Electronic Standards

Most of the products used by almost all of the world are electronic devices. While this is important, we pass on the testing, auditing and certification services in this sector. Our company performs the testing, auditing and certification of all the standards mentioned below.

TS EN 60603-10 (Formerly: TS IEC 603-10) Connectors-Section used in printed circuit boards at frequencies below 3 mhz 10: Two-piece connectors used in 2,54 mm basic grid printed circuit boards reverse type

TS EN 60603-9 (Formerly: TS IEC 603-9) Connectors-3 two-piece connectors, back panels and cable connectors for frequencies below MHz, used in printed circuit boards

TS EN 60603-12 (Formerly: TS IEC 603-12) Connectors-Section used in printed circuit boards at frequencies below 3 mhz 12: Dimension, general specifications and detailed specifications for the group of female connectors designed for use in integrated circuits

TS EN 60603-13 (Formerly no: TS IEC 603-13) Connectors-For frequencies below 3 MHz, the group 13: used for printed circuit boards with a base grid of 2,54 mm cannot be accessed with a group of evaluated two-piece connectors of rated quality. detail specification for free connectors with insulating stripper terminals (ys)

TS EN 61249-5-1 Materials for interconnection structures - Part 5: Particle group for coated and uncoated conductive foils and films - Part 1: Copper foils (for manufacturers of copper-plated base materials)

TS EN 61249-5-4 Materials for interconnection structures - Part 5: Partial property group for coated and uncoated conductive foils and films 4: Conductive inks

TS EN 61249-8-7 Materials for interconnection structures - Part 8: Particle group for non-conductive films and coatings - Part 7: Marking inks

TS EN 61319-1 + A11 Interconnection of satellite receivers - Part 1: Europe

TS EN 111000 General specifications - Cathode ray tubes

TS EN 111001 Empty detail specifications-Cathode ray tubes

TS EN 111100 Part specifications - Image storage tubes

TS EN 111101 Empty detail specifications - Image storage tubes

TS EN 112000 General specifications: Image converter and image intensifier tubes

TS EN 112001 Blank detail specifications, image converter and image intensifier tubes

TS EN 113000 General specifications, camera tubes

TS EN 114000 General specifications, picture multiplexing tubes

TS EN 114001 empty detail specification picture multiplexer tubes

TS EN 120001 Empty detail features: Light emitting diodes, light emitting diode arrays, light emitting diode indicators without internal logic and resistors

TS EN 120002 Empty detail features: Infrared light emitting diodes, infrared light emitting diode arrays

TS EN 120003 Blank detail specification: Phototransistors, photo darlington transistors, phototransistors

TS EN 120004 Blank detail specification: Phototransistors with phototransistor output media declared value

TS EN 120005 Blank detail specification: Photodiodes photodiode arrays (not used in fiber optic applications)

TS EN 120007 Blank detail features: Liquid crystal displays, monochrome lcd without electronic circuit

TS EN 137000 General specifications: Non-solid electrolyte fixed aluminum electrolytic alternating current capacitors used in motors

TS EN 137100 Part features: Quality approval of non-solid electrolyte fixed aluminum electrolytic alternating current capacitors for motor starting applications

TS EN 137101 Blank detail specification for non-solid electrolyte, fixed, aluminum electrolytic alternating current capacitors used in motor starting applications

TS EN 143001 Empty detail features: Direct heating negative temperature coefficient thermistors (beads in solid glass or vitrified enamel)

TS EN 143002 Blank detail specification: Directly heated negative temperature coefficient thermistors (beads in envelope)

TS EN 143003 Blank detail specification: Direct heated negative temperature coefficient thermistors (disc type)

TS EN 143004 Blank detail specification: Direct heated negative temperature coefficient thermistors (rod type)

TS EN 60931-2 Capacitors - Non-repairable shunt power capacitors for alternating current systems with rated voltage up to and including 1 kv section 2: Aging and damage test

TS EN 165000-1 Film and hybrid integrated circuits - Part 1: General features: Qualification approval process

TS EN 165000-2 Film and hybrid integrated circuits-Part 2: Internal visual inspection and special tests

TS EN 165000-3 Film and hybrid integrated circuits-Part 3: Final account checklist and report for film and integrated circuit manufacturers

TS EN 165000-4 Film and hybrid integrated circuits - Part 4: Customer information, product evaluation level plans and empty detail specifications

TS EN 168101 Blank detail specification: Quartz crystal units (qualification acceptance)

TS EN 168201 Blank detail specification: Quartz crystal units (quality approval)

TS EN 61076-4 Qualified connectors for direct current (da), low frequency analog and digital high speed data applications - Part 4: Partial specifications - Printed circuit connectors

TS EN 169201 Blank detail specification: Quartz crystal controlled oscillators (quality approval)

TS EN 60444-1 Measurement of quartz crystal unit parameters in a network by zero phase technique - Part 1

TS EN 60512-16-20 Electromechanical components of electronic devices - Basic test procedures and measuring methods - Part 16: Mechanical tests to be applied to contacts with terminals - Part 20: Test 16t: Mechanical durability ((wired terminals of solderless connections)

TS EN 60931-3 Capacitors - Non-repairable shunt power capacitors for alternating current systems with rated voltage up to and including 1 kv - Part 3: Internal fuses

TS EN 61270-1 Condensers for microwave ovens - Part 1: General

TS EN 61797-1 Transformers and coils for telecommunication and electronic devices - Intermediate dimensions of winding formers - Part 1: Winding formers for layered cores

TS EN 62326-4 Printed circuit boards - Part 4: Rigid multi-layer printed circuit boards with intermediate layer connections - Part specifications

TS EN 62326-4-1 Printed circuit boards - Part 4: Rigid multilayer printed circuit boards with intermediate layer connections - Part specifications - Part 1: Capability detail specifications - Performance level a, b and c

TS EN 61751 Laser units used in communication-Safety evaluation

TS EN 165000-5 Film and hybrid integrated circuits - Part 5: Qualification approval method

TS EN 60368-2-2 Piezoelectric sieves - Part 2: Operating instructions for piezoelectric sieves - Part 2: Piezoelectric ceramic sieves (IEC60368-2-2: 1999)

TS 3558 EN 60110-1 Power capacitors for induction heating systems - Part 1: General

TS EN 60931-1 Capacitors - Non-repairable shunt power capacitors for alternative current systems with rated voltage up to and including 1 kv section 1: General - Performance, tests and declaration values - Safety regulations - Plant and operating instructions

TS EN 60825-4 Safety of laser products - Part 4: Laser protectors

TS EN 130102 Gap detail specification standard - Constant polyethylene for direct current - Terephtolate film dielectric metal sheet capacitors - E2 - Rating level

50065-4-1 TS EN 3-148,5-4 Signing in low voltage electrical installations with frequency range 1 kHz to XNUMX khz - part XNUMX - XNUMX: Low voltage separation filters; General features

TS EN 50065-4-2 Signals in low-voltage electrical installations in the frequency range 3 khz to 148,5 khz-Section 4-2: Low-voltage separation filters-Safety rules

TS EN 60191-6-3 Mechanical standardization of semiconductor devices - Part 6-3: General rules for the preparation of draft drawings of surface mounted semiconductor device packages - Measurement methods for the dimensions of quadrature flat packages (qfp)

TS EN 60191-6-6 Mechanical standardization of semiconductor devices - Part 6-6: General rules for the preparation of draft drawings of surface-mounted semiconductor device packages

TS EN 60322 Railway applications - Electronic equipment for railway vehicles - Rules for open structured power resistors (IEC 60322: 2001)

TS EN 60512-23-3 Electromechanical components for electronic devices - Basic test procedures and measuring methods - Part 23-3: Test 23c: Screening efficiency of connectors and accessories

TS EN 61076-7 Connectors - Used in low frequency analog and digital high speed data applications - Part 7: Quality approved non-cable installations - Includes quality and capability approval - Part specifications

TS EN 61943 Integration circuits - Manufacturing application guide

TS EN 170100 Part feature standard - Waveguide type dielectric resonators

TS EN 170101 Cavity - Dielectric resonators with waveguides - Capability approval

TS EN 61747-1 Liquid crystal and solid state display devices - Part 1: General feature

TS EN 61270-1 Capacitors for microwave ovens - part 1: General

TS EN 60368-4-1 Piezoelectric filters with quality assessment - Part 4-1: Blank detail specification - Capability approval

TS EN 60512-6-4 Connectors for electronic devices-Tests and measurements-Section 6-4: Dynamic stress tests-Test 6d: Vibration (sinusoidal)

TS EN 60512-11-12 Connectors for electronic devices - Tests and measurements - Part 11-12. air conditioning experiments; Experiment 11m; Age, temperature, cyclic

TS EN 60512-11-2 Connectors for electronic devices-Tests and measurements-Section 11-2: Air conditioning tests-Test 11b: Combined consecutive cold, low air pressure and wet temperature test

TS EN 61076-2-102 Connectors for electronic devices - Part 2-102: Circular connectors with quality evaluation; Detail feature of plugs and jacks for external low fall supply

TS EN 61076-4-100 Connectors for electronic devices - Part 4-100 quality rated printed circuit connectors - Test feature for two-section connector modules with 2,5 mm grid for printed circuits and back sides

TS EN 61076-4-101 Connectors for electronic devices - Part 4-101 quality rated printed circuit connectors-Iec Detail specification for two-section connector modules with 60917 mm basic grating for 2,0-printed circuits and back sides

TS EN 60512-11-3 Connectors for electronic devices - Tests and measurements - Part 11-3: Air conditioning tests; Experiment 11c: Wet temperature, steady state

TS EN 60512-11-5 Connectors for electronic devices-Tests and measurements-Part 11-5: Air conditioning tests-Test 11e: Mold

TS EN 61076-4-107 Fasteners for electrical devices - Part 4-107: Quality-assessed printed plate fasteners - Two-piece fasteners for 2,0 mm basic screened shields with soldered and crimped inserts for printed boards with inaccessible insulating displacement and crimped ends Detail feature standard

TS EN 61076-4-108 Fasteners for electrical equipment - Part 4-108: Quality assessed printed plate fasteners - Integrated screening function for 60917 mm transverse package density with 1 mm grating according to IEC 2,5-15 and Detail specification standard for cable-to-plate connectors with 25 mm module bore arrangement

TS EN 61076-4-110 Connectors for electronic equipment - Part 4-110: Printed circuit connectors of evaluated quality; Detail feature for fully armored and locking cable tie with fastening function with a grid of at least 2 mm

TS EN 61076-4-111 Connectors for electrical equipment - Part 4-111: Quality-assessed printed plate connectors Two-part power for printed plates and backplanes with 60917 mm grating and quick-coupling according to IEC 1-2,5 Detail feature standard for connector modules

TS EN 60512-25-2 Connectors for electronic devices-Tests and measurements-Section 25-2: Test 25b: Attenuation (loss of insertion)

TS EN 61193-1 Quality assessment systems - Part 1: Analysis and analysis of printed plate systems

TS EN 61249-2-18 Materials for printed plates and other interconnection structures - Part 2-4: Reinforced base material - Coated and uncoated - Reinforced copper-coated non-woven fiberglass reinforced sheet (vertical combustion test) (ic 61249-2) -18: 2001) 10.11.2002

TS EN 61249-2-19 Materials for printed plates and other interconnection structures - Part 2-19: Reinforced base material - Coated and uncoated - Reinforced laminated sheet coated with epoxy cross-folded linear fibercam (vertical combustion test) (icec) 61249-2-19: 2001)

TS EN 61249-2-4 Materials for printed plates and other interconnection structures - Part 2-4: Reinforced base material - Coated and uncoated - Flammable copper-coated polyester textured / nonwoven fibercam laminated sheet (vertical combustion test) (ic 61249-) 2-4: 2001)

TS EN 61249-2-7 Materials for printed plates and other interconnection structures - Part 2-7: Reinforced uncoated and base material coatings - Copper and coated epoxy e-Glass laminated sheet with determined flammability

TS EN 60747-16-1 Semiconductor devices-Section 16-1: Integrated microwave circuits-Amplifiers

TS EN 60747-16-3 Semiconductor devices-Section 16-3: Integrated microwave circuits-Frequency converters

TS EN 60749-10 Semiconductor devices-Mechanical and air conditioning tests-Part 10: Mechanical impact

TS EN 60749-11 Semiconductor devices - Mechanical and air conditioning test methods - Part 11: Rapid temperature change - Dual liquid bath method

TS EN 60749-12 Semiconductor devices-Mechanical and air conditioning tests-Part 12: Vibration, variable frequency

TS EN 60749-13 Semiconductor devices-Mechanical and air conditioning tests and methods-Part 13: Saline atmosphere

TS EN 60749-2 Semiconductor devices - Mechanical and air conditioning tests - Part 2: Low air pressure

TS EN ISO 13696 Optical and optical measuring instruments - Test methods for the scattering of optical components

TS EN 60749-3 Semiconductor devices - Air conditioning and mechanical test method - Part 3: External visual inspection

TS EN 60749-4 Semiconductor devices - Mechanical and air conditioning test methods - Part 4: Wet temperature steady state, highly accelerated strain test (hast)

TS EN 60749-6 Semiconductor devices - Mechanical and air conditioning test methods - Part 6: Storage at high temperatures

TS EN 60749-9 Semiconductor devices - Mechanical and air conditioning test methods - Part 9: Persistence of marking

TS EN 61523-1 Delay and power calculation standards - Part 1: Integrated circuit delay and power calculation systems

TS EN 61643-321 Components for low-voltage surge protection devices - Part 2: Properties for avalanche refraction diodes (USA)

TS EN 60191-6-1 Mechanical standardization of semiconductor devices - Part 6-1: General rules for the preparation of sketches of packages for surface mounted semiconductor devices - Design guide for seagull wing terminals

TS EN 60191-6-2 Mechanical standardization of semiconductor devices - Part 6-2: General rules for the preparation of draft drawings of packs of surface-mounted semiconductor devices-1,50 mm, 1,27 mm and 1,00 mm Design guide for packages

TS EN 60191-6-5 Mechanical standardization for semiconductor devices -General rules for the preparation of draft drawings of surface-mounted semiconductor device packages-Design guide for the grid layout of thin holes

TS EN 60191-6-8 Mechanical standardization of semiconductor devices - Part 6-18: General rules for the preparation of surface-mounted semiconductor device packages - Design guide for glass with ceramic sealing element (G-QFP)

TS EN 61967-1 Integrated circuits-150 kHz to 1 ghz -Measurement of electromagnetic propagation-Section 1. general terms and recipes

TS EN 61967-4 Integrated circuits-150 kHz to 1 gHz measurement of electromagnetic emission-Part 4: Measurement of transmitted emission-1 / 150 direct coupling method

TS 2663 EN 60139 Preparation of external dimension drawings of connections and indicators of cathode ray tube elements

TS EN 60938-2-1 Stationary inductors for suppressing electromagnetic interference - part 2-1: Blank detail specification standard - Inductors where safety tests are required - Rating rating d

TS EN 60938-2-2 Stationary inductors for suppressing electromagnetic interference - Part 2-2: Blank detail specification standard - Inductors where safety tests are required (only)

TS 11285 EN 60603-4 Connectors-for use on printed plates at frequencies below 3 mhz-Section 4: Two-piece connectors for printed plates with contacts between 1.91 mm (0.075 inches) between centers and in the same spacing

TS 11438 EN 60603-5 Connectors-for use on printed plates at frequencies below 3 mhz-Section 5: 2.54: two-piece connectors with end sockets for double-sided printed sheets spaced mm (0.1 inches)

TS 11525 EN 60603-6 Connectors-for use on printed plates at frequencies below 3 mhz-Section: 6 mm (1.6 inch) contact spaced end connectors for single or double-sided printed plates with nominal thickness 0.063 mm and printed sheet binders

TS EN 60747-5-1 Individual semiconductor devices and integrated circuits-Part 5-1: Optoelectronic devices-General

TS EN 60747-5-2 Individual semiconductor devices and integrated circuits - Part 5-2: Optoelectronic devices - Basic limit values and characteristics

TS EN 60747-5-3 Individual semiconductor devices and integrated circuits - Part 5-3: Optoelectronic devices - Measurement methods

TS 11284 EN 60603-3 Connectors-for use on printed plates at frequencies below 3 mhz-Section 3: Two-piece connectors for printed plates with contacts between 2,54 mm (0,100 inches) between the centers and the same spaced-apart terminations

TS EN 60679-5 Quartz crystal controlled oscillators -Quality control made-Part 5: Part feature-Quality approval

TS EN 60679-5-1 Quartz crystal controlled oscillators -Quality control made-Part 5: Blank detail feature -Quality approval

TS EN 61190-1-1 Fastening materials for electronic assembly - part 1-1: Characteristics of solder paste used for high quality interconnections in electronic assemblies

TS EN 122003 Blank detail specifications and capacity approval with standard specification for standard production for the preparation of customer detail specifications

TS EN ISO 17526 Optical and optical instruments - Laser and laser-related equipment - Laser life

TS EN 60191-6-4 Mechanical standardization of semiconductor circuits - Part 6-4: General rules for the preparation of master plan drawings of surface mounted semiconductor circuit packages - Measuring methods for package measurements of round grid array (BGA)

TS EN 60352-7 Solderless connections - Part 7: Spring clamp connections - General rules, test methods and application guide

TS EN 60368-4 Quality assessed piezoelectric filters section 4: Section feature - Capability approval

TS EN 60368-4-1 Piezoelectric filters with quality assessment - Part 4-1: Blank detail specification - Capability approval

TS EN 60512-2-5 Connectors for electronic devices - Tests and measurements - Part 2-5: Electrical continuity and contact resistance tests - Test 2e: Contact disturbance

TS EN 60512-4-1 Connectors for electronic devices - Tests and measurements - Part 4-1: Tensile strength tests - Test 4a: Voltage resistance

TS EN 60749-1 Semiconductor circuits - Mechanical and climate test methods - Section 1: General

TS EN 60749-5 Semiconductor circuits - Mechanical and climate test methods - Part 5: Continuous state temperature humidity slope (bias) life test

TS EN 60749-8 Semiconductor circuits - Mechanical and climatic test methods - Section 8: Sealing

TS EN 60749-16 "semiconductor devices - Mechanical and climatic test methods - part 16: Particle impact noise detection (PIND)"

TS EN 60749-17 Semiconductor circuits - Mechanical and climate test methods - Section 17: Neutron radiation

TS EN 60749-18 Semiconductor circuits - Mechanical and climate test methods - Section 18: Ionizing radiation (total dose)

TS EN 60749-19 Semiconductor circuits - Mechanical and climatic test methods - Section 19: Die shear intensity

TS EN 60749-22 Semiconductor circuits - Mechanical and climate test methods - Part 22: Bond strength

TS EN 60749-31 Semiconductor circuits - Mechanical and climate test methods - Section 31: Flammability of plastic encapsulated circuits

TS EN 60749-32 Semiconductor circuits - Mechanical and climate test methods - Section 31: Flammability of plastic encapsulated circuits

TS EN 60749-36 Semiconductor circuits - Mechanical and climatic test methods - Section 36: Acceleration, steady state

TS EN ISO 15367-1 Laser and laser-related equipment - Test methods for determining the shape of the laser beam waveform - Part 1: Terms, descriptions and key features

TS EN 61921 Power capacitors - Low voltage power factor correction groups

TS EN 61921 Power capacitors - Low voltage power factor correction sets

TS EN 50065-4-2 / A1Signation in low voltage electrical installations - in the frequency range 3 khz to 148,5 khz - Part 4-2: Low voltage separation filters - Safety regulations

TS EN 60444-7 Measurement of quartz crystal unit parameters - Part 7: Measurement of quartz crystal units operation and frequency reductions

TS EN 60444-8 Measurement of quartz crystal unit parameters - Part 8: Test fixture for surface mounted quartz crystal units

TS EN 60539-2 Directly heated negative temperature coefficient thermistors - Part 2: Part feature standard - Surface mounted negative temperature coefficient thermistors

TS EN 60749-14 Semiconductor circuits - Mechanical and climatic test methods - Section 14: Robustness of terminations lead integrity

TS EN 60749-23 Semiconductor circuits - Mechanical and climate test methods - Section 23: High temperature operating life

TS EN 60749-24 Semiconductor circuits - Mechanical and climate test methods - Section 24: Accelerated moisture resistance, unbiased (ill)

TS EN 60749-25 Semiconductor circuits - Mechanical and climatic test methods - Part 25: Temperature cycle

TS EN 60825-12 Safety of laser products - Part 12: Safety of free space optical communication systems for the transmission of information

TS EN 61249-2-5 Materials and other interconnection structures for printed circuits - Part 2-5: Reinforced base materials without sheath and sheath - Flammability defined (vertical combustion test) brominant epoxide cellulose paper, self / wool e-Glass reinforced surfaces laminate leaves, copper sheathed

TS EN 60297-3-101 Mechanical structures of electronic devices - Dimensions of mechanical structures of the 482,6 mm (19 inch) series - Part 3-101: Auxiliary shelves and pluggable units

TS EN 60122-1 Quality-assessed quartz crystal units - part 1: General specification standard

TS EN 60068-2-42 Environmental resistance tests - Part 2-42: Tests - Test kc: Sulfur dioxide test for contacts and connections

Tests for environmental resistance - Part 60068-2: Tests - Test Td: Solderability of surface-mounted elements (SMD), test methods for resistance to metal coating deterioration and soldering temperature

TS EN 60286-6 Electronic circuit elements - Packaging for automatic machining - part 6: Packing box for surface-mounted circuit components

TS EN 60825-2 Safety rules - Part for laser products 2: Safety of fiber optic communication systems (fohs)

TS EN 60825-2 Safety of laser products - Part 2: Safety of fiber optic communication systems

TS EN 50065-4-2 / A2 Signals in low-voltage electrical installations-3 khz to 148,5 khz and 1,6 mhz to 30 mhz frequency range-Section 4-2: Low-voltage separation filters-Safety rules

TS EN 60747-16-4 Semiconductor circuits - Part 16-4: Microwave integrated circuits - Switches

TS EN 60747-16-10 Semiconductor circuits - Part 16-10: Technology approval scheme for single chip microwave integrated circuits (tas)

TS EN 60749-30 Semiconductor circuits - Mechanical and climatic test methods - Section 30: Pre-conditioning of non-hermetic surface-mounted circuits before reliability testing

TS EN 61747-2-2 Liquid crystal display circuits - Part 2-2: Matrix color LCD modules - Blank detail specification standard

TS EN 61747-4-1 Liquid crystal display circuits - Part 4-1: Matrix color LCD modules - Basic declaration values and specifications

TS EN 61967-2 Integrated circuits - 150 KHz - Measurement of 1 GHz electromagnetic emissions - Part 2: Measurement of airborne emissions - TEM cell and broadband TEM cell method

TS EN ISO 11807-1 "integrated optics - Terms and definitions - Part 1: Basic terms and symbols"

TS EN ISO 11807-2 "integrated optics - Terms and definitions - Part 1: Basic terms and symbols"

TS EN ISO 11146-2 Laser and laser-related equipment - Test methods for laser beam width, deflection angles and beam propagation rates - Part 2: General astigmatic beam

TS EN ISO 11146-1 Laser and laser-related equipment - Test methods for laser beam width, deflection angles and beam propagation rates - Part 1: Stigmatic and astigmatic beams

TS EN ISO 15902 Optics and photonics - Separating optics - Terms and definitions

TS EN ISO 11551 Optical and optical equipment - Laser and laser equipment - Test method for absorbance of optical laser components

TS EN 60444-1 / A1 Measurement of quartz crystal unit parameters in a network with zero phase technique - Part 1

TS EN ISO 14880-3 Optical and phonotic-microlens sequence-Section 3: Test methods for optical properties other than deviations from the lens

TS EN ISO 14880-4 Optical and phonotic-Microlens sequence-Section 4: Test methods for geometric properties

TS EN 50065-4-2 / A2 Signals in low-voltage electrical installations in the frequency range 3 khz to 148,5 khz-Section 4-2: Low-voltage separation filters-Safety rules

TS EN ISO 17526 Optical and optical instruments - Laser and laser equipment - Laser life

TS EN ISO 11146-1 Lasers and laser-related equipment - Test methods for laser beam widths, divergence angles and beam propagation rates - part 1: Stigmatic and simple astigmatic rays

TS EN 60838-2-2 Lampholders - Miscellaneous - Part- 2-2: Related specifications - Connectors for light emitting diode modules

TS EN 62384 Electronic control for direct current (da) or alternating current (aa) supply for light emitting diode (LED) modules - Performance characteristics

TS EN 60825-2 / A1 Safety rules - Part for laser products 2: Safety of fiber optic communication systems (fohs)

TS EN ISO 15902 Optics and photonics - Diffraction optics - Terms and definitions

TS EN 61189-2 Test methods for electrical materials, interconnected structures and fittings - Part 2: Test methods for materials used in interconnected structures

TS EN 62007-2 Semiconductor optoelectronic devices for fiber optic system applications - Part 2: Measurement methods

TS EN 168201 Quartz crystal units (quality approval) - Blank detail specification

TS EN 60825-12 Safety of laser products - Part 12: Safety of free space optical communication systems for the transmission of information

TS EN 60747-16-4 Semiconductor components - Part 16-4: Microwave integrated circuits - Switches

TS EN 60444-1 / A1 Measurement of quartz crystal unit parameters in a pi circuit with zero phase technique section 1: Basic method for measuring the resonance resistance and resonance frequency of quartz crystal units in a pi circuit with zero phase technique

TS EN ISO 14880-2 Optical and phonotic - Microlens array - Part 2: Test methods for wave direction deviations

TS EN ISO 11146-2 Lasers and laser-related equipment - Test methods for laser beam widths, divergence angles and beam propagation rates - part 1: General astigmatic rays

TS EN 61071 Capacitors for power electronics

TS EN 60384-4-2 Capacitors - Used in electronic equipment -Fixed- Part 4-2: Blank detail specifications- Solid (MnO2) electrolyte aluminum electrolytic capacitors- Rating level EZ

TS EN 60384-4-1 Capacitors - Used in electronic devices - Fixed - Part 4-1: Blank detail specifications - Aluminum electrolytic capacitors with non-solid electrolyte - Rating level EZ

TS EN 60444-9 Measurement of quartz crystal unit parameters - Part 9: Measurement of false resonances of piezoelectric crystal units

TS EN 61169-2 Radio-frequency connectors-Section 2: Section specification standard 9,52 type radio-frequency coaxial connectors

TS EN ISO 14880-2 Optics and photonics - Microlens array - Part 2: Test methods for wave front deflections

TS EN 61048 Auxiliary equipment for lamps - Capacitors - Used in tubular fluorescent and other discharge lamps - General and safety features

TS EN 140401-801 Detail feature: Fixed low power winding surface mounted resistors - Rectangular-shaped; Stability classes 0,1; 0,25; 0,5; 1

TS EN 61048 Auxiliary equipment for lamps - Capacitors for use in tubular fluorescent and other discharge lamps - General and safety regulations

TS EN 60194 Printed circuit board design, manufacturing and installation - Terms and definitions

TS EN 60297-3-104 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 inch) series - Part 3-104: Connector-dependent interface dimensions for lower racks and socket units

TS EN 60384-11 Stationary capacitors used in electronic equipment - Part 11: Part property standard - Capacitors in fixed polyethylene terephthalate film dielectric metal foil

TS EN 60384-11-1 Stationary capacitors used in electronic equipment - Part 11-1: Blank detail specification standard - Fixed polyethylene terephthalate film dielectric metal foil capacitors - Rating level cr

TS EN 60384-24-1 Stationary capacitors used in electronic equipment - Part 24-1: Blank detail specification standard - Surface mounted fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte - Rating level ez

TS EN 60738-1 Thermistors - Positive heating coefficient with direct heating - Part 1: General specification standard

TS EN 60738-1-2 Thermistors - Temperature coefficient with positive step function with direct heating - Part 1-2: Blank detail specification standard - Heating element application - Rating level cr

TS EN 60738-1-4 Thermistors - Temperature coefficient with positive step function with direct heating - Part 1-4: Blank detail specification standard - Detection application - Evaluation level cr

TS EN 140100 Partial features: Constant low power film resistors

TS EN 62391-2-1 Stationary electrical double layer capacitors used in electronic devices - Part 2-1: Blank detail feature - Electrical double layer capacitors for power applications - Ez rating levels

TS EN 140101-806 Detail feature: Constant low-strength film resistors - High-quality ceramic, compatible coated or molded axial or pre-formed metal film resistors

TS EN 61076-1 Qualified connectors for direct current (da), low frequency analog and digital high speed data applications - Part 1: General specifications

TS EN 61760-1 Surface-mounted technology - Part 1: Standard method for mounting technology for the properties of surface-mounted components

TS EN 61965 Mechanical safety of cathode ray tubes

TS EN 3298 Aviation series - Ferrules, thin-walled, self-locking, assembly and disassembly

TS EN ISO 11554 Optics and photonics - Lasers and equipment related to lasers - Test methods for laser beam power, energy and transient properties

TS EN 60384-20-1 Fixed capacitors used in electronic equipment - Part 20-1: Standard of empty detail specification - Fixed metallic polyethylene sulfide film dielectric surface mounted capacitors - Rating level cr

TS EN 113001 Empty detail specifications, camera tubes

TS EN 61249-4-16 Materials for printed circuit boards and other interconnection structures - Part 4-16: Part specification set for uncoated, impregnated materials (for the manufacture of multi-layer cards) - Flammability defined for lead-free devices (vertical ignition test) multifunction impregnated non-halogenated epoxy fabric e-Glass

TS EN 61249-4-15 Materials for printed circuit boards and other interconnection structures - Part 4-15: Part specification set for uncoated, impregnated materials (for the manufacture of multi-layer cards) - Flammability defined for lead-free devices (vertical ignition test) multifunction impregnated epoxy fabric E-Glass

TS EN 61249-2-37 Materials for printed circuit boards and other interconnection structures - Part 2-37: Reinforced base materials, coated and uncoated - Modified non-halogenated, flammability (vertical ignition test), epoxy fabric e-Glass sheet sheets, copper plating for lead-free fittings

TS EN 61249-2-35 Materials for printed circuit boards and other interconnection structures - Part 2-35: Reinforced base materials, coated and uncoated - Identified flammability (vertical ignition test), modified epoxy fabric e-Glass sheets, lead-free assembly for copper plating

TS EN 61076-3-114 Connectors for electronic equipment - Product rules - Part 3-114: Rectangular connectors - Use with 60603-way armored or shielded connectors for frequencies up to 7-mhz for industrial environments, including the IEC 600-8 series interface detail specifications for housings - IEC 61076-3-106-related variant 11 - Shaft coupling type

TS EN 60825-4 / A1 Safety of laser products - Part 4: Laser protectors

TS EN 60512-15-2 Connectors for electronic devices - Tests and measurements - Part 15-2: Connector tests (mechanical) - Test 15b: Retaining in the housing (axial)

TS EN 60286-5 / A1 Packaging of components for automated processes - Part 5: Matrix trays

TS EN 62341-1-2 Organic light-emitting diode screens - part 1-2: Terms and letter symbols

TS EN 61194 Characteristic parameters of grid-independent photovoltaic systems (IEC 1194: 1992, modified)

TS EN 60603-7 Connectors for electronic devices - Part 7-1: Detail specification for 8-way, unshielded free and fixed connectors

TS EN 62341-1-2 Organic light-emitting diode screens-Part 1-2: Terms and letter symbols

TS EN 60749-20 Semiconductor elements - Mechanical and climatic test methods - Section 20: Resistance of plastic encapsulated smd to the combined effect of moisture and soldering heat

TS EN 61360-1 Standard data element types and related classification plan for electrical elements - Part 1: Definitions - Principles and methods

TS EN 60603-7-41E connectors for electronic devices - Part 7-41: 8-directional, unshielded free and fixed connectors and detail specification for data transmission at frequencies up to 500 MHz

TS EN 60917-2-4 Modular layout for the development of mechanical structures in electronic hardware applications 2-4: Part specifications - Interface coordination dimensions for 25 mm hardware application - Lower shelves or cabinets according to IEC 60297-3-100 Adaptation dimensions for chassis

TS EN 60297-3-106 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 inch) series - Part 3-106: Adaptation for sub-shelves and chassis applicable to metric cabinets or shelves according to IEC 60917-2-1 dimensions

TS EN 12254 Protective screens for laser workplaces - Safety rules and tests

TS EN 62341-5 Organic light-emitting diode screens-Part 5: Environmental determination methods

TS EN 60286-2 Packaging of automatic machining components - Part 2: Packaging of components with unidirectional guides on continuously moving slivers

TS EN 62031 Led modules - For general lighting - Safety features

TS EN 60512-19-1 Electromechanical components for electronic devices - Tests and measurements - Part 19-1: Chemical resistance tests - Test 19a: Liquid resistance of pre-insulated crimp tips

TS EN 61076-2-107: 2010 Connectors for electronic equipment - Product specifications - Part 2-107: Detailed specifications for fiber optic connected round hybrid m12 connectors with screw switches

TS EN 140401-802 / A1 Detail feature - Fixed low power winding surface mounted resistors; Rectangular; Stability classes 1; 2

TS EN 140401-803 / A1 Detail feature - Fixed low power winding surface mounted resistors; Cylindrical; Stability classes 0,05; 0,1; 0,25; 0,5; 1,2

TS EN 60603-7-3 Connectors for electronic devices - Part 7-3: 8-path, shielded free and fixed connectors and detail specification for data transmission at frequencies up to 100 mhz

TS EN ISO 14881 Integrated optical-interface-connection parameters

TS EN 60603-7-5 Connectors for electronic devices - Part 7-5: 8-path, shielded free and fixed connectors and detail specification for data transmission at frequencies up to 250 mhz

TS EN 60825-2 / A2: 2010 Safety rules - Part for laser products 2: Safety of fiber optic communication systems (FOHs)

TS EN 60191-6-21 Mechanical standardization of semiconductor devices - Part 6-1: General rules for the preparation of sketches of packages for surface mounted semiconductor devices -Measuring methods for the dimensions of small draft packages (kta)

TS EN 60384-26-1 Capacitors-Fixed section used in electronic devices 26-1: Empty detail characteristics: Constant aluminum electrolytic capacitors with conductive polymer solid electrolyte-Ez limit evaluation

TS EN 60384-26 Capacitors - Fixed section used in electronic devices 26-1: Blank detail characteristics: Constant aluminum electrolytic capacitors with conductive polymer solid electrolyte

TS EN 140401: 2009 Blank detail feature: Fixed low-power winding surface mounted resistors

TS EN 61076-3-001 Connectors for electronic devices - Product specifications - Part 3- 001: Rectangular connectors - Blank detail specifications

TS EN 60512-20-3 Connectors for electronic devices - Tests and measurements - Part 20-3: Fire hazard tests-Test 20c: Flammability, glow wire

TS EN 60512-21-1 Connectors for electronic devices - Tests and measurements - Part 21-1: Rfresistance tests-Test 21a: Rf shunt resistance

TS EN 60512-22-1 Connectors for electronic devices - Tests and measurements - Part 22-1: Capacitance tests-Test 22a: Capacitance

TS EN 60603-7-7: 2010 Connectors for electronic devices - Part 7-7: 600 Detail specification for 8 directional, shielded, free and fixed connectors used for data transmission with frequencies up to Mhz

TS EN 62258-1 Semiconductor membrane products - Part 1: Terms of use and supply

TS EN 61076-3-118 Connectors for electronic equipment - Product specifications - Part 3-118: Rectangular connectors - Detailed specification for 4 pole + pe power connector with push-pull connection "

TS EN 60749-19 / A1 Semiconductor components - Mechanical and climatic test methods - Part 19: Chip breaking strength

TS EN 61975 High voltage direct current installation - System tests

TS EN 60512-8-1 Connectors for electronic devices - Tests and measurements - Part 8-1: Static load tests (fixed connectors) - Test 8a: Static load, transverse

TS EN 60512-17-0 Connectors for electronic devices - Tests and measurements - Part 17-3: Cable clamp tests- Test 17c: Cable clamp resistance to cable pull

TS EN 60512-17-1 Connectors for electronic devices - Tests and measurements - Part 17-1: Cable clamp tests- Test 17a: Cable clamp strength

TS EN 60512-17-4 Connectors for electronic devices - Tests and measurements - Part 17-4: Cable clamp tests- Test 17d: Cable clamp resistance to cable torsion

TS EN 62418 Semiconductor devices - Tensile strength test of metal properties 12.01.2011 31.080.01

TS EN 61076-3-115 Connectors for electronic equipment - Product specifications - Section 3-115: Rectangular connectors - For use with shielded or shielded 60603-way armored connectors for frequencies up to 7-mhz for industrial environments, including IEC 600-8 series interfaces Detail specifications related to housings-IEC 61076-3-106 variation associated with 12-Push-Pull type

TS EN 60747-16-4 / A1 Semiconductor components - Part 16-4: Microwave integrated circuits - Switches

TS EN 60947-1: 2007 / A1: 2011 Low-voltage switchgear and controlgear - Part 1: General rules

TS EN 62374-1 Semiconductor devices - Part 1: Time-dependent dielectric breakage for door dielectric films (tddb)

TS EN 60825-1 Safety of laser products - Part 1: Hardware classification and rules (IEC 60825-1: 2014)

60252-1: 2011 Capacitors - Part for AC motors 1: General; Performance, tests and declaration values-Safety rules-Guide for installation and operation

60252-2: 2011 Aa motor capacitors - Part 2: Motor starting capacitors

TS EN 61169-18 Radio frequency connectors - Part 18: Part feature standard - Type ssma's radio-frequency uniaxial connectors

TS EN 61984 Connectors - Safety rules and tests

TS EN 61984 Connectors - Safety requirements and tests (IEC 61984: 2008)

TS EN 60749-30 / A1 Semiconductor components - Mechanical and climatic test methods - Part 30: Preconditioning of non-sealed surface-mounted components prior to reliability testing

TS EN 60252-1 Capacitors - for AA motors - part 1: General; Performance, tests and declaration values - safety regulations - Guidelines for installation and operation

TS EN 60252-2 Capacitors - for AA motors - Part 2: Motor starting capacitors

TS EN 62047-8 Semiconductor circuits - Micro electromechanical devices - Part 8: Strip bending test method for measuring the elongation property of thin films

TS EN 60749-15 Semiconductor elements - Mechanical and climatic test methods - Part 15: Resistance to brazing temperature for hole-mounted elements

TS EN 60749-15: 2010 / AC Semiconductor elements - Mechanical and climatic test methods - Part 15: Resistance to brazing temperature for hole-mounted elements

TS EN 60194 Printed circuit board design, manufacturing and installation - Terms and definitions

TS EN 60825-4: 2006 / A2 Safety of laser products - Part 4: Laser protectors

TS EN 60825-4 / A1 Safety of laser products - Part 4: Laser protectors

TS EN 140401-804 Detail specification standard - Smd resistors fixed on a fixed low-power wire - Rectangular - Stability classes 0,1; 0,25

TS EN 60512-8-3 Connectors for electronic devices - Tests and measurements - Part 8-3: Static load tests (fixed connectors) - Test 8c: Robust arm of the mechanism "

TS EN 60512-9-3 Connectors for electronic equipment - Tests and measurements - Part 9-3: Strength tests - Test 9c: Mechanical operation in electrical load (coupling / disconnecting)

TS EN 61076-2 Connectors for electronic devices - Finished goods - Part 2: Part specifications for circular connectors

TS EN ISO 21254-1 Lasers and equipment related to lasers-Determination of laser damage threshold-Part 1: Definitions and general principles

TS EN ISO 21254-2 Lasers and equipment related to lasers-Determination of laser damage threshold-Part 2: Determination of threshold

TS EN 62258-2 Semiconductor membrane products - Part 2: Data interchange formats

TS EN 60749-21 Semiconductor components - Mechanical and climatic test methods - Part 21: Solderability

TS EN 60749-29 Semiconductor elements - Mechanical and climatic test methods - Part 29: Lockout test

TS EN 61076-2-106 Connectors for electronic devices - Product specifications - Part 2-106: Circular connectors - Detail specifications for m16x0,75 and ip40 or ip65 / 67 protection grade connectors with screw locking

TS EN 61747-5-2 Liquid crystal display devices - Part 5-2: Environmental requirements, durability and mechanical testing methods - Visual inspection of active matrix color liquid crystal display modules

TS EN 61747-6-2 Liquid crystal display devices - Part 6-2: Measuring methods of liquid crystal display modules - Reflective type

TS EN 62047-5 Semiconductor circuits - Micro-electromechanical devices - Part 5: RF MEMS switches

TS EN 62047-7 Semiconductor circuits - Micro electromechanical devices - Part 7: Radio frequency control and mems baw filter for selection

TS EN 62047-9 Semiconductor circuits - Micro-electromechanical devices - Part 9: Measurement of plate-to-plate bond strength for Mems

TS EN 60191-6-12 Mechanical standardization of semiconductor devices - Part 6-12: General guidelines for the preparation of surface-mounted semiconductor device packages - Design guide for regular spacing grid design (FLGA)

TS EN 61076-2-001 Connectors for electronic devices - Product specifications - Part 2-001: Circular connectors; Blank detail feature

TS EN 61709 Electronic components - Reliability - Reference conditions for failures and tension patterns for replacement

TS EN 61988-1 Plasma displays - Part 1: Terminology and letter symbols

TS EN 60684-2 Flexible insulating sleeve - Part 2: Test methods

TS EN 60749-40 Semiconductor devices - Mechanical and air conditioning test methods - Part 40: Test method of plate boundary drop using stain device

TS EN 61747-6-3 Liquid crystal and solid state indicator circuits - Part 6-3: Measurement methods for liquid crystal modules - Measurement of manual movement of active matrix liquid crystal display modules

TS EN 61987-10 / AC Industrial process measurements and control - Data structures and elements in the process hardware catalogs - Part 10: List of specifications for industrial process measurements and control for electronic data exchange (lop) - Basic rules

TS EN 62047-10 Semiconductor circuits - Microelectromechanical devices - Part 10: Measurement of elongation property of thin films for Mems materials

TS EN 60115-1 Stationary resistors for electronic devices - part 1: General features

TS EN 60603-7 / tst A1 Connectors for electronic devices - Part 7: Detail specifications for 8-way, unshielded, free and fixed connectors

TS EN 62047-12 Semiconductor circuits - Micro electromechanical devices - Part 12: Bending fatigue test methods of thin film materials using resonance vibration of Mems structures

TS EN 61988-2-4 Plasma screens - Part 2-3: Measurement methods - Image quality: Reflection

TS EN 61967-8 Integrated circuits - Measurement of electromagnetic emissions - Part 8: Measurement of irradiated transmissions - IC strip method

TS EN 61587-2 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 standards - Part 2: Seismic tests for cabinets and shelves

tst EN 60512-26-100Connectors for electrical equipment - Tests and measurements - Part 26-100: Creation of measurements for binders conforming to IEC 60603-7, test and reference adjustments and measurements -26a to 26g tests

TS EN 60512-26-100 / tstA1 Connectors for electrical equipment - Tests and measurements - Part 26-100: Creation of measurements for Iec 60603-7, test and reference adjustments and measurements - 26a to 26a

TS EN 60512-7-2 Connectors for electronic equipment - Tests and measurements - Part 7-2: Impact tests (free connectors) - Test 7b: Mechanical strength impact

TS EN 60512-9-2 Connectors for electronic equipment - Tests and measurements - Part 9-2: Strength tests - Test 9b: Electrical load and temperature

TS EN 60512-27-100 Connectors for electronic equipment - Tests and measurements - Part 27-100: Signal integrity tests up to 500 mhz on Iec series connectors - 27a to 27g tests

TS EN 62595-1-2 LCD backlight unit - Part 1-2: Terminolji and letter symbols

TS EN 62604-2 Surface acoustic wave (SAW) and stacked acoustic wave (BAW) pairs

TS EN 61190-1-3 / A1 Connection materials for electronic assembly - Part 1-3: Requirements for flux and flux solid soldering for electronic components and solder alloys suitable for electronic components

TS EN 62490-1 ESL measuring method - Part 1: Capacitors with polar terminals for use in electronic equipment

TS EN 62490-2 ESL measuring method - Part 2: Surface-mounted capacitors intended for use in electronic equipment

TS EN 60143-4 Series capacitors - For power systems - Part 4: Thyristor controlled series capacitors

TS EN 60749-34 Semiconductor components - Mechanical and climatic test methods - Part 34: Power cycling

TS EN 60122-3 Quality-rated quartz crystal units - part 3: Standard main dimensions and leg connections

TS EN 60368-3 Piezoelectric filters with quality assessment - Part 3: Standard main dimensions and leg connections

TS EN 60539-2 / A1 Directly heated thermistors with negative temperature coefficient - Part 2: Part specifications - Surface mounted thermistors with negative temperature coefficient

TS EN 61969-1Electrical structures of electronic devices - External enclosures - Part 1: Design guidelines

TS EN 61969-2 Mechanical structures of electronic devices - External enclosures - Part 2: Partial feature - Dimensions for sheaths and cabinets

TS EN 61969-3: 2012 (EN) for electronic equipment - Mechanical structures - Outdoor enclosures - Part 3: Part feature standard, safety conditions for cabins and chassis, climatic mechanical tests

TS EN 60384-2 Stationary capacitors for electronic devices - Part 2: Part features: Constant, metal coated polyethylene terephthalate film dielectric direct current capacitors

TS EN 60384-13 Stationary capacitors for electronic devices - Part 13: Part features - Direct current (da) capacitors with fixed, metal sheet polypropylene film dielectric

TS EN 61587-1 Mechanical structures for electronic devices - Tests for IEC 60917 and IEC 60297 - Part 1: Climatic tests for cabinets, shelves, sub-shelves and chassis, mechanical tests and safety considerations

TS EN 60384-21 Stationary capacitors for electronic devices - Part 21: Part feature standard: Class 1 ceramic dielectric fixed surface mounted multilayer capacitors

TS EN 60384-22 Stationary capacitors for electronic devices - Part 22: Part feature standard: Class 2 ceramic dielectric fixed surface mounted multilayer capacitors

61988-2-1: 2012 Plasma screens - Part 2-1: Measurement methods - Optical

TS EN 60512-1-100 Connectors for electronic devices - Tests and measurements - Part 1-100: General - Applicable standards

TS EN 60352-5 Solderless joints - Part 5: Printed joints - General rules, test methods and practical guide

TS EN 60747-15 Single semiconductor elements - Part 15: Isolated semiconductor power elements

TS EN 60115-1 Constant resistances for electronic devices - Part 1: General specifications

TS EN 62341-6-2 Organic light emitting diode (oled) screens - Part 6-2: Methods for measuring visual quality and ambient performance

TS EN 60603-7 / A1 Connectors for electronic devices - Part 7: Detail specifications for 8-way, unshielded, free and fixed connectors

TS EN 62047-13: 2012 (EN) Semiconductor elements - Microelectromechanical elements - Part 13: Bending and breaking type test methods for measuring adhesion strength for Mems structures

TS EN 62047-14 Semiconductor elements - Microelectromechanical elements - Part 14: Determination of the boundary measurement method of metallic film materials

TS EN 60297-3-107 Mechanical structures for electronic equipment - Dimensions of the 482,6 mm (19 in) series mechanical structures - Part 3- 107: Dimensions of the subframe and plug unit, small shape factor

TS EN 61727 Photovoltaic (PV) systems - Mains interface characteristics (IEC 61727: 1995)

TS EN 60301 Preferred leg diameters for wire leg resistors and capacitors

TS EN 60512-99-001 Connectors for electronic equipment - Tests and measurements - Part 99-001: Test program for insertion and removal of connectors under electrical load - Test 99a: Connectors used in remote twisted pair communication cabling

TS EN 60917-2-5 Modular sequencing for the development of mechanical structures for electronic hardware applications - Part 2-5: Part features - Interface coordination dimensions for 25 mm hardware application - Cab interface dimensions for various hardware

TS EN 61587-4 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 4: Combining performance levels for modular cabins

TS EN 60294 Dimension measurements of cylindrical components with axial termination

TS EN 61954 Static VAR (reactive power) compensators (SVC) - Tests for thyristor valves

tst ISO / IEC 10373-2 Identification cards - Test methods - Part 2: Magnetic stripe cards

TS EN 50065-4-5 Signaling in the 3 kHz to 148,5 kHz frequency range for low voltage electrical installations - Part 4-5: Low-voltage decoupling filter - Disconnect filter

tst EN 61169-2 Radio-frequency connectors-Section 2: Section specification standard Radio-frequency coaxial connectors of type 9,52 (ic 61169-2: 2001)

TS EN 60191-6-12 Mechanical standardization of semiconductor devices-Part 6-12: General rules for the preparation of drawings of surface-mounted semiconductor device packages-Design guide for regular spaced grid layout (FLGA)

TS EN 60862-2 Qualified surface acoustic wave filters: Section 2: User Manual

TS EN 61076-2-101 Connectors for electronic devices - Part 2-101: Circular connectors - Detail specification standard for snap-locking m12 or screw-locking circular m8 connectors for low voltage applications

TS EN 50581 Technical documentation for the inspection of electrical and electronic products to be kept away from explosive atmospheres

TS EN 61837-1 Surface-coated electric devices for frequency control and selection - Standard drafts and front-end connections - Part 1: Plastic cast coating dies

TS EN 61747-4 Liquid crystal display circuits -Chapter 4: Liquid crystal display units and cells-Necessary characteristics and evaluations

TS EN 61881-2 Railway applications - Railway vehicles - Capacitors for power electronics - Section 2: non-solid electrolyte aluminum electrolytic capacitors

TS EN 61881-3 Railway applications - Railway vehicles - Capacitors for power electronics - Section 3: double layer electrical capacitors

TS EN 61747-30-1 Liquid crystal display devices - Part 30-1: Measurement methods for liquid crystal display modules-transmissive type

TS EN 60512-24-1 Connectors for electronic devices - Tests and measurements - Part 24-1: Magnetic interference test-Test 24a: Residual magnetism

TS EN 60749-27 / A1 Semiconductor devices - Mechanical and climate test methods - Part 27: Electrostatic discharge (esd) sensitivity test - Machine model (mm)

TS EN 60115-8 Stationary resistors for electronic devices - Part 8: Part specification standard - Fixed surface mounting resistors

TS EN 62341-6-3 Organic light-emitting diode screens - Part 6-3: Methods for measuring image quality

TS EN 62132-8 Integrated circuits - Electromagnetic immunity measurements - Part 8: Irradiated immunity measurements-IC stripline method

TS EN 62575-2 Radio frequency (RF) acoustic wave filters (BAW) quality assessment - Part 2: User manual

TS EN 60512-16-21 Connectors for electronic devices - Tests and measurements - Part 16-21: Mechanical tests on contacts and terminations - Test 16u: Whisker test with external mechanical stress application

TS EN 61076-4-116 Connectors for electronic devices - Product specification - Part 4-116: Printed circuit connectors - Detail specifications for high-speed two-piece connection with integrated protection function

TS EN 62474 Declaration of materials used and produced in the electrotechnical industry

TS EN ISO 11553-3 Safety on machines - Laser processing machines - Part 3: Noise reduction and noise measurement methods on laser equipment and hand held laser processing machines (setting degree 2)

TS EN 60717 Method for determining the required area of capacitors and resistors with one-way terminations

TS EN 61249-2-27 Materials for printed circuit boards and other interconnection structures - Part 2-27: Coated or uncoated reinforced base materials - Bismelamide modified with non-halogenated epoxy glass fabric laminate with defined flammability (vertical ignition test) / triazine, copper plated

TS EN 61249-2-30 Materials for printed circuit boards and other interconnection structures - Part 2-30: Base materials coated or uncoated reinforced - Non halogenated epoxy modified with cyanate ester glass fabric laminate layer of defined flammability (vertical ignition test) , copper coated

TS EN 61249-2-39 Materials for printed circuit boards and other interconnection structures - Part 2-39: Coated or uncoated reinforced base materials - High performance epoxy and epoxy non-epoxy laminate with high performance defined layer, copper clad for legless installation

TS EN 61249-2-40 Materials for printed circuit boards and other interconnection structures - Part 2-40: Base materials coated or uncoated reinforced - High performance non-halogenated epoxy, E-glass fabric laminate with defined flameability (vertical ignition test) layer, copper clad for legless installation

TS EN 60512-28-100 Connectors for electronic equipment - Tests and measurements - Part 28-100: IEC 60603-7 and IEC 61076-3 series with connectors up to 1000 MHz signal integrity tests - 28a and 28g tests

TS EN 61169-26 Radio frequency connectors - Part 26: Part standard for RF coaxial connectors of the TNCA series

TS EN 61193-3 Quality assessment systems - Part 3: Selection and use of sampling plans for inspection of printed circuit board and laminate end product and process

TS EN 61587-3 Mechanical structures for electronic devices - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic screening performance tests for cabins, roofs and drawers

TS EN 62031 / A1 Led modules - For general lighting - Safety-related features

TS EN 62595-2 LCD Feedback light units - LED feedback Electro optic measurement methods

TS EN 60358-1 Connection capacitors and capacitor dividers-Section 1: General rules

TS EN 60440 Method of measuring non-linearity in resistors

TS EN 61360-2 Standard data element types with corresponding classification order for electrical components - Part 2: Schematic diagram

TS EN 61988-2-5 Plasma screens-Section 2-5: Measurement methods-Acoustic noise

TS EN 60512-9-4 Connectors for electronic equipment - Tests and measurements - Part 9-4: Strength tests - Test 9d: Endurance of connection holding system and gaskets (maintenance, aging)

TS EN 60191-6-22 Mechanical standardization of semiconductor elements - Part 6-22: General rules for the preparation of outline drawings of surface-mounted semiconductor element packages -Silicon Thin-step Top Grid Array and Silicon Thin-step Islet Grid Array Design for Silicon Thin Step Islet Grid Array Semiconductor Packages manual (S-FBGA and S-FLGA)

TS EN 60747-5-5 Individual semiconductor devices and integrated circuits-Part 5-3: Optoelectronic devices-Photocouplers

TS EN 61182-2-2 Definition data production and transfer method - Printed Panel Mounting Products Part 2-2: Printed Panel Manufacturing Data Definition for the Implementation of Regional Requirements

TS EN 61988-2-2 Plasma displays - Part 2-2: Measurement methods - Optoelectronics

60068-2-58 Tests for environmental resistance - Section 2-58: Tests - Test TD: Solderability of surface mounting elements (forging) Test methods for resistance to metallic properties and soldering temperature

TS EN 61587-1 Mechanical structures for electronic devices - Tests for IEC 60917 and IEC 60297 standard series - Part 1: Environmental requirements for cabinets, shelves, sub-shelves and chassis under indoor conditions, test setup and safety considerations

TS EN 31010 Risk Management - Risk assessment techniques (IEC / ISO 31010: 2009)

60252-2: 2011 Aa motor capacitors - Part 2: Motor starting capacitors

62629-22-1: Image elements 2013 3D - Part 22-1: Measurement methods for autostereoscopic displays - Optical

TS EN 61747-2-1 Liquid crystal display devices - Part 2-1: Passive matrix monochrome LCD modules - Blank detail feature

TS EN 60143-2 Series capacitors - for power systems - Part 2: Protective equipment for series capacitor batteries

TS EN 60679-3 Liquid crystal controlled oscillators - Quality assured - Part 3: Standard outlines and leg connections

TS EN 62595-1-1 LCD backlight unit-Section 1-1: General features

Marking of electrical and electronic equipment according to TS EN 50419 2002 / 96 / ec directive (weee) article 11 (2)

TS EN ISO 11252 Lasers and laser-related equipment - Laser element - Minimum requirements for documentation

TS EN 61643-311 Components for low-voltage shock protection devices - Part 312: Selection and application rules for gas discharge cylinders

TS EN 61643-312 Components for low-voltage shock protection devices - Part 311: Specification for gas discharge tubes

TS EN 62341-5-2 Organic light emitting diode screens - Part 5 - 2: Mechanical strength test methods

TS EN 60358-2 Connection capacitor and capacitor dividers - Part - 2: AA or DA, Single-phase, grid-frequency, connected between ground and phase, connection capacitor (PLC) application

TS EN 60252-2 / A1 Capacitors - for AA motors - Part 2: Motor starting capacitors

TS EN 62341-5-3 Organic light-emitting diode screens - Part 5 - 3: Test methods for life and image retention

TS EN 60252-1 / A1 Capacitors - for AA motors - part 1: General; Performance, tests and declaration values - safety regulations - Guidelines for installation and operation

Tests for resistance to environmental conditions - Section 60068-2: Tests - Test Tee: Solderability of electronic components for surface-mounted elements (SMD) by soldering stability method

TS EN 60286-3 Packaging of components for automatic machining section 3: Packaging of elements placed on the surface on continuously moving strips

TS EN 60384-14 Stationary capacitors for electronic devices - Part 14: Part features - Stationary capacitors for electromagnetic interference suppression and connected to the supply network

TS EN 61191-1 Printed circuit installations - Part 1: General standard - Requirements for soldered electrical and electronic installations using surface-mounted and related installation technologies

62629-1-2 Image elements - Section 3-1 General - Terms and letter symbols

TS EN 62739-1 Test method for erosion in corrugated soldering equipment using molten lead-free solder alloy - Part 1: Erosion test method for non-surface treated metal materials

TS EN 60352-2 / A1 Solderless connections - Part 2: Solderless fixed connections - General rules, test methods and application guide

TS EN 60747-16-5 Semiconductor components - Part 16-5: Microwave integrated circuits - Oscillators

TS EN 61954 / A1 Static VAR compensators (SVC) -Tristor valve tests

TS EN 62047-11 Semiconductor elements - Micro-electromechanical elements - Part 11: Test method for linear thermal expansion coefficients of free-standing materials for micro-electromechanical systems

TS EN 62047-18 Semiconductor elements - Micro-electromechanical elements - Part 18: Bending test methods of thin film materials

TS EN 62047-19 Semiconductor components - Micro-electromechanical elements - Part 19: Electronic compasses

TS EN 60444-6 Measurement of quartz crystal unit parameters-Section 6: Measurement of drive level dependency (ssb)

TS EN 61191-2 Printed circuit units - Part 2: Part feature: Requirements for the surface mounted on soldered units

TS EN 61747-10-1 Liquid crystal display devices - Part 10-1: Environmental requirements, durability and mechanical test methods -Mechanical

TS EN 62215-3 Integrated circuits - Measurement of impulse immunity - Part 3: Asynchronous transient injection method

TS EN 60286-3 / AC Packaging of components for automatic machining part 3: Packaging of elements placed on the surface on continuously moving strips

TS EN 60286-4 Electronic circuit elements - Packaging for automatic processing - Part 4: Adhesive cartridges for electronic elements packed in E and g

TS EN 62610-4 Mechanical structures for electronic equipment - Temperature management for cabinets according to IEC 60297 and IEC 60917 series - Part 4: Cooling performance tests for water-fed heat exchangers in electronic cabinets

TS EN 140101-806 / A1 Detail feature: Constant low-strength film resistors - High-quality ceramic, compatible coated or molded axial or pre-made metal film resistors

TS EN 140401-801 / A1 Detail feature: Fixed low-power winding surface mounted resistors - Rectangular-shaped; Stability classes 0,1; 0,25; 0,5; 1

TS EN 140401-802 / A2Detail feature-Fixed low-power winding surface mounted resistors; Rectangular; Stability classes 1; 2

TS EN 140401-804 / A1Detay specification standard - Smd resistors fixed on fixed low-strength wire - Rectangular - Stability classes 0,1; 0,25

TS EN 61249-4-18 Materials for printed circuit boards and other interconnection structures - Part 4-18: Part standard set for resin impregnated materials, uncoated (for the manufacture of multi-layer cards) - Flammability defined for lead-free installation (vertical combustion)

TS EN 61249-4-19 Materials for printed circuit boards and other interconnection structures - Part 4-19: Part standard set for resin impregnated materials, uncoated (for the manufacture of multi-layer cards) - Flammability defined for lead-free installation (vertical side)

TS EN 60191-3 Mechanical standardization of semiconductor elements - part 3: General rules for the preparation of outline drawings of integrated circuits

TS EN 60512-12-6 For electronic devices - Electromechanical components - Basic test procedures and measuring methods - Part 12: Soldering tests - Part 6: Test 12f: Sealing against paste and cleaning solvents and solder paste in machine soldering

TS EN 100012 X-ray examination of electronic materials - Key features

TS EN 50625-1 Collection, logistics and processing requirements for WEEE - Part 1: General Processing Requirements

TS EN 62146-1 Leveling capacitors for high voltage alternating current circuit breakers

TS EN 61587-5 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 5: Seismic tests for chassis, sub-shelves and plug units

TS EN 60512-12-7 Fasteners for electronic equipment - Tests and measurements - Part 12-7: Soldering tests - Test 12g: Solderability - Solder holding stability method

TS EN 60191-4 Mechanical standardization for semiconductor element packages - Part 4: Classification of package main dimensions for semiconductor elements according to models and coding system

TS EN 61954 / A1 Static VAR (reactive power) compensators (SVC) - Tests for thyristor valves (IEC 61954: 2011 / A1: 2013)

TS EN 60749-26 Semiconductor components - Mechanical and climatic test methods - Part 26: Electrostatic discharge (ESD) sensitivity tests - Human body model (HBM)

TS EN 61190-1-2 Fastening materials for electronic assembly - Part 1-2: Rules for solder paste used in high-quality interconnections in electronic assembly

TS EN 61837-2 / A1 Surface mounted piezoelectric elements for frequency control and selection - Standard outlines and terminal end connections - Part 2: Ceramic housings

TS EN 62761 Basic principles for measuring non-linearity in radio frequency (RF) surface acoustic wave (SAW) and volumetric acoustic wave (BAW) elements

TS EN 62522 Calibration of tunable laser sources

TS EN 60825-1 Safety of laser products - Part 1: Hardware classification and rules

TS EN 61076-2-109 Connectors for electronic equipment - Product rules - Part 2-109: Circular connectors - Detail standard for M12 x 1 screw-locking connectors, for data transmission frequencies up to 500 MHz

TS EN 60831-1 Self-repairing shunt power capacitors for aa systems with rated voltage up to and including 1000 V. - Part 1: General - Performance, tests and declaration characteristics - Safety regulations - Guidelines for plant and operation

TS EN 60831-2 Self-repairing shunt power capacitors for aa systems with rated voltage up to and including 1000 V - Part 2: Aging test, self-repair test and destruction test

TS EN 60871-4 Shunt capacitors for aa power systems with rated voltages higher than 1000 V. - Part 4: Internal fuses

TS EN 60871-1 Capacitors - Shunt capacitors for aa power systems with rated voltage above 1000 V. - Part 1: General

TS EN 60947-4-3 Low-voltage switching and control devices - Part 4-3: Contactors and motor starters - AA semiconductor control devices and contactors for non-motorized loads

TS EN 140101-806 / ACDetay standard: Constant low-strength film resistors - Metal film resistors with axial or pre-formed leg on high-quality ceramic, coated or molded

TS EN 140401-802 / ACDetay standard: Constant low power SMD resistors - Rectangular - Stability class 1; 2

TS EN 60947-4-3 Low-voltage switchgear and controlgear - Part 4-3: Contactors and motor starters - AA semiconductor control devices and contactors for non-motor loads

TS EN ISO 11990-1 Lasers and laser-related equipment - laser resistance determination in tracheal tubes - Part 1: Tracheal tube shaft

TS EN ISO 11990-2 Lasers and laser-related equipment - laser resistance determination of tracheal tubes - Part 2: Tracheal tube cuffs

TS EN 62047-20 Semiconductor elements - Micro-electromechanical elements - Section 20: Gyroscopes

TS EN 62047-21 Semiconductor elements - Micro-electromechanical elements - Part 21: Test method for Poisson's ratio of thin film MEMS materials

TS EN 60749-42 Semiconductor elements - Mechanical and climate test methods - Part 42: Temperature and humidity test chambers

TS EN 61076-2-104 Connectors for electronic equipment - Product rules - Part 2-104: Circular connectors - M8 detail standard for screw-locking or spring-locking circular connectors

TS EN 60352-5 / AC Solderless connections - Part 5: Compression connections - General rules, test methods and application guide

Environmental resistance tests - Section 60068-2: Tests - Experiment Ta: Solderability of electronic components by soldering balance method (IEC 54-2-54: 60068)

TS EN 60831-1 Self-repairing shunt power capacitors for aa systems with rated voltage up to 1000 V (including 1000 V) - Part 1: General - Performance, tests and declaration characteristics - Safety regulations - Guidelines for installation and operation IEC 60831-1: 2014)

TS EN 60252-1 / A1 Alternating current motor capacitors - Part 1: General - Performance, tests and declaration values - Safety regulations - Guidance on installation and use

TS EN 60252-2 / A1 Alternating current motor capacitors - Part 2: Motor starting capacitors (IEC 60252-2: 2010 / A1: 2013)

tst EN 60358-2 Connection capacitor and capacitor dividers - Part - 2: AA or DA, Single-phase, grid-frequency, connected between ground and phase, connection capacitor (PLC) application IEC 60358-2: 2013)

TS EN 60831-2 Self-repairing shunt power capacitors for aa systems with rated voltage up to 1000 V (including 1000 V) - Part 2: Aging test, self-repair test and destruction test (IEC 60831-2: 2014)

TS EN 60871-1 Shunt capacitors for aa power systems with rated voltage above 1000 V. - Part 1: General (IEC 60871-1: 2014)

TS EN 60871-4 Shunt capacitors for aa power systems with rated voltage above 1000 V. - Part 4: Internal fuses (IEC 60871-4: 2014)

tst EN 62146-1 Leveling capacitors for high voltage alternating current circuit breakers

tst EN 61643-311 Components for low-voltage shock protection devices - Part 311: Selection and application rules for gas discharge cylinders

tst EN 61643-312 Components for low-voltage shock protection devices - Part 312: Specification for gas discharge tubes

TS EN 62137-4 Electronic assembly technology - Part 4: Strength test methods of solder joints of field array type packaged surface mounted circuit elements

TS EN 50625-2-1 Collection, logistics and treatment requirements for WEEE - Part 2-1: Treatment requirements for lamps

TS EN 60297-3-108 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-108: Dimensions of R-type bottom shelves and removable units

TS EN 50065-4-7 Signals in the frequency range 3 kHz - 148,5 kHz and 1,6 MHz to 30 MHz in low voltage electrical installations - Part 4-7: Portable low-voltage decoupling filters - Safety regulations

TS IEC 60050-581 International Electrotechnical Glossary - Part 581: Electromechanical components of electronic devices

TS IEC 60050-521 International Electrotechnical Glossary - Part 521: Semiconductor elements and integrated circuits

TS EN 50419 Marking of electrical and electronic equipment in accordance with Article 2002 (96) of Directive 11 / 2 / EC (AEEE)

TS EN 50625-1 Collection, logistics and treatment requirements for WEEE - Part 1: General treatment requirements

TS EN 50625-2-1 Collection, logistics and treatment requirements for WEEE - Part 2-1: Treatment requirements for lamps

TS EN 16602-70-11: 2015 Space product assurance - Supply of printed circuit boards

TS EN 16602-70-10 Space product assurance - Characterization of printed circuits

TS EN 61587-1 / D1 Mechanical structures for electronic devices - Tests for IEC 60917 and IEC 60297 standard series - Part 1: Environmental requirements for enclosures, shelves, sub-shelves and chassis under building conditions, test setup and safety considerations

TS EN 62137-4 / AC Electronic assembly technology - Part 4: Strength test methods of solder joints of field array type packaged surface-mounted circuit elements

TS EN 62813 Lithium ion capacitors for electrical and electronic equipment - Test methods for electrical characteristics

TS EN 61189-5-2 Test methods for electrical materials, printed circuits and other interconnection structures and units - Part 5-2: General test methods for materials and units - Solder flux for printed circuit units

TS EN 61189-5-3 Test methods for electrical materials, printed circuits and other interconnection structures and units Part 5-3: General test methods for materials and units - Solder paste for printed circuit units

TS EN 61189-5-4 Test methods for electrical materials, printed circuits and other interconnection structures and units Part 5-4: General test methods for materials and units - Solder alloys for printed circuit units and solid wire with or without paste

TSE K 216Traffic monitoring systems (TEDES) - Part 1: Speed violation detection equipment (HITD) - Doppler radar based

tst EN 62595-1-2 LCD backlight unit - Part 1-2: Therminolgia and letter symbols

TS EN 50360 / tst A1 Product standard that demonstrates the suitability of mobile telephones with the basic limitations of electromagnetic fields (300 mhz-3 ghz) to which people are exposed

tst EN 50065-4-6 3 khz - Signing in low voltage electrical installations in the frequency range 148,5 khz - Part 4-6: Low voltage decoupling filters - Angle coupler

tst ISO / IEC 8825-2 Information technology - Asn.1 encryption rules: Feature (pack) related to packaged encryption rules

tst EN 50065-4-4 3 khz - Signing in low-voltage electrical installations in the frequency range 148,5 khz - Part 4-4: Low voltage decoupling filter - Impedance filter

tst EN 12016 Electromagnetic compatibility - Product family standard for elevators, escalators and conveyors - Immunity

TS EN 50625-2-2 Collection, handling and treatment requirements for Waste Electrical and Electronic Equipment - Part 2-2: Treatment requirements for Waste Electrical and Electronic Equipment including CRTs and flat panel displays

tst EN 50625-2-2 Collection, handling and treatment requirements for Waste Electrical and Electronic Equipment - Part 2-2: Treatment requirements for Waste Electrical and Electronic Equipment including CRTs and flat panel displays

50065-4-3 3 kHz to 148,5 kHz Signing of low-voltage electrical installations in the frequency range - Part 4-3: Low-voltage decoupling filter - Input filter

TS EN 60358-1 / AC Connection capacitors and capacitor dividers-Section 1: General rules

TS EN 60831-1 / AC Self-repairing shunt power capacitors for aa systems with rated voltage up to 1000 V (including 1000 V) - Part 1: General - Performance, tests and declaration characteristics - Safety requirements - For installation and operation guide

TS EN 62341-5-3 Organic light-emitting diode screens - Part 5 - 3: Test methods for life and image retention

TS EN 62341-5-2 Organic light emitting diode screens - Part 5 - 2: Mechanical strength test methods

tst EN 60601-2-22 Electrical medical devices - Part 2-22: Specific requirements for the safety of diagnostic and therapeutic laser devices (IEC 60601-2-22: 2007 + A1: 2012)

TS EN 60601-2-22 Electrical medical devices - Part 2-22: Specific features for the safety of diagnostic and therapeutic laser devices

TS EN 60143-3 Series capacitors intended for grid installation - Part 3: Internal fuses

TS EN 60143-1 Series capacitors intended for grid installation - Part 1: General

TS EN ISO 11810 Lasers and laser-related equipment - Classification and test method of laser resistance for surgical drapes and / or patient protective covers - Primary ignition, penetration, flame spread and secondary ignition

TS EN ISO 13694 Optical and optical instruments - Laser and laser-related equipment - Test methods for laser beam power (energy) density distribution

TS EN 60297-3-109 Mechanical structures for electrical and electronic equipment - Dimensions of mechanical structures of the 482,6 mm series - Part 3 - 109: Chassis dimensions for embedded computing devices

TS EN 62132-1 Integrated circuits - Measurement of electromagnetic immunity - Part 1: General requirements and definitions

TS EN 62391-1 Stationary electrical double-layer capacitors for electrical and electronic equipment Part 1: General standard

TS EN 62575-1 Quality assessed radio frequency (RF) collective acoustic wave (BAW) filters - Part 1: General standard

TS EN 60512-29-100 Connectors for electronic equipment - Tests and measurements - Part 29-100: Signal integrity tests up to 12MHz on M500 type connectors

TS EN 62604-1 Quality assessed surface acoustic wave (SAW) and collective acoustic wave (BAW) duplex - Part 1: General standard

TS EN 60384-20 Constant capacitors used in electronic devices - Part 20: Part features: Surface-mounted direct current (da) capacitors with fixed metal-coated polyphenylene sulfur film

TS EN 60384-24 Stationary capacitors used in electronic equipment - Part 24: Part specification standard - Surface mounted fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte

TS EN 60384-25 Stationary capacitors used in electronic equipment - Part 25: Part specification standard - Surface mounted fixed aluminum electrolytic capacitors with conductive polymer solid electrolyte

TS EN 60862-1 Qualified surface acoustic wave filters: Part 1: General specification standard

TS EN 60939-3 Passive filter elements for electromagnetic interference suppression - Part 3: Passive filter units for suitable safety tests

TS EN 60384-19 Stationary capacitors for use in electronic equipment - Part 19: Part specification standard: Fixed metallic polyethylene terephthalate film condensers attached to a dielectric surface

TS EN 61837-3 Surface-mounted pizoelectronic devices for frequency control and selection - Standard frames and end copper connections - Part 3: Metal coaters

TS EN 61048 / A1 Auxiliary equipment for lamps - Capacitors - Used in tubular fluorescent and other discharge lamps - General and safety features

TS 2016107880 Traffic electronic monitoring systems (TEDES) - Average speed measuring equipment (OHÖD)

TS EN ISO 11145 Optical and photonics - Lasers and laser-related equipment - Terms and symbols

TS EN 61076-4-116 / A1 Connectors for electronic devices - Product specification - Part 4-116: Printed circuit connectors - Detail specifications for high-speed two-piece connection with integrated protection function

TS EN 60384-14 / AC Stationary capacitors for electronic devices - Part 14: Part features - Stationary capacitors for electromagnetic interference suppression and connected to the supply network

TS EN 60384-14-1 Stationary capacitors used in electronic devices - Part 14-1: Blank detail feature: Stationary capacitors used in electromagnetic interference suppression and connected to the supply network - Rating level d

TS EN 60393-2 Potentiometers for electronic devices - Part 2: Part Features - Potentiometers that can be pre-adjusted by screwing and turning

TS EN 60393-5 Potentiometers for electronic devices - Part 5: Part features - Single turn rotary low-potentiometer with and without wire winding

TS EN 60393-6 Potentiometers for electronic devices - Part 6: Part features - Adjustable surface mounted potentiometers

TS EN 60603-7-81 Connectors for electronic equipment - Part 7 -81: Detail standard for 2000 bus, armored, free and fixed connectors for data transmissions with frequencies up to MHz

TS EN 60939-3 / AC Passive filter elements for electromagnetic interference suppression - Part 3: Passive filter units for suitable safety tests

TS EN 61189-3-719 Test methods for electrical materials, printed circuit boards and other interconnection structures and installations - Part 3- 719: Test methods for interconnection structures (printed cards) - Single-sided coated bore (PTH) during temperature cycle ) monitoring of resistance value change

TS EN 62047-1 Semiconductor devices - Micro-electromechanical devices - Part 1: Terms and definitions

TS EN 62047-26 Semiconductor elements - Micro electromechanical elements - Description and measurement methods for micro hollow and needle structures

TS EN 60384-14-2 Stationary capacitors for electronic devices - Part 14-2: Standard of empty specification: Fixed capacitors for electromagnetic interference suppression and connection to mains - Safety tests only

TS EN 62326-20 Printed Cards - Part 20: Printed circuit boards for high-brightness LEDs

TS EN 62779-2 Semiconductor devices - Semiconductor interfaces for human body communication - Part 2: Characterization of interface performances

TS EN ISO 11151-1 Equipment for lasers and lasers - Standard optical components - part 1: Components for UV, visible and near infrared spectral regions

TS EN ISO 11151-2 Lasers and laser-related equipment - Standard optical components - Part 2: Components for infrared spectral regions

TS EN 62572-3 Fiber optic active components and elements - Reliability standards - Part 3: Laser modules for communication

TS EN 62610-5 Mechanical structures for electrical and electronic equipment - Thermal management of cabinets according to IEC 60297 and IEC 60917 series - Cooling performance evaluation for enclosed cabinets

TS EN 62779-1 Semiconductor devices - Semiconductor interfaces for human body communication - Part 1: General rules

TS EN 62779-3 Semiconductor devices - Semiconductor interfaces for human body communication - Part 3: Functional type and operating conditions

TS EN 60195 Method for measuring current noise in fixed resistors

TS EN 60539-1 Direct heating negative temperature coefficient thermistors - Part 1: General specification standard

TS EN 61249-2-43 Materials for printed circuit boards and other interconnection structures - Part 2 - 43: Coated and uncoated reinforced basic materials - Halogenated epoxide cellulose paper / woven E-work flammability (vertical ignition test) with glass reinforced laminate sheets, lead-free installation copper plating

TS EN 61249-2-44 Materials for printed circuit boards and other interconnection structures - Part 2 - 44: Coated and uncoated reinforced basic materials - Non-halogenated epoxide nonwoven / woven E-work flammability (vertical ignition test) glass reinforced laminated sheets, lead-free copper coating

TS EN ISO 14880-1 Optics and photonics - Microlens array - Part 1: Terms, descriptions and general features

TS EN 62146-1 / A1 Leveling capacitors for high voltage alternating current circuit breakers

TS EN 16602-70-12 Space product assurance - Design rules for printed circuit boards

tst 2016114296 Electronic monitoring systems (EDS) - Speed detection equipment (HITD) - Doppler radar based

TS EN 60384-1 Constant capacitors for electronic equipment Part 1: General specifications

TS EN 60384-18 Stationary capacitors for electronic equipment Part 18: Part features - Fixed aluminum electrolytic surface mounted capacitors, solid (MnO2) and non-solid electrolyte

TS EN 60758 Synthetic quartz crystal - Specifications and instructions for use

TS EN 61189-5-1 Test methods for electrical materials, printed circuits and other interconnection structures and units - Part 5-2: General test methods for materials and units - Guidelines for printed circuit assemblies

TS EN 60062 Marking codes for resistors and capacitors

TS EN 60062 / AC Marking codes for resistors and capacitors

TS EN 60384-3 Stationary capacitors for use in electronic equipment - Part 3: Part features - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electrolyte

TS EN 60384-4 Fixed capacitors for use in electronic equipment - Part 3: Part features - Solid aluminum electrolytic capacitors with solid (MnO2) and non-solid electrolyte

TS EN 60749-44 Semiconductor elements - Mechanical and climatic test methods - Neutron beam irradiated single event effect (SEE) test method for semiconductor devices

TS EN 61189-2-719 Test methods for electrical materials, interconnected structures and assemblies - Part 2: Test methods for materials used in interconnected structures - Relative permeability and loss tangent (500 MHz between 10 MHz)

TS EN 62433-4 EMC IC modeling - Part 4: Integrated circuit models for RF immune behavior simulation - Conductive immunity modeling (ICIM-CI)

TS EN 62739-2 Test method for erosion in corrugated soldering equipment using molten lead-free solder alloy - Part 2: Erosion test method for surface treated metal materials

TS EN 60191-6-13 Mechanical standardization of semiconductor devices - Part 6-13: Design guide for regular spaced grid arrangement (FLGA) and grid arrangement of fine holes (FBGA) (FBGA / FLGA)

TS EN 61076-3-110 Connectors for electronic devices - Product specifications - Part 3-110: Detail specifications for free and fixed connectors for frequency data transmission up to 3000 MHz

TS EN 62047-25 Semiconductor devices - Micro electromechanical devices - Part 25: Silicon-based MEMS production technology - Tensile press and shear force measurement method of micro bonding area

TS EN 60384-14 / A1 Fixed capacitors for electronic devices - Part 14: Part features - Fixed capacitors for electromagnetic interference suppression and connected to the supply network

TS EN 61360-6 Standard data element types, with combined classification scheme for electrical components - Part 6: IEC Common Data Dictionary (IEC CDD) quality guidelines

TS EN 60603-7-82 Fasteners for electronic equipment - Part 7 -81: Detail standard for 2000-way, 8 contact, armored, free and fixed connectors for data transmissions with frequencies up to MHz

TS EN 61076-3-120 Connectors for electronic devices - Product specifications - Section 3-120: Rectangular connectors - Switch-disconnected, reconnected power connectors for rated voltage 250 V dc and rated current 30 A

TS EN 62276 Single crystal plates for surface acoustic wave applications - Specification and measurement methods

TS EN 62391-1 / AC Stationary electrical double-layer capacitors for electrical and electronic equipment Part 1: General standard

TS EN 140402 Blank detail specification: Fixed low-strength wire winding surface mounting resistors

TS EN 140402 / A1 Blank detail specification: Fixed low-strength wire winding surface mounting resistors

TS EN 140402-801 Detail specification standard - Fixed low-strength wire-wound surface-mounted (SMD) resistors - Rectangular - Stability classes 0,5; 1,2

TS EN 60384-24 / AC Stationary capacitors used in electronic equipment - Part 24: Part specification standard - Surface mounted fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte

TS EN 61240 Piezoelectric elements - Preparation of outline drawings of surface mounted elements (SMD) for frequency control and selection - General rules

TS EN 62031 / A2 LED modules - For general lighting - Safety-related features

TS EN 140401-802 / A3 Detail feature - Fixed low power winding surface mounted resistors; Rectangular; Stability classes 1; 2

TS EN 140401-803 / A3Detail feature-Fixed low-power winding surface mounted resistors; Cylindrical; Stability classes 0,05; 0,1; 0,25; 0,5; 1,2

TS EN 140401-803 / A2Detail feature-Fixed low-power winding surface mounted resistors; Cylindrical; Stability classes 0,05; 0,1; 0,25; 0,5; 1,2

TS EN 62435-5 Electronic components - Long-term storage of electronic semiconductor devices - Part 5: Mold and chipboard devices

TS EN 62739-3 Test method for erosion in corrugated soldering equipment using molten lead-free solder alloy - Part 3: Erosion test methods selection guide

TS EN 63002 Identification and communication interoperability method for external power supplies used with portable computing devices

TS ISO 10110-17 Optical and photonics - Preparing drawings of optical elements and systems - Part 17: Laser irradiation damage threshold

TS EN ISO 11807-2 Integrated optics - Terms and definitions - Part 2: Terms used in classification

TS EN ISO 11807-1 Integrated optics - Terms and definitions - chapter 1: Basic terms and symbols

TS 1829 EN 60097 Grating systems for printed circuits

TS 3769 EN 130200 Part features - Solid tantalum capacitors with solid and non-solid electrolyte

TS EN ISO 11551 Optical and optical instruments - Laser and laser equipment - Test method for the absorption factor of optical laser components

TS EN ISO 11553-1 Safety in machines - Laser machines - Part 1: General safety rules

TS EN ISO 11553-2 Safety in machines - Laser processing machines - Part 2: Safety requirements for hand-held laser processing machines

TS EN ISO 11670 Lasers and equipment related to lasers - Test methods for laser beam parameters - Position stability of the beam

TS EN ISO 11732 Water quality - Determination of ammonium nitrogen by flow analysis (CFA and FIA) and spectrometric detection

TS EN ISO 12005 Laser and laser-related equipment - Test methods for laser beam parameters - Polarization

TS EN ISO 13695 Optical and photonics - Laser and laser-related equipment - Test methods for the spectrum properties of lasers

TS EN ISO 13697 Optics and photonics - Laser and laser-related equipment - Test methods for uniform reflectance and regular transmission of optical laser elements

TS EN 140401-802 Detail feature-Fixed low-power winding surface mounted resistors; Rectangular; Stability classes 1; 2

TS EN ISO 14880-3 Optics and photonics - Microlens array - Part 3: Test methods for optical properties other than wavefront deflection

Optical and photonics - Microlens array - Part 14880: Test methods for geometric properties TS EN ISO 4-4

TS EN ISO 15061 Water quality-Determination of dissolved bromate-Determination of ions by liquid chromatography

TS EN ISO 15367-2 Laser and laser-related equipment - Test methods for determining the shape of a beam wave direction - Part 2: Hartmann-Shack sensors

TS EN ISO 21254-3: 2011 Lasers and equipment related to lasers-Determination of the damage threshold caused by laser-Part 3: Laser power (energy) processability safety

TS EN ISO 24013 Optics and photonics - Lasers and laser-related equipment - Measurement of phase delay of optical components for polarized laser radiation

TS EN 31010 Risk management - Risk assessment techniques

TS EN 50065-4-1 Signaling in the 3 khz to 148,5 khz frequency range in low voltage electrical installations - Part 4-1: Low voltage separation filters - General specification standard

TS EN 50065-4-4 3 khz - Signing in low voltage electrical installations in the frequency range 148,5 khz - Part 4-4: Low voltage decoupling filter - Impedance filter

TS EN 50065-4-5 3 khz - Signing in low-voltage electrical installations in the frequency range 148,5 khz - Part 4-5: Low-voltage decoupling filter - Separation filter

TS EN 50065-4-6 3 khz - Signing in the low voltage electrical installation in the frequency range 148,5 khz - Part 4-6: Low voltage decoupling filters - Angle coupler

Signs in low voltage electrical installations in the frequency range 50065 kHz to 4 kHz - Part 3-3: intended for use in industrial environments and for systems operating in the 148,5 kHz - 2 kHz frequency range

TS EN 50324-1 Piezoelectric properties of ceramic materials and components-Part 1: Terms and definitions

TS EN 50324-2 Piezoelectric properties of ceramic materials and components-Part 2: Measurement methods low power

TS EN 50324-3 Piezoelectric properties of ceramic materials and components-Part 3: Measurement methods-High power

TS EN 50528 Insulating gloves for use on or near low voltage installations

TS EN 62430 Conscious design of environmental conditions for electrical and electronic products

TS EN 60027-2 Letter symbols used in electrical technology section 2: Communication and electronics

Environmental resistance test - Section 60068-2: Tests - Kd test: Hydrogen sulfide test for contacts and connections

Test of environment - Part 60068-2: Tests - Experiment: Solderability test of electronic elements by means of wet balance method

The test of the solderability of electronic components for surface-mounted elements (smd) by means of the soaking equilibrium method - TS EN 60068-2-69

Environmental testing - Section 60068-2-Tests - Tx test: whisker test methods for electrical and electronic components

TS EN 60115-9 Stationary resistors used in electronic devices - Part 9: Part feature standard: Resistor circuits mounted on a fixed surface with individually measurable resistor

TS EN 60115-9-1 Stationary resistors used in electronic devices - Part 9-1: Standard of empty detail specification: Resistive circuits mounted on fixed surface with individually measurable resistance - Ez rating level

TS EN 60130-17 Connectors for frequencies below 3 mhz - Part 17: Detail specifications for the versatile interlocking devices used in rechargable batteries allowing interlocking

TS EN 60130-9: 2011 3 connectors for sub-frequencies - Part 9: Circular connectors for radio and audio equipment

TS EN 60191-6-6 Mechanical standardization of semiconductor elements - Part 6-6: General guidelines for the preparation of outline drawings of surface-mounted semiconductor element packages - Design guide for regularly spaced grid array (flga)

TS EN 60191-1 Mechanical standardization of semiconductor elements - Part 1: General rules for the preparation of outline drawings of discrete elements

TS EN 60191-6 Mechanical standardization of semiconductor devices - Part 6: General rules for the preparation of outline drawings of surface-mounted semiconductor circuit packages

TS EN 60191-6-19 Mechanical standardization of semiconductor devices - Part 6-19: Measurement methods of package warpage at high temperatures and maximum permissible warpage

TS EN 60191-6-20: Mechanical standardization of semiconductor devices - Part 2010-6: General rules for the preparation of sketches of packages for surface-mounted semiconductor devices - Measurement methods for the dimensions of small draft j-pin packages (ktj)

TS EN 60191-6-17: 2011 Mechanical standardization of semiconductor devices - Part 6-17: General rules for the preparation of draft drawings of packages for surface-mounted semiconductor design guidelines for stacked packages - Design guide for regular spacing and regular spacing grid layout ppfbga and p-Pflga)

TS EN 60191-6-10 Mechanical standardization of semiconductor circuits - Part 6-10: General rules for the preparation of master plan drawings of surface mounted semiconductor circuits - Measurement methods for P-Vson measurements

TS EN 60191-6-16 Mechanical standardization of semiconductor elements - Part 6-16: Glossary of practice sockets and semiconductor tests for bga, lga, fbga and flga

TS EN 60191-6-18 Mechanical standardization of semiconductor devices - Part 6-18: General rules for preparing outline drawings of the surface mount of semiconductor device packages - Design guide for the round grid array

TS EN 60268-12 Sound system devices - Part 12: Connector applications for broadcasting and similar purposes

TS EN 60286-1 Electronic circuit elements - Packaging for automatic machining - Part 1: Strip packaging of elements with wires in axial direction on continuously moving strips

TS EN 60286-5 Packaging of components for automated processes - part 5: Matrix trays

TS EN 60286-5 / A1 Packaging of components for automated processes - part 5: Matrix trays

TS EN 60297-3-103 Mechanical structures of electronic devices - Dimensions of mechanical structures of the 482,6 mm (19 inch) series - Part 3-103: Switching and alignment adjustment pin

TS EN 60297-3-105 Mechanical structures for electronic devices - Dimensions of the 482,6 mm (19 in) series mechanical structures - Part 3-105: Dimensions and design conditions for 1 chassis

TS EN 60297-3-100 Mechanical structures for electronic devices - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of the front panels, bottom shelves, chassis, racks and cabinets

TS EN 60297-3-102 Mechanical structures of electronic devices - Dimensions of mechanical structures of the 482,6 mm (19 inch) series - Part 3-102: Injector / extractor handle

TS EN 60297-3-101 Mechanical structures for electronic equipment - 482,6 mm (19 inch) series mechanical construction dimensions - Part 3-101: Lower shelves and combined plug-in units - Electrostatic discharge protection

TS EN 60300-3-1 (Formerly: TS IEC 60300-3-1) Reliability management - Part 3-1: Application guide - Analysis techniques for reliability - Methodology guide

TS EN 60368-1 Piezoelectric filters with quality assessment - part 1: General features

TS EN 60368-4 Quality-assessed piezoelectric filters section 4: Section feature - Capability approval

TS EN 60368-2-2 Quality-assessed piezoelectric filters - Part 2: Instruction manual for piezoelectric filters - Part 2: Piezoelectric ceramic filters

TS EN 60384-21-1 Stationary capacitors used in electronic devices - Part 21-1: Empty detail specification standard: Class 1, multi-layer capacitors mounted on fixed surface of ceramic dielectric type - Ez rating

TS EN 60384-23 Stationary capacitors for electronic devices - Part 23: Part feature standard: Metallic polyethylene naphthalate film dielectric condensers in fixed surfaces

TS EN 60384-9-1 Stationary capacitors used in electronic devices - Part 9-1: Empty detail specification standard: Class 2 ceramic dielectric fixed capacitors ez rating level

TS EN 60384-22-1 Stationary capacitors for use in electronic equipment - Part 22-1: Standard of empty detail specification: Class 2, multi-layer capacitors fitted on a ceramic dielectric fixed surface - Ez rating

TS EN 60384-3-1 Capacitors - Fixed section used in electronic devices 3-1: Empty detail characteristics: Fixed, tantalum broken (chip) capacitors rating level e.

TS EN 60384-8 Stationary capacitors used in electronic devices - section 8: Section characteristics: Ceramic dielectric stationary capacitors, class 1

TS EN 60384-9 Stationary capacitors used in electronic devices - Part 9: Part specifications: Ceramic dielectric fixed capacitors, class 2

tst EN 60384-20 stationary capacitors used in electronic equipment - Part 20: Part features: Fixed metallized polyphenylene sulfur film dielectric surface mounted capacitors

TS EN 60384-23-1 Stationary capacitors used in electronic devices - Part 23-1: Standard of empty specification: Capacitors in metallic polyethylene naphthalate film dielectric installed on a fixed surface - Ez rating

TS EN 60384-13-1 Stationary capacitors for use in electronic equipment - Part 13-1: Standard of empty specification: Capacitors in fixed polypropylene film dielectric metal foil - E rating

TS EN 60384-14-3 Stationary capacitors used in electronic devices - Part 14-3: Standard of empty specification: Fixed capacitors and connection to mains for electromagnetic interference suppression - Level rating

TS EN 60384-16 Constant capacitors for electronic devices - Part 16: Part features: Constant, metal-coated polypropylene film dielectric direct current capacitors

TS EN 60384-17 Stationary capacitors used in electronic devices - Part 17: Part features: Alternating current (aa) and pulse capacitors with fixed, metal-coated polypropylene film dielectric

TS EN 60384-18-1 Capacitors -Fixed used in electronic devices- Part 18-1: Blank detail properties- Solid (mno <(index) 2>) electrolyte aluminum electrolytic surface mounted capacitors- Rating level ez

TS EN 60384-18-2 Capacitors - Used in electronic equipment -Fixed- Part 18-2: Blank detail specifications- Aluminum electrolytic surface mounted capacitors with non-solid electrolyte

TS EN 60384-19-1 Stationary capacitors for use in electronic equipment section 19-1: Standard of empty detail specification: Fixed metallic polyethylene terephthalate film condensers mounted on a dielectric surface - Ez rating level

TS EN 60384-2-1 Stationary capacitors for electronic devices - Part 2-1: Empty detail characteristics: Constant, metal-coated polyethylene terephthalate film dielectric direct current (da) capacitors - Rating levels e and ez

TS EN 60384-25-1 Stationary capacitors used in electronic equipment - Part 25-1: Blank detail specification standard - Surface mounted fixed aluminum electrolytic capacitors with conductive polymer solid electrolyte - Rating level ez

TS EN 60384-16-1 Stationary capacitors used in electronic devices - Part 16-1: Blank detail specification standard: Capacitors in fixed metallic polypropylene film dielectric - E and ez rating level