Short term performance evaluations at high temperatures
TS EN ISO 11358 Plastics - Thermogravimetric analysis of polymers (tg) - General principles
TS EN ISO 11402Fenolic, amino and condensation resins - Determination of free formaldehyde
TS EN ISO 11402 / AC Phenolic, amino and condensation resins - Determination of free formaldehyde content
TS 11415 EN ISO 4894-2 Plastics-Styrene / acrylonitrile (yellow) molding and extrusion materials-Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 11468 Plastics - Preparation of PVC dough for test purposes - Thawing method
TS EN ISO 11502 Plastics-Films and sheets-Determination of blocking resistance
TS EN ISO 11542-2 Plastics - Molding and extrusion materials - Very high molar polyethylene (pe-Uhmw) - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 11542-2 / AC Plastics - Molding and extrusion materials - Very high molar mass polyethylene (pe-Uhmw) - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 11667 Plastic fibers - Reinforced - Molding pulps and prepregs - Determination of resin, reinforced fibers and mineral fillers - Dissolving method
TS EN ISO 11833-2 (Formerly: TS ISO 11833-2) Plastics - Polyvinylchloride sheets without plasticizers - Types, dimensions and specifications - Part 2: Plates of thickness less than 1mm
TS ISO 11833-2 / T1 (Number modification: TS EN ISO 11833-2) Plastics - Non-plasticized polyvinylchloride sheets - Types, dimensions and specifications - Part 2: Plates with thickness less than 1mm
TS EN 12012-2 + A2 Tire and plastic machines - Size crushers - Part 2: Safety requirements for granulators
TS EN 12012-4 + A1 Plastic and rubber machinery - Size reduction machines - Part 4: Safety rules for agglomerators
TS EN 12012-1 + A1 Tire and plastic machines - Size crushers - Part 1: Safety rules for knife granulators
TS EN 12013 + A1 Plastic and rubber machines - Internal mixers - Safety regulations
TS EN 12012-3 + A1 Plastic and rubber machines - Shrinking machines - Part 3: Safety rules for choppers
TS EN 12025 Adhesive tapes-Measurement of tear strength by pendulum method
TS EN 12028 Adhesive tapes-Measurement of elongation and elongation under static load
TS EN 12032 Adhesive tapes-Measurement of adhesion of thermoset adhesive tapes during curing
TS EN 12033 Adhesive tapes-Measurement of adhesion of thermoset adhesive tapes after curing
TS EN 12034 Adhesive tapes-Measuring the lengths of roll adhesive tapes
TS EN 12036 Adhesive tapes-Solvent penetration into adhesive masking tapes
TS EN ISO 12058-1 / AC Plastics - Determination of viscosity using ball-drop viscometer - Part 1: Slope pipe method
TS EN ISO 12086-1 Plastics - Molding and extrusion materials with fluoropolymer dispersions - Part 1: System and principles of marking features
TS EN ISO 12086-2 Plastics - Fluoropolymer dispersions and molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 12086-2 / AC Plastics - Fluoropolymer dispersions and molding and extrusion materials - Part 2: Preparation of test specimens and determination of their properties
TS EN 12092 Adhesives - Determination of viscosity
TS EN 12099 Plastic pipe systems-Polyethylene pipe materials and elements-Determination of volatile content
TS EN 12106 Plastic pipe systems - Polyethylene (pe) pipes - Strength test to internal pressure after compression
TS EN ISO 12114Fiber reinforced plastics - Thermosetting molding doughs and mixtures - Determination of curing properties
TS EN 12118 Plastic pipe systems - Determination of moisture content in thermoplastics by coulometry method
TS EN 12118 Plastic pipe systems - Determination of moisture content in thermoplastics by coulometry method
TS EN 12192-2 Concrete structures - Products and systems for protection and repair - Determination of particle size distribution - Part 2: Test method for fillers of polymeric adhesives
TS 12225 Workplaces - Door or window systems made of rigid pvc - General rules
TS EN 12301 + A1 Plastic and rubber machinery - Calenders - Safety rules
TS EN 12576 Plastics - Fiber reinforced composites - Preparation of test plates for smc, bmc and dmc by pressure molding
TS EN 12576 Plastics - Fiber reinforced composites - Preparation of test plates for smc, bmc and dmc by pressure molding
TS EN 12615 Concrete structures - Products and systems for protection and repair - Test methods - Determination of shear strength in joining tendency
TS EN 12701 Structural adhesives-Storage-Terms and explanations related to shelf-life and storage conditions of structural adhesives and related materials
TS EN 12702 Adhesives - For paper and cardboard, packaging and disposable sanitary products - Determination of blocking properties of possible adhesive layers
TS EN 12705: 2011 Adhesives for leather and footwear materials - Determination of discoloration of white and bright colored leather surfaces
TS EN 12808-1 Joint fillers - For tiles - Part 1: Determination of the chemical resistance of reaction resin mortars
TS EN 12808-5 Joint fillers - For tiles - Part 5: Determination of water absorption
TS EN 12808-3 Joint fillers - For tiles - Part 3: Determination of flexural and compressive strength
TS EN 12860 Adhesives - Gypsum based - For gypsum blocks - Definitions, specifications and test methods
TS EN 12877-1 Coloring agents - Used in plastics - Determination of color stability of colorants during heat treatment - Part 1: General information
TS EN 12877-2 Coloring agents - Used in plastics - Determination of color stability of colorants against heat during processing of plastics - Part 2: Determination by injection molding
TS EN 12877-3 Coloring agents - Used in plastics - Determination of color stability of colorants against heat during processing of plastics - Part 3: Test for determination by oven
TS EN 12877-4 Coloring agents - Used in plastics - Determination of color stability of colorants against heat during processing of plastics - Part 4: Determination by double roll grinder
TS EN ISO 12944-6 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 6: Laboratory performance test methods
TS EN 12960 / AC Adhesives - for paper and cardboard, packaging and disposable sanitary products - Determination of slip resistance
TS EN 12961 / A1 Adhesives - For leather and footwear materials - Determination of the maximum operating life and optimum operating temperatures of solvent-based and dispers-type adhesives
TS EN 12962: 2011 Adhesives - Determination of elasticity of liquid adhesives (index of elasticity)
TS ISO 12965 Butadiene rubber - Microstructure determination by infrared spectrometric method
TS ISO 12992 Plastics-Determination of vertical flame spread in films and sheets
TS EN ISO 13000-1 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: System and principles of marking features
TS EN 13245-3: 2010 Plastics - Polyvinylchloride (pvc-U) profiles with no plasticizer added - For building applications - Part 2: Indication of PVC-Ue profiles with signs
TS EN 13415 Adhesives for floor coverings - Determination of electrical resistance in adhesive films and composites
TS EN 13421 Plastics - Thermosetting molding mixtures - Composites and reinforcing fibers - Preparation of samples for the determination of anisotropic properties of compressed molding mixtures
TS EN ISO 13445Adhesives - Determination of shear strength of adhesive bonds between rigid base materials by block shift method
TS EN 13655 Plastics - Thermoplastic films used as cover in horticultural and field agriculture
TS EN 13677-1 Reinforced thermoplastic molding pulps - Specification for Gmt - Part 1: Indication
TS EN 13677-3 Reinforced thermoplastic molding pulps - Specifications for Gmt - Part 2: Specific features
TS EN 13706-2 Reinforced plastic composites - Properties of extruded profiles - Part 2: Test methods and general properties
TS EN 13706-2 Reinforced plastic composites - Properties of extruded profiles - Part 2: Test methods and general properties
TS EN 13706-3 Reinforced plastic composites - Properties of extruded profiles - Part 3: Specific features
TS EN 13706-3 Reinforced plastic composites - Properties of extruded profiles - Part 3: Specific features
TS EN 13887 Structural adhesives - guide to surface preparation of metals and plastics before bonding
TS EN 13900-1 Pigments and additives - Dispersion methods and evaluation of dispersibility in plastics - Part 1: General information
TS EN 13900-2 Pigments and additives - Dispersion methods and evaluation of dispersibility in plastics - Part 2: Determination of ease of dispersion and color properties in plasticized polyvinylchloride by double roll mill
TS EN 13900-3 Pigments and additives - Dispersion methods and evaluation of dispersibility in plastics - Part 3: Determination of ease of dispersion and color properties of black and colored pigmnets in polyethylene with a double roller mill
TS EN 13900-4 Pigments and additives - Dispersion methods and evaluation of dispersibility in plastics - Part 4: Determination of ease of dispersion and color properties of white pigments by using a double roller mill in polyethylene
TS EN 13900-5 Pigments and additives - Dispersion methods and evaluation of dispersibility in plastics - Part 5: Determination by filtration test
TS EN 13925-3 Non-destructive testing - X-ray diffraction in polycrystalline and amorphous materials - Part 3: Instruments
TS EN 13999-3 + A1 Adhesives - Short-term method for measuring emission characteristics of adhesives without organic solvent or low content - Part 3: Determination of volatile aldehydes
TS EN 13999-4 + A1 Adhesives - Short-term method for measuring emission characteristics of adhesives without organic solvent or low content after application - Part 4: Determination of volatile diisocyanates
TS EN 14022 Adhesives - For carrier applications - Determination of the shelf life of multi-part adhesives
TS EN ISO 14125 / AC Fiber reinforced plastic composites - Determination of bending properties
TS EN ISO 14125 Fiber reinforced plastic composites - Determination of flexural properties
TS EN ISO 14130Plastic composites - Fiber reinforced - Shear strength between layers - Short beam method
TS EN 14257 Adhesives - Wood adhesives - Determination of tensile strength of overlap joints at high temperature
TS EN 14258 Structural adhesives - Mechanical behavior of glued joints subjected to short-term or long-term exposure under specified temperature conditions
TS EN 14259 Adhesives for floor coverings - Mechanical and electrical performance properties
TS EN 14292 Adhesives - Wood adhesives - Determination of static load resistance with increasing temperature
TS EN 14293 Adhesives - Adhesives for bonding parquet to subfloor - Test methods and minimum requirements
TS EN 14444 Structural adhesives - Qualitative evaluation of strength of bonded systems - Wedge break test
TS EN 14447 Fiber reinforced plastics - Glass felt reinforced thermoplastics (gmt) - Determination of flowability and solidification
TS EN 14469-1 Pigments and additives - Determination of coloring agents in poly (vinyl chloride) (pvc-P) with plasticizer - Part 1: Composition and preparation of main mixtures
TS EN 14469-2 Pigments and additives - Determination of colorants in poly (vinyl chloride) (pvc-P) with plasticizer - Part 2: Preparation of test specimens
TS EN 14469-3 Pigments and additives - Determination of coloring agents in poly (vinyl chloride) (pvc-P) with plasticizer - Part 3: Determination of the relative coloring power of white pigments
TS EN 14469-4 Pigments and additives - Determination of colorants in poly (vinyl chloride) (pvc-P) with plasticizer - Part 4: Determination of color flow of colorants
TS EN 14481 Materials and materials in contact with foodstuffs - Plastics - Test methods for the determination of oil contact
TS EN 14510 Adhesives for footwear and leather goods - Solvent based and dispersion adhesives - Determination of soleposition adhesion
TS EN ISO 14526-3 Plastics - Phenolic powder molding mixtures (pf-Pmc) - Part 3: Properties of some molding mixtures
TS EN ISO 14528-1 Plastics - Melamine - Formaldehyde powder molding mixtures (mf-Pmc) - Part 1: System and principles of marking features
TS EN ISO 14528-2 Plastics - Melamine - Formaldehyde powder molding mixtures (mf-Pmc) - Part 2: Preparation of test specimens and determination of their properties
TS EN ISO 14528-3 Plastics - Melamine - Formaldehyde powder molding mixtures (mp-Pmc) - Part 3: Properties of some molding mixtures
TS EN ISO 14529-1 Plastics - Melamine / phenolic powder molding mixtures (mp-Pmc) - Part 1: System and principles for marking properties
TS EN ISO 14529-2 Plastics - Melamine / phenolic powder molding mixtures (mp-Pmc) - Part 2: Preparation of test specimens and determination of properties
TS EN ISO 14530-1 Plastics - Powdered unsaturated polyester molding mixtures (up-Pmcs) - Part 1: Principles for marking system and properties
TS EN ISO 14530-2 Plastics - Powdered unsaturated polyester molding mixtures (up-Pmcs) - Part 2: Preparation of test pieces and determination of properties
TS EN ISO 14530-3 Plastics - Powdered unsaturated polyester molding mixtures (up-Pmcs) - Part 3: Properties of selected molding mixtures
TS EN 14598-1 Reinforced thermosetting pulps - Specification for sheet molding pulp (smc) and bulk molding pulp (bmc) - Part 1: Marking
TS EN 14598-2 Reinforced thermoset pulps - Specification for sheet molding pulp (smc) and bulk molding pulp (bmc) - Part 2: General specifications and test method
TS EN 14598-2 / AC Reinforced thermosetting pulps - Specification for sheet molding pulp (smc) and bulk molding pulp (bmc) - Part 2: General requirements and test methods
TS EN ISO 14663-1 Plastics - Ethylene / vinyl alcohol (evoh) copolymer molding and extruding agents - Part 1: Principles and marking system for specifications
TS EN ISO 14663-2 Plastics- Ethylene / vinyl alcohol (evoh) copolymer molding and extrusion materials- Part 2: Preparation of test pieces and determination of their properties
TS EN ISO 14678 Adhesives - Determination of flow resistance
TS EN ISO 14692-4 Glass fiber reinforced plastic (ctp) pipe systems - Part used in the oil and gas industry 4: Plant, installation and operation
TS EN 14713 Adhesives for paper and cardboard, packaging and disposable sanitary products - Determination of the friction properties of films suitable for adhesion
TS ISO 14848 Plastics - Unsaturated polyester resins - Determination of reactivity at 130ºc
TS EN ISO 14851 (Formerly: TS ISO 14851) Determination of final aerobic biodegradability of plastic materials in aqueous media - Method for measuring oxygen demand in a closed breathing apparatus
TS ISO 14851: 2002 / T1 (Number modification, TS EN ISO 14851) Determination of final aerobic biodegradability of plastic materials in aqueous media - Method for measuring oxygen demand in a closed breathing apparatus
TS EN ISO 14852 (Formerly: TS ISO 14852) Determination of the final aerobic biodegradability of plastic materials in water - Method of determination of released carbon dioxide
TS ISO 14852: 2002 / T1 (Number modification, TS EN ISO 14852) Determination of the final aerobic biodegradability of plastic materials in aqueous media - Method of determination of released carbon dioxide
TS EN ISO 14855-2 Determination of ultimate aerobic biodegradability of plastic materials under controlled composting conditions - Method of analysis of released carbon dioxide - Part 2: Gravimetric measurement of released carbon dioxide
TS EN 14869-2: 2011 Structural adhesives - Determination of shear behavior of structural adhesion zones - Part 2: Shear test on thick adhesion zones
TS EN 14886 Plastic and rubber machines - Cutting with ribbon blades for block foams - Safety rules
TS EN ISO 14896 Plastics - Polyurethane raw materials - Determination of isocyanate
TS EN 14932 Plastics - Flexible thermoplastic films for wrapping packages - Specification and test methods
TS EN 14933 Thermal insulation and light weight filling products for civil engineering applications - Fabricated expanded polystyrene (eps) - Specification
TS EN 14987 Plastics - Evaluation of plastic disposability in wastewater treatment plants - Test scheme for final acceptance and properties
TS EN 14995 Plastics - Evaluation of composition stability - Test chart and properties
TS EN ISO 15013Plastics - Extruded polypropylene (pp) sheets - Specification and test methods
TS ISO 15038 Plastics - Organic-Perester cross-linking reagents for unsaturated polyester thermosetting materials - Determination of active oxygen content
TS EN 15062 Adhesives for leather and footwear materials - Solvent based and dispersed adhesives - Testing adhesion aging under certain conditions
TS EN 15067 Plastic and rubber machines-Edge bending machines for sacks and bags-Safety rules
TS EN ISO 15106-1 Plastics - Film and sheets - Determination of water vapor permeation rate - Part 1: Moisture detection sensor method
TS EN ISO 15106-2 Plastics - Film and sheets - Determination of water vapor permeation rate - Part 2: Infrared radiation detection sensor method
TS EN ISO 15106-3 Plastics - Film and sheets - Determination of water vapor permeation rate - Part 3: Electrolytic detection sensor method
TS EN 15190 Structural adhesives - Test methods for assessing the long-term stability of bonded metallic structures
TS EN ISO 15252-1 Plastics - Epoxy molding mixtures in powder form (ep-Pmc) - Part 1: Marking system and classification principles
TS EN ISO 15252-2 Plastics - Epoxy-based powder molding blends (ep-Pmcs) - Part 2: Specifications for some molding blends
Plastics - Powder epoxy molding mixtures (ep-Pmc) - Part 15252: Limit value of the properties of some molding mixtures
TS EN ISO 15310 Fiber reinforced plastic composites - Determination of in-plane shear modulus by plate twist
TS EN 15336 Adhesives - Determination of breaking time of jointed joints under static load
TS EN 15337 Adhesives - Determination of shear strength of anaerobic adhesives using needle-rings
TS EN 15342 Plastics - Recycled plastics - Characterization of recycled components from polystyrene (ps)
TS EN 15343 Plastics - Recycled plastics - Traceability of plastic recovery, conformity assessment and recovery content
TS EN 15344 Plastics - Recycled plastics - Characterization of recycled components from polyethylene (pe)
TS EN 15416-3 + A1 Adhesives other than phenolic and aminoplastics for load bearing timber structures - Test methods - Part 4: Creep deformation test of samples under cyclic climatic conditions
TS EN ISO 15526-2 Plastics - Polyketon (pk) molding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
TS ISO 15672 Tire and tire additives - determination of total nitrogen content using automatic analyzer
TS ISO 15672 Tire and tire additives - determination of total nitrogen content using automatic analyzer
TS EN 15702 Porous plastics - Cell counter for flexible and stable polyurethane
TS ISO 15853 Thermoplastic materials-Preparation of tubular test pieces for the determination of hydrostatic strength of materials used in injection molding
tst ISO 14855: 1999 Plastics - Determination of decomposition and final aerobic biodegradation under controlled digestion conditions - Method of analysis of released carbon dioxide
TS EN 15865 Adhesives - Determination of torque resistance of anaerobic adhesives in gear accelerators
TS EN ISO 15908 Adhesives - For thermoplastic pipe systems - Test method for the determination of temperature stability of adhesives
TS ISO 17710 Plastics - Polyols used in polyurethane manufacturing - Determination of unsaturation degree by microtitration
TS ISO 19013-1 Rubber hoses and tubes for fuel systems in internal combustion engines - Specifications - Part 1: Diesel fuels
TS ISO 19013-2 Rubber hoses and pipes for fuel systems in internal combustion engines - Specifications - Part 2: Petrol fuels
TS EN ISO 21627-1 Plastics - Epoxy resins - Determination of chlorine content - Part 1: Inorganic chlorine
TS EN ISO 21627-3 Plastics - Epoxy resins - Determination of chlorine content - Part 3: Total chlorine
TS EN ISO 21627-2 Plastics - Epoxy resins - Determination of chlorine content - Part 2: Easily saponifiable chlorine
TS EN ISO 22088-1 Plastics - Determination of resistance to environmental stress cracking - Part 1: General guide
TS EN ISO 22088-6 Plastics - Determination of resistance to environmental stress cracking (wg) - Part 6: Low tensile speed method
TS EN ISO 22088-5 Plastics - Determination of resistance to environmental stress cracking (wg) - Section 5: Deforming method under constant tensile
TS EN ISO 28941-1 Plastics-Poly (phenylene ether) (PPE) molding and extrusion materials-Part 1: Basics for short demonstration systems and features
tst EN ISO 9142 Adhesives - Guide to selection of standard laboratory aging conditions for testing joints
TSE K 124 Flooring strips - Wood-plastic composite material
tst EN ISO 14855-1 Plastics - Determination of degradation and final aerobic biological degradation under controlled digestion conditions - Method of analysis of released carbon dioxide
TS EN 301 / tst T Adhesives - Phenolic and aminoplastic - For wood structures where load resistance is required - Classification and performance characteristics
ISO 8829: 1990Air - Polytetrafluoroethylene (ptfe) hose assemblies - Test methods
ISO 8829: 1990 Aviation - Polytetrafluoroethylene (ptfe) hose assemblies - Test methods
TS EN 13245-2 Plastic - Non-plasticizing polyvinyl chloride (pvc - U) profiles - For building applications - Part 2: PVC-U and pvc-Ue profiles for interior and exterior walls and ceilings