We carry out your testing and inspection procedures in accordance with the following standards of services in accordance with national and international regulations and standards. We serve all the standards below.
TS ISO 5598 Fluid power systems and components-Terms
TS ISO 5599-1 Pneumatic fluid power-Five-port directional control valves - Part 1: Mounting interfaces - Excluding electrical connections
TS ISO 6432 Pneumatic fluid power-Cylinders with piston rod from one side-1000 kpa (10 bar) series-Piston diameter 8 mm - 25 mm connection dimensions
TS EN ISO 9974-2 Fasteners - for general purpose and fluid power - Threaded, elastomer-sealed or metal-tight connections and connectors according to ISO 261-Section 2: Flanges with elastomer seal (type e)
TS EN 4021 Aviation series-Titanium alloy pipe joint 8 ° 30-Corners 90 °, bulkhead
TS ISO 4392-1 Hydraulic fluid power - Determination of the characteristics of the motors Part 1: Constant low speed and constant pressure
TS ISO 4392-2 Hydraulic fluid power - Determination of the characteristics of the motors Part 2: Mobility
TS ISO 4392-3 Hydraulic fluid power - Determination of the characteristics of the motors Part 3: At constant flow and constant torque
TS ISO 4412-1 Hydraulic fluid power-Test code for the determination of airborne noise level section 1: Pumps
TS ISO 4412-2 Hydraulic fluid power-Test code for the determination of airborne noise level section 2: Engines
TS ISO 4412-3 Hydraulic fluid power - Test code for the determination of airborne noise level section 1: Pumps - Method with parallel array microphone
TS ISO 8426 Hydraulic fluid power-Positive displacement pumps and motors- Capacity determination
TS ISO 10767-1 Hydraulic fluid power - Determination of pressure, fluctuation levels produced in systems and components - Part 1: Precision method for pumps
TS ISO 10767-2 Hydraulic fluid power - Determination of pressure, fluctuation levels generated in systems and components - Part 2: Simplified method for pumps
TS ISO 10767-3 Hydraulic fluid power - Determination of pressure, fluctuation levels generated in systems and components - Part 3: Method for motors
TS ISO 17559 Hydraulic - Fluid power - Electrically controlled hydraulic pumps - Test methods for determining performance characteristics
TS ISO 4394-1 Fluid power systems and components -Cylinder tubes section Features of specially machined steel tubes inside 1
TS ISO 10099 Pneumatic fluid power - Cylinders - Final inspection and acceptance criteria
TS ISO 10100 Hydraulic fluid power-Cylinders-Acceptance tests
tst ISO / TS 13725 Hydraulic fluid power - Cylinders - Method for determination of bending load
TS ISO 13726 Hydraulic fluid power piston One-side piston rod cylinders, 250 mm to 500 mm tube diameter, 16 MPa (160 bar) compact series - Connection sizes for accessories
TS ISO 7789 Hydraulic fluid power - Two, three and four outlet screw connection bore valves - Cavities
TS ISO 7790 Hydraulic fluid power - Four-way directional control valves with dimensions 02,03 and 05 - Coupling dimensions
TS ISO 12238 Pneumatic fluid power - Directional control valves - Measurement of change time
TS ISO 10771-1 Hydraulic fluid power-Fatigue pressure test of metal casings operating under pressure
TS ISO 5784-1 Fluid power systems and components - Fluid logic circuits - Part 1: Symbols for binary logic and related operations
TS ISO 5784-2 Fluid power systems and components - Fluid logic circuits - Part 2: Feed and discharge symbols for logic symbols
TS ISO 5784-3 Fluid power systems and components - Fluid logic circuits - Part 3: Logic sequencers and symbols for related functions
TS ISO 16656 Hydraulic fluid power - Short stroke cylinders with 10 mm to 100 mm pipe diameter, single piston rod, used in 32 mpa (100 bar) - Mounting dimensions
TS EN 809 + A1 Pumps and pump units - for liquids - General safety regulations
TS EN 809 + A1 / AC Pumps and pumping units - for liquids - General safety regulations
TS EN 16644 Pumps - Rotodynamic pumps - Non-shaft recirculation pumps with rated power input not exceeding 200 W for heating installations and domestic hot water installations - Noise test code for measuring structural and liquid-induced noise (vibration acoustics)
TS ISO 3069 Centrifugal pumps-End suction-Mechanical type seals and shaft seals-Housing dimensions
TS EN ISO 20361 Liquid pumps and pump units-Noise test code-Accuracy class 2 and accuracy class 3
TS EN ISO 14414 Pump system, energy rating
TS EN 14710-1 + A2 Fire-fighting pumps - Non-primer centrifugal pumps for fire-fighting - Part 1: Classification, general and safety rules
TS EN 14710-2 + A2 Fire-fighting pumps - Non-primer centrifugal pumps for fire-fighting - Part 2: Verification of general and safety rules
TS EN 16480 Pumps - Minimum required efficiency of rotodynamic water pumps
TS EN 16752 Centrifugal pumps - test procedure for seal packagings
TS EN 16480 Pumps - Minimum required efficiency of rotodynamic water pumps
tst EN ISO 20361 Liquid pumps and pump units-Noise test code-Accuracy class 2 and accuracy class 3
TS EN 734 Pumps - Side channel - Star impeller - Pn 40 rated working conditions, main dimensions, naming system
TS EN 735Pumps-Rotodynamic type-Tolerances on basic dimensions
TS EN 809 + A1 Pumps and pump units - for liquids - General safety rules
tst EN 1151 Pumps - Centrifugal - Used for water circulation in heating and using hot water plants - Up to 200 w - Specifications, tests and marking
TS 1406-1 ISO 1607-1 Vacuum pumps - Positive displacement - Measurement of performance characteristics - Part 1: Measurement of volumetric flow (pumping speed)
TS 1406-2 ISO 1607-2 Vacuum pumps - Positive displacement - Measurement of performance characteristics - Part 2: Measurement of final pressure
TS 1407-1 ISO 1608-1 Vacuum pumps - Measurement of performance characteristics for steam - Part 1: Measurement of volumetric flow (pumping speed)
TS 1407-2 ISO 1608-2 Vacuum pumps - Steam - Measurement of performance characteristics - Part 2: Measurement of critical auxiliary pressure
TS ISO 3529-2 Vacuum technology - Terms and definitions - Part 2: Vacuum pumps and related terms
TS EN ISO 5198 Pumps - Centrifugal, mixed flow and axial, code for hydraulic performance tests - Accuracy class
TS EN ISO 9908 Centrifugal pumps - Technical specifications - Class III
TS EN ISO 9908: 1997 / A1: 2011 Centrifugal pumps - Technical specifications - Class III
TS EN 1012-1 Compressors and vacuum pumps - Safety rules - part 1: Air compressors
TS EN 12157 Rotodynamic pumps - Cooling pump units - For machine tools - Nominal flow rate, dimensions
TS EN 12162 + A1 Liquid pumps - Safety requirements - Hydrostatic test procedure
TS EN 12262 Rotodynamic pumps - Technical documents - Terms, delivery range and plan
TS EN 12462 Pumps - Performance criteria for biotechnological pumps
TS EN 12483 Liquid Pumps - Frequency Inverter Pump Units - Warranty and compatibility tests
TS EN 12639 / tst AC: 2004 Liquid pumps and pumping units - Noise test code - Accuracy quality 2 and accuracy quality 3
TS EN 12639 / tst AC: 2000 Liquid pumps and pumping units - Noise test code - Accuracy quality 2 and accuracy quality 3
TS EN 14343 Rotary positive displacement pumps - Performance tests for acceptance
TS EN 14343 / AC Rotary positive displacement pumps - Performance tests for acceptance
TS EN 14710-2 + A2 Fire-fighting pumps - Non-primer centrifugal pumps for fire-fighting - Part 2: Verification of general and safety rules
TS EN ISO 14847 Rotary pumps with positive displacement specifications
TS EN ISO 15783 / A1 Pumps - Sealed-Rotodynamic-Class II_ specifications
TS EN ISO 16330 Piston pumps and pump units - Technical rules
TS EN ISO 21049 Pumps - Shaft sealing systems of centrifugal and rotary pumps
TS EN ISO 3661 (Former no: TS EN 23661) Pumps centrifugal centrifugal pumps with central suction
TS EN 23661 / T1 (Number Modification, TS EN ISO 3661) Pumps with centrifugal centrifugal centrifugal pumps - Base and mounting dimensions
TS EN 45510-5-4 Power plants-Supply guide for equipment-Section 5-4: Water turbines, piston pumps and turbo pumps
TS EN 45510-6-4 Power plants - Supply guide for equipment part 6-4: Turbine auxiliary devices - Pumps
TS EN 60041 Site acceptance tests for the determination of hydraulic performance of hydraulic turbines, storage pumps and turbine-pumps