Muayene.com provides testing, auditing and certification services, which are frequently required in services, especially in the following standards, which have become important in recent years.
TS ISO 6552 Automatic steam traps-Definitions of technical terms
TS EN 26704 Automatic steam traps classification
TS EN 727 Plastic pipes and duct systems-Thermoplastic pipes and fittings -Vicat softening temperature (vys) determination
TS EN 26948 Automatic steam traps-Manufacturing and performance characteristic tests
TS EN 637 Plastic pipe systems - Glass fiber reinforced plastic pipes and fittings - Determination of the amount of components - Gravimetric method
TS EN 804Plastic pipe systems-Connector fittings with connections made with solvent adhesives, manufactured by injection molding and used in pressure pipe systems-Determination of short-term hydrostatic internal pressure resistance
TS EN 1054 Plastic pipe systems-Thermoplastic pipe systems used for disposal of waste water-Determination of air tightness of connections
TS EN 1053 Plastic pipe systems - Thermoplastic pipe systems for non-pressure applications Determination of water tightness
TS EN 803 Plastic pipe systems-Injection-molded thermoplastic fittings for elastic sealing rings used in pressure pipes - Determination of short-term internal pressure resistance without axial loads
TS EN 705Plastic pipe systems-Glass fiber reinforced thermoset plastic (grp) pipes and fittings-Regression analysis methods and application
TS EN 705Plastic pipe systems-Glass fiber reinforced thermoset plastic (grp) pipes and fittings-Regression analysis methods and application
TS EN 802Plastic pipes and duct systems-Injection molding thermoplastic fittings -Used in pressurized pipe systems-Determination of maximum deformation by compression
TS EN 579 Plastic pipe systems - Crosslinked polyethylene (pe-X) pipes - Determination of the degree of crosslinking by solvent extraction
TS EN 27841 Automatic steam traps- Determination of vapor loss-Test methods
TS EN 639Pressured concrete pipes, jointing and joining elements general rules
TS EN 744Plastic pipes and duct systems-Thermoplastic pipes-External impact resistance test throughout the environment
TS EN 681-1 Elastomeric seals - for water and drainage applications - Material properties - Part 1: Rubber
TS 1902 EN 588-1 Fiber cement pipes-Section for sewerage and drainage 1: Non-pressure pipes, joint fittings, joint special fittings
TS 6814 EN ISO 1127 Pipes - Stainless steel - Dimensions, tolerances and unit length masses
TS EN 1716 Plastic pipe systems - Polyethylene (pe) drill t - Determination of impact strength for mounted drill t
TS EN 1514-1 Flanges and connections - Dimensions of gaskets according to rated pressures (pn) - Part 1: Non-metal flat gaskets with or without spacers
TS EN 1514-3 Flanges and connections - Dimensions of gaskets according to rated pressures (pn) - Part 3: Ptfe enveloped non-metal gaskets
TS EN 1514-4 Flanges and connections - Dimensions of gaskets according to rated pressures (pn) - Part 4: Specification for corrugated, flat or grooved metal and filled metal seals used with steel flanges
TS EN 1227 Plastic pipe systems glass fiber reinforced thermoset plastic (grp) pipes - Long term maximum relative ring deformation under wet conditions
TS ISO 2016 Capillary brass fittings for copper pipes - Mounting dimensions and tests
TS EN 751-3 Sealing materials - 1 th, 2 and 3 are used for screw metallic connections in contact with all gases and hot water - Part 3: Non-sintered ptfe strips
TS EN 751-2 Sealing materials - 1 th, 2 th and 3 are used for screw metallic connections in contact with hot gases and hot water - Part 2: Non-hardening gasket compounds
TS EN 751-1 Sealing materials-1 th, 2 th and 3 third family used for screw metallic connections in contact with gases and hot water-Part 1: Air-hardening seal compounds
TS ISO 13954 Plastic pipes and fittings - Stripping separation test for electrically melted polyethylene (pe) tools with a nominal outside diameter of 90 mm or greater
TS ISO 13955 Plastic pipes and fittings - Compression test of electrical melted polyethylene (pe) tools
TS EN 1565-1 Plastic pipe systems - Disposal of waste water (hot and cold) - Styrene copolymer mixtures (yellow + pvc) - Part 1: Pipes, fittings and system features
TS EN 1565-1 Plastic pipe systems - Disposal of waste water (hot and cold) - Styrene copolymer mixtures (yellow + pvc) - Part 1: Pipes, fittings and system features
TS EN 12585 Glass plant, pipeline fittings - Pipeline and fittings 1000 - Compatibility and interchangeability
TS ISO 9625 Fittings for mechanical connection - For pressure pipes made of polyethylene - Used for irrigation
TS ISO 9625 Fittings for mechanical connection - For pressure pipes made of polyethylene - Used for irrigation
TS ISO 9854-1 Thermoplastic pipes - Used in the transport of fluids - Determination of pendulum impact strength by Charpy method - Part 1: General test method
TS ISO 9854-2 Thermoplastic pipes - Used for transporting fluids - Determination of pendulum impact strength by Charpy method - Part 2: Test conditions for pipes manufactured from various materials
TS EN 1453-1 Plastic pipe systems - Profiled walls - Used for disposal of indoor wastewater (at high and low temperatures) - Made of polyvinyl chloride (pvc-U) without plasticizer - Part 1 - Pipes and system features
TS ISO 13966 Thermoplastic pipes and fittings - Rated ring stiffness
TS ISO 13966 Thermoplastic pipes and fittings - Rated ring stiffness
TS ISO 8361-1 Thermoplastic pipes and fittings - Water absorption - Part 1: General test method 10.05.2001
TS ISO 8361-2 Thermoplastic pipes and fittings - Water absorption - Part 2: Test conditions for pipes and fittings made of polyvinyl chloride without plasticizer
TS ISO 8361-3 Thermoplastic pipes and fittings - Water absorption - Part 3: Test conditions for pipes and fittings made of acrylonitrile-butadiene-styrene (abs)
TS ISO 13924 Plastic pipes and fittings - Pe / metal transition fittings - Pe drill ts and pe branch saddles - Bending - Tensile cycle test
TS ISO 4433-3 Thermoplastic pipes - Resistance to chemical liquids - Classification - Part 3: Polyurethane (pvc-U) with high impact resistance (pvc-U) and non-chlorinated poly (vinyl chloride) (pvc-C) pipes
TS ISO 4433-4 Thermoplastic pipes - Resistance to chemical fluids - Classification - Part 4: Poly (vinylidene fluoride) (pvdf) pipes
TS ISO 9634 Aerospace - Fluid systems - Dimensions of protective plastic caps and plugs
TS EN 12560-3 Flanges and connections - Gaskets for flanges with short pressure classes - Part 3: Non-metallic ptfe-wound gaskets
TS EN 12560-4 Flanges and connections - Seals for flanges with short pressure classes - Part 4: Corrugated, flat or grooved metallic and filled metallic seals for use with steel flanges
TS EN 12560-5 Flanges and connections - Seals for flanges with short pressure classes - Part 5: Metallic ring connection seals for use with steel flanges
TS EN 12220 Ventilation - for buildings - Ducts - Dimensions of circular flanges for general ventilation
TS EN 1124-1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
TS EN 1124-1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
TS EN 1124-1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
tst ISO 12176-3 Plastic pipes and fittings-Equipment for polyethylene systems with crimping connection-Part 3: Operator identification
TS EN 12734 Irrigation techniques - Quick connection pipes for mobile irrigation systems - Technical characteristics and testing
TS 9464 EN 1761 Rubber hoses and hose assemblies - used for road tankers and fuel delivery
TS EN 12560-1 Flanges and connections - Gaskets for short flanged class flanges - Part 1: Pluggable or non-plug metallic flat seals
TS EN 12560-3 Flanges and connections - Designations for short flange class sizes - Part 3: Seals with metallic PTFE housings
TS EN 12560-4 Flanges and connections - Gaskets for short flanges of class - Part 4: Corrugated flat or grooved metal and filler metal seals for use with steel flanges
TS EN 12560-5 Flanges and connections - Gaskets for short flanges of class - Part 5: Metal ring joints for use in steel flanges
TS EN 1515-2 Flanges and connections-Bolting-Part 2: Classification of bolt materials for steel flanges, pn short notation
TS EN 13052-1 Effect of substances on drinking water-Organic substances-Determination of color and turbidity of water in pipelines-Part 1: Test method
TS EN 13371 Cryogenic tanks-Couplings for cryogenic service
TS EN 1092-4 Flanges and connections - Circular flanges for pipes, valves, fittings and accessories - Pn short flare - part 4: Aluminum alloy flanges
TS EN ISO 14692-2 Glass fiber reinforced plastic (ctp) pipe systems - used in the oil and gas industry - Part 2: Specifications and manufacture
TS EN 10217-1 Steel tubes for welded pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties
TS 5141 EN 12954 Cathodic protection - For embedded or submerged metallic structures - General principles and application for pipelines
TS ISO 13774 Rubber and plastic hoses for internal combustion engine fuels - Flammability test
TS EN 681-3 Elastomeric seals -Used for pipe connections in sewage and drainage applications -Material properties-Part 3: Porous rubber materials
TS EN 681-4 Elastomeric seals -Used for pipe connections in sewage and drainage applications -Material properties-Part 4: Cast polyurethane sealing elements
TS EN ISO 16871 Plastic pipes and duct systems - Plastic pipes and fittings - Direct exposure to natural climatic conditions
TS EN ISO 16871 Plastic pipes and duct systems - Plastic pipes and fittings - Direct exposure to natural climatic conditions
TS EN ISO 14692-1 Oil and gas industry - Glass fiber reinforced plastic pipes - Part 1: Terms, symbols, applications and materials
TS EN ISO 14692-2 Oil and gas industry - Glass fiber reinforced plastic pipes - Part 2: Qualification and manufacturing
TS EN ISO 14692-3 Oil and gas industry - Glass fiber reinforced plastic pipes-Part 3: System design
TS EN ISO 14692-4 Oil and gas industry - Glass fiber reinforced plastic pipes-Part 4: Installation and operation
TS EN ISO 15493 Plastic piping systems for industrial use - Acrylonitrile-Butadiene-Styrene (abs), poly (vinyl chloride) (pvc-U) and chlorinated poly (vinyl chloride) (cpvc) without plasticizer - Properties for systems and components - Metric series (ISO 15493: 2003)
TS EN 1759-3 Flanges and connections-Circular flanges- For pipes, valves, fittings and accessories-Class-specified- Part 3: Copper alloy flanges
TS EN 10301 Steel pipes and fittings for onshore and offshore pipelines - Friction reducing inner lining for the transport of non-corrosive gas
TS EN ISO 10806 Plumbing - Fittings for corrugated, flexible metal hoses
TS EN 561Gas welding equipment - Quick coupling with shut-off valve for welding, cutting and similar operations
TS 10762-1 EN ISO 15875-1 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 1: General
TS 10762-5 EN ISO 15875-5 Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 5: suitability of the system
TS EN ISO 15465 Pipelines - Striped metal hoses and hose assemblies
TS EN 1759-1 Flanges and connections - Circular flanges for pipes, valves, fittings and accessories - Class short designation - Part 1: Steel flanges, nps ½ to nps 24
TS EN ISO 16871 Plastic pipes and ducting systems - Plastic pipes and fittings - Direct (natural) exposure to climatic conditions
TS EN ISO 16871 Plastic pipes and ducting systems - Plastic pipes and fittings - Direct (natural) exposure to climatic conditions
TS EN 13160-4 Leak detection systems - Part 4: Liquid and / or vapor detection systems for use in leachate or intermediate spaces
TS EN 1124-1 / A1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
TS EN 1124-1 / A1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
TS EN 1124-1 / A1 Pipes and fittings - Welded, stainless steel - Used in wastewater systems - Plugs with socket and spigot - Part 1: Features, tests and quality control
TS EN 1759-3 Flanges and connections - Circular flanges for pipes, valves, fittings and accessories - Class short designation - Part 3: Copper alloy flanges
TS EN 10298 Steel pipes and fittings - Used in pipelines laid on land and at sea - Internal surface coating with cement mortar
TS EN 10298 Steel pipes and fittings - Used in pipelines laid on land and at sea - Internal surface coating with cement mortar
TS EN 681-1 / A3 Elastomeric seals for water and drainage applications - Material properties - Part 1: Rubber
TS EN 681-3 / A2 Elastomeric seals -Used for pipe connections in sewage and drainage applications -Material properties-Part 3: Porous rubber materials
TS EN 681-4 / A2 Elastomeric seals -Used for pipe connections in sewage and drainage applications -Material properties-Part 4: Cast polyurethane sealing elements
TS EN 682 / A1 Elastomeric seals - Material properties of gaskets for pipes and fittings used in the transport of gas and hydrocarbon liquids
TS EN 10217-2 / A1 Steel tubes for welded pressure purposes - Technical delivery conditions - Part 2: Electric welded non-alloy and alloy steel tubes with specified high temperature properties
TS EN 10217-1 / A1 Steel tubes for welded pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties
TS EN 1759-3 / AC Flanges and connections - Circular flanges - For pipes, valves, fittings and accessories - Class-specified - Part 3: Copper alloy flanges
TS EN ISO 1167-1 Thermoplastic pipes, fittings and tools-Used for the transport of liquids-Determination of resistance to internal pressure-Part 1: General method
TS EN 14870-3 Oil and gas industry - Pipelines - Hot bent bends, fittings and flanges - Part 3: Flanges
TS EN 1333 Flanges and connections - Pipe fittings - Description and selection of Pn
TS EN ISO 15874-1 / tst A1 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 1: General
TS EN ISO 13478 Thermoplastic pipes - Used for transporting fluids - Determination of resistance to rapid crack propagation
TS EN ISO 14692-4 / AC Oil and gas industry-Glass reinforced plastic (grp) pipes-Part 4: Fabrication, laying and applied processes
TS EN 15152 Railway applications - Windshields for train cabins
TS EN ISO 1167-3 Thermoplastic pipes, fittings and fittings -Used for carrying liquids -Interesting resistance to internal pressure -Preparation of components
TS EN ISO 1167-3 Thermoplastic pipes, fittings and fittings -Used for carrying liquids -Interesting resistance to internal pressure -Preparation of components
TS EN ISO 1167-4 Thermoplastic pipes, fittings and tools-Used for transporting liquids-Determination of resistance to internal pressure-Preparation of tools
TS EN ISO 1167-4 Thermoplastic pipes, fittings and tools-Used for transporting liquids-Determination of resistance to internal pressure-Preparation of tools
TS EN 10217-1 / A1 Steel tubes - Welded - For pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties
tst ISO 12176-4 Plastic pipes and fittings -Equipment for polyethylene systems with crimping connection-Part 4: Conformity coding
tst ISO 12176-4 Plastic pipes and fittings -Equipment for polyethylene systems with crimping connection-Part 4: Conformity coding
TS 821 EN 1916 / AC Concrete pipes and fittings - Unreinforced, steel fiber and reinforced
tst EN ISO 8330 Rubber and plastic hoses and hose assemblies - Terms and definitions
TS EN ISO 13477 Thermoplastic pipes - Used for transporting fluids - Determination of resistance to rapid crack propagation (rpc) - Small scale steady state test (s4 test)
TS EN ISO 4671 Rubber and plastic hose and hose assemblies - Methods for measuring the dimensions of hoses and lengths of hose assemblies
TS EN 13942 Oil and gas industry - Pipeline transport systems - Line valves
TS EN 10298 Steel pipes and fittings - Used in pipelines laid on land and at sea - Internal surface coating with cement mortar
TS EN 10298 Steel pipes and fittings - Used in pipelines laid on land and at sea - Internal surface coating with cement mortar
TS EN 15001-1 Gas systems - Operating pressure for industrial installations larger than 0,5 bar and for industrial and other installations larger than operating pressure 5 bar - Part 1: Detailed information on design, material, construction, inspection and testing functional features
TS EN 969Ductile ductile iron pipes with spheroidal graphite, fittings, fittings and their connections - Specification and test methods for gas pipelines
TS EN 969 Ductile iron pipes with spheroidal graphite, fittings, fittings and their connections - Properties and test methods for gas pipelines
TS EN 10253-3 Butt welded pipe fittings - Part 3: Formable austenitic and austenitic ferritic (duplex) stainless steels without special inspection requirements.
TS EN ISO 15877-2 Plastic pipe systems for hot and cold water systems Chlorinated poly (vinyl chloride) (pvc-C) - Part 2: Pipes
TS EN ISO 4671 Rubber and plastic hose and hose assemblies - Methods for measuring the dimensions of hoses and lengths of hose assemblies
TS EN 15001-1 Gas systems - Operating pressure for industrial installations larger than 0,5 bar and operating pressure for industrial and non-industrial installations larger than 5 bar - Part 1 - Design, material, construction, inspection and testing detailed functional requirements
TS EN 489 Central heating pipes - Pre-insulated pipe systems - Connection set for steel service pipes with polyurethane thermal insulation and polyethylene outer casing used directly in underground hot water networks
TS EN 1092-2 / T1 Flanges and connections - Circular flanges for pipes, valves, fittings and accessories-Pn short flash section 2: Cast iron flanges
TS EN 681-1 / AC Elastomeric seals - For water and drainage applications - Material specifications - Part 1: Rubber
TS EN ISO 1452-1 Plastic pipe systems - for drinking and potable water - Used in underground and surface pressure sewage systems - Polyvinyl chloride (PVC-U) without plasticizer - Part 1: General
TS EN ISO 1452-1 Plastic pipe systems - for drinking and potable water - Used in underground and surface pressure sewage systems - Polyvinyl chloride (PVC-U) without plasticizer - Part 1: General
TS EN 1057 + A1 Copper and copper alloys - Seamless round copper tubes for water and gas transport in health and heating applications
TS EN 13941 + A1 Central heating - Design, installation of pre-insulated bonded pipe systems
TS EN 1447 + A1 Plastic pipe systems - Glass fiber reinforced thermoset plastic (grp) pipes - Determination of long term internal compressive strength
TS EN 545Ductile cast iron pipes - Pipes, fittings, accessories and fittings used in water lines - Specifications and test methods
TS EN 545Ductile cast iron pipes - Pipes, fittings, accessories and fittings used in water lines - Specifications and test methods
TS EN 1591-2 Flanges and connections - Design rules for circular flange connections with gasket - Part 2: Gasket materials
TS EN 1555-1 Plastic pipe systems - For the transport of gas fuels - Polyethylene (pe) - Part 1: General
TS EN 1555-2 Plastic piping systems - Used for the transport of gas fuels - Polyethylene (pe) - Part 2: Pipes
TS EN 1555-5 Plastic pipe systems - Used for the transport of gas fuels - Polyethylene - Part 5: suitability of the system for its purpose
TS EN 1401-1 Plastic pipe systems - For unpressurized, underground drainage and sewage - Made of polyvinylchloride (pvc-U) without plasticizer - Part 1: Pipes, fittings and system features
TS EN 1852-1 Plastic pipe systems - Unpressurized - Used in underground drainage and sewage systems - Polypropylene (pp) - section 1: Pipes, fittings and system features
tst EN 1852-2 Plastic pipe systems - Non-pressurized - Used in underground drainage and sewage systems - Polypropylene (pp) - Section 2: Conformity assessment guide
TS EN ISO 11295 Plastic pipe systems - Used for renovation - classification and design information
TS EN 12115 Rubber and thermoplastic hoses and hose assemblies - For liquid or gaseous chemicals - Specifications
TS EN 681-1 / T1 Elastomeric seals - Used in water and drainage applications - Material specifications - Part 1: Rubber
TS EN ISO 15877-2: 2009 / A1 Plastic piping systems for hot and cold water systems Chlorinated poly (vinyl chloride) (pvc-C) - Part 2: Pipes
TS EN ISO 15877-5 / A1 Plastic pipe systems - For hot and cold water systems - Chlorinated poly (vinyl chloride) (pvc-C) - Part 5: Suitability of the system for its purpose
TS EN ISO 15877-3: 2009 / A1 Plastic piping systems for hot and cold water systems Chlorinated poly (vinyl chloride pvc-C) - Part 3: Fittings
TS EN ISO 10893-1 Non-destructive testing of steel pipes - Part 1: Automatic electromagnetic examination of seamless and welded (excluding submerged arc welding) steel pipes for verification of hydraulic tightness
TS EN ISO 10893-2 Non-destructive testing of steel pipes - Part 2: Automatic eddy current testing of seamless and welded (excluding submerged arc welding) steel pipes for the detection of defects
TS EN ISO 10893-6 Non-destructive testing of steel tubes - Part 6: Radiographic examination of weld seam in welded steel tubes for the detection of defects
TS EN ISO 10893-7 Non-destructive testing of steel pipes - Part 7: Digital radiographic examination of weld seam in welded steel pipes for the detection of defects
TS EN ISO 10893-8 Non-destructive testing of steel pipes - Part 8: Automatic ultrasonic testing of seamless and welded steel pipes for the detection of planar defects
TS EN ISO 10893-10 Non-destructive testing of steel pipes - Part 10: Automatic full environmental ultrasonic testing of seamless and welded (excluding submerged arc welding) steel pipes for the detection of longitudinal and / or transverse defects
TS EN ISO 10893-11 Non-destructive testing of steel pipes - Part 11: Automatic ultrasonic testing of weld seam in welded steel pipes for the detection of transverse and / or longitudinal defects
TS EN ISO 11296-4 Plastic piping systems for the renewal of underground pressure-free drainage and sewage lines - Part 4: Priming with on-site cured pipes
TS EN ISO 11296-4 Plastic piping systems for the renewal of underground pressure-free drainage and sewage lines - Part 4: Priming with on-site cured pipes
TS EN 13942 / AC: 2009Oil and natural gas industry - Pipeline transport systems - Line valves31.01.2012
TS 10672-2 EN ISO 15875-2 / tst A1 -Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 2: Pipes
TS 10672-1 EN ISO 15875-1 / tst A1 -Plastic pipe systems - For hot and cold water - Cross-linked polyethylene (pe-X) - Part 1: General
TS EN ISO 14692-4 / tst AC Glass fiber reinforced plastic (ctp) pipe systems - Part used in the oil and gas industry 4: Plant, installation and operation
TS EN ISO 1452-5 Plastic pipe systems - Used for drinking and potable water, underground and surface pressure drainage and sewage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 5: suitability of the system
TS EN ISO 1452-5 Plastic pipe systems - Used for drinking and potable water, underground and surface pressure drainage and sewage systems - Unplasticized polyvinyl chloride (pvc-U) - Part 5: suitability of the system
TS EN 10253-3 Butt welded pipe fittings - Part 3: Formable austenitic and austenitic-ferritic (duplex) stainless steels without special inspection
TS EN 26801 / A1 Rubber or plastic hoses - Determination of volumetric expansion
TS EN ISO 4671: 2007 / A1 Rubber and plastic hose and hose assemblies - Methods for measuring the dimensions of hoses and lengths of hose assemblies
TS EN 12201-1 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 1: General
TS EN 12201-3 + A1 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 3: Fittings
TS EN 1201-5 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (PE) - Part 5: suitability of the system for its purpose
TS EN ISO 6224 Plastic hoses - For textile reinforced general purpose water applications - Specification
TS EN ISO 15001 Anesthetic and respiratory equipment - Oxygen compatibility
tst EN 10208-1 Pipelines for combustible fluids - Steel pipes - Technical delivery conditions - Part 1: Pipes with class A specification
tst EN 10208-2 Pipelines for combustible fluids - Steel pipes - Technical delivery conditions - Part 2: Pipes with class b specification
TS EN 14624 Performance of mobile leak detectors and room controllers for halogenated refrigerants
TS EN 295-3 Pipes-Clay-Glazed-Joints and joining parts-For waste water and drainage-Part 3: Test methods
TS EN 13480-3: 2012 (EN) Industrial metallic pipes - Part 3: Design and calculation
TS EN 10242 / A2 Pipe fittings - Cast iron tempered, threaded
TS EN 1555-2 Plastic pipe systems - For the transport of gas fuels - Polyethylene (PE) - Part 2: Pipes
TS EN 12201-2 + A1 Plastic pipe systems - For pressurized drinking and potable water, drainage and sewage - polyethylene (PE) - Part 2: Pipes
TS EN 12201-3 + A1 Plastic pipe systems for potable and domestic water, sewage and drainage under pressure - Polyethylene (PE) - Part 3: Fittings
tst EN 12201-1 Plastic pipe systems for potable and utility water, sewage and drainage under pressure - Polyethylene (pe) - Part 1: General
TS 9220 EN 26801 (Number Amendment TS EN 26801: 1993) Rubber and plastic hoses-Determination of volumetric expansion
TS EN 12201-5 Plastic pipe systems - For pressurized drinking and potable water, drainage and sewage - Polyethylene (PE) - Part 5: Suitability of the system for its purpose
TS EN ISO 3994 Plastic hoses - Thermoplastic hoses reinforced in helical form by means of thermoplastic material, used for suction and discharge of aqueous materials - Specification
TS EN 15889 Fire fighting hoses - Test methods
TS ISO 18553 Test method for evaluating the degree of pigment or carbon black dispersion in polyolefin pipes, pipe fittings and compounds
TS ISO 18553 Test method for evaluating the degree of pigment or carbon black dispersion in polyolefin pipes, pipe fittings and compounds
TS ISO 13956 Plastic pipes and fittings - Determination of adhesion strength - Tear test for polyethylene (pe) tools
TS ISO 13956 Plastic pipes and fittings - Determination of adhesion strength - Tear test for polyethylene (pe) tools
TS EN 1555-3: 2010 + A1 Plastic pipe systems - Used for the transport of gas fuels - Polyethylene (pe) - Part 3: Fittings
TS EN ISO 9080 Determination of long term hydrostatic strength of plastic pipes and duct systems thermoplastic pipe materials by extrapolation method
TS EN 1254-6 Copper and copper alloys-Pipe fittings-Part 6: Pushfit terminated connections
TS EN 1254-8 Copper and copper alloys-Pipe fittings-Part 8: Pressure end fittings for use with plastics and multilayer pipes
TS EN ISO 10380 Pipe systems - Corrugated metal hoses and hose assemblies
TS ISO 13781: 2012 (EN) Flexible hose fittings in drinking water installations - Functional features and test methods
TS ISO 11414 Plastic pipes and fittings-Polyethylene (pe) pipe / pipe or pipe / joint part test systems with butt welding
TS ISO 11414 Plastic pipes and fittings-Polyethylene (pe) pipe / pipe or pipe / joint part test systems with butt welding
TS EN 13480-1: 2012 (EN) Industrial metallic tubes - Part 1: General
TS EN 13480-2: 2012 (EN) Industrial metallic tubes - Part 2: Materials
TS EN 13480-4: 2012 (EN) Industrial metallic pipes - Part 4: Manufacturing and installation
TS EN 13480-5 Industrial metallic tubes - Part 5: Inspection and tests
TS EN 13480-6: 2012 (EN) Industrial metallic piping - Part 6: Additional requirements for buried piping
TS EN 13480-8 Industrial piping of metals - Part 8: Additional requirements for aluminum and aluminum alloy piping
TS EN 12007-2 Gas supply systems - Piping - Maximum operating pressure up to 16 bar (included) - Part 2: Special recommendations on function for polyethylene pipelines with maximum operating pressure up to 10 bar (included)
TS EN 12007-4 Gas supply systems - Piping - Highest operating pressure up to and including 16 bar - Part 4: Special functional recommendations for renovation
TS EN 12842 Fittings made of artificial iron for PVC-U or PE pipe systems
TS EN 12450: 2012 Copper and copper alloys - Seamless round capillary copper tubes
TS EN 295-1 Pipes-Clay-Glazed-Fittings and jointing parts-For wastewater and drainage-Part 1: Features
TS EN 295-2 Pipes-Clay-Glazed-Joints and connecting parts-For wastewater and drainage-Part 2: Quality control and sampling
TS EN 295-4 Pipes-Clay-Glazed-Joints and connecting parts-for outdoor wastewater and drainage-Part 4: Special fittings, adapters and compatible hardware-Specifications
TS EN 295-5 Pipes - Fittings and joining parts - Clay glazed - Outdoor - For wastewater and drainage - Part 5: Pipes and glazing pipes made of glazed clay - Specifications
TS EN 295-6 Tubes - Clay - Glazed - Fittings and joining parts - For waste water and drainage - Part 6: Clay - Glazed inspection chimneys - Required features
TS EN 295-7 Tubes - Clay - Glazed - Fittings and joining parts - For wastewater and drainage - Part 7: Properties of glazed clay pipes and joints for pipe feeding
TSE CEN / TS 12666-2Plastic pipe systems - For unpressurized groundwater and drainage - Polyethylene (pe) - Part 2: Conformity assessment guide
TS EN ISO 27509 Oil and gas industries - Compact flange connections with IX sealing ring
TS EN ISO 10147 Pipe and fittings made of cross-linked polyethylene (PE-X) - Determination of gel content and estimation of the degree of cross-linking
TS EN ISO 10147 Pipe and fittings made of cross-linked polyethylene (PE-X) - Determination of gel content and estimation of the degree of cross-linking
TSE CEN / TS 1555-7 Plastic pipe systems - For the transport of gas fuels - Made of polyethylene (pe) - Part 7: Conformity assessment guide
TS EN 12007-1 Gas supply systems - Piping - Highest operating pressure up to and including 16 bar - Part 1: General recommendations on function
TS EN ISO 11296-7 Plastic piping systems for the repair of underground unpressurized discharge and sewer networks - Part 7: Coating with spiral wound pipes
TS EN ISO 11296-7 Plastic piping systems for the repair of underground unpressurized discharge and sewer networks - Part 7: Coating with spiral wound pipes
TS EN ISO 11296-7 Plastic piping systems for the repair of underground unpressurized discharge and sewer networks - Part 7: Coating with spiral wound pipes
TS EN 253 + A1 Central heating pipes - Pre-insulated pipe systems - Directly used in underground hot water networks - Polyurethane heat insulated, polyethylene outer casing steel service pipe systems
TS EN 1796 Plastic pipe systems - For pressurized or unpressurized water supply - Unsaturated polyester resin (UP) based glass reinforced thermoset plastic (GRP)
TS EN ISO 11299-1 Pipe systems for the renewal of underground gas networks Plastic - Part 1: General
TS EN ISO 11299-1 Pipe systems for the renewal of underground gas networks Plastic - Part 1: General
TS EN ISO 11299-3: 2013 Pipe systems for renewal of underground gas networks Plastic - Part 3: Liner with narrow-fit pipes
TS EN ISO 11299-3: 2013 Pipe systems for renewal of underground gas networks Plastic - Part 3: Liner with narrow-fit pipes
TS EN ISO 15874-1 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 1: General
TS EN ISO 15874-2 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 2: Pipes
TS EN ISO 15874-3 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 3: Fittings
TS EN ISO 15874-5 Plastic piping systems for hot and cold water - Polypropylene (pp) - Part 5: System suitability
TS EN ISO 9311-2 Adhesives - for thermoplastic pipe systems - Part 2: Determination of shear strength
TS EN ISO 13260 Thermoplastic pipe systems for unpressurized underground drainage and waste water - Simultaneous temperature cycling and external load resistance test method
TS EN ISO 13260 Thermoplastic pipe systems for unpressurized underground drainage and waste water - Simultaneous temperature cycling and external load resistance test method
TS EN 805Su supply - Specification for outdoor components and systems
TS EN 1112 Sanitary fittings - Shower heads for Type 1 and Type 2 water supply systems - General specifications
TS EN 15012 Plastic pipe systems - Soil and waste discharge systems in the building - Performance characteristics for pipes, fittings and fittings
TSE CEN ISO / TS 21003-7 / A1 Multilayer pipe systems for indoor hot and cold water installations - Part 7: Guidelines for conformity assessment
TS EN ISO 7369 Pipe systems - Metal hoses and hose assemblies - Terms
TS EN ISO 19879 Metallic pipe connections for fluid power and general use - Test methods for hydraulic fluid power connections
TS EN 1971-2 Copper and copper alloys - Eddy current inspection for the measurement of defects in seamless round copper and copper alloy pipes - Part 2: Internal probe method on the inner surface
TS EN 12452: 2012 Copper and copper alloys - Seamless tubes with extruded ducts for heat exchangers
TS EN 13083 + A1 Tanks for transporting dangerous goods Service equipment used in tanks Vapor transmission valve
TS EN 14422 Clamp type clamping kits for liquefied petroleum gas (LPG) transfer hoses
TS EN 14424 Hose connections - With screw ferrules
TS EN 16348 Gas infrastructure - Safety management system for pipeline operating system for gas transport infrastructure and gas transport pipelines - Functional features
TS EN ISO 11297-1 Plastic piping systems - For the renovation of underground drainage and sewerage networks under pressure - Part 1: General
TSE CEN / TS 14541 Plastic pipes and fittings - Used PVC-U, PP and PE materials
TS EN 1360 Rubber and plastic hoses and hose assemblies - For metered fuel distribution units - Specification
TS EN ISO 11297-3 Plastic pipe systems - For the renovation of underground drainage and sewerage networks under pressure - Part 3: Laying with crimped pipes
TS EN 13483 Rubber and plastic hose and hose assemblies - Internal steam recovery in metered fuel distribution systems - Features
TS EN 14420-7 Hose connections and clamping units section 7: Cam-lock couplings
TS EN 14420-1 Hose connections and clamping units section 1: Features, types of fastening and jointing, inspection, marking and tests
TS EN 14420-2 Hose connections and clamping units section 2: Hose end edges
TS EN 14420-3 Hose connections and clamping units - Part 3: Clamping units, bolted or with pin
TS EN 14420-4 Hose connections and clamping units section 4: Flanged connections
TS EN 14420-5 Hose connections and clamping units section 5: Threaded connections
TS EN 14420-6 Hose connections and clamping units section 6: Tw tanker couplings
TS EN ISO 11297-1 Plastic piping systems - For the renovation of underground drainage and sewerage networks under pressure - Part 1: General
TSE CEN / TS 14541 Plastic pipes and fittings - Used PVC-U, PP and PE materials
TS EN ISO 11297-3 Plastic pipe systems - For the renovation of underground drainage and sewerage networks under pressure - Part 3: Laying with crimped pipes
TS EN ISO 27509: 2012 / AC Oil and gas industries - Flange connections compatible with IX sealing ring
TS EN 1594 Gas supply systems - Pipelines - Maximum operating pressure above 16 bar - Functional specifications
TS EN 12573-4 Welded, static, unpressurized thermoplastic tanks - Part 4: Design and calculation for flanged connections
TS EN 253 + A1 Central heating pipes - Pre-insulated pipe systems - Directly used in underground hot water networks - Polyurethane heat insulated, polyethylene outer casing steel service pipe systems
TS EN 13480-2 / A1 Industrial metallic tubes - Part 2: Materials
TS EN 13480-4 / A1 Industrial metallic pipes - Part 4: Manufacturing and installation